Search Documents

By Robert L. Frantz

The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral f Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WW) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental under- standing of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.

Jan 1, 1986

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By J. E. Urosek

In October, 1990, a fire started in a large underground coal mine in Western Pennsylvania. During fire-fighting activities, an explosion occurred and all personnel were evacuated. Safe re-entry into the mine was not possible and the mine was sealed. Recovery efforts began in January, 1991 and continued until March, 1991, when permanent underground seals were installed between the fire area and the mine openings. This paper describes an extensive atmospheric monitoring program conducted by the Mine Safety and Health Administration (MSHA), Pittsburgh Safety and Health Technology Center (PS&HTC) including the analysis of mine fire gases, natural ventilation, fan pressure and air quantity distribution.

Jan 1, 1993

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide's Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? This is one of the most frequently asked questions today. We, in the industry, ask it of each other when we meet; however, the technical answers may vary from "I don't know" to 'quite good" from people within the same company. Management also poses this question because it plays a vital role in our planning for future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, water application, etc. Each has a bearing on the rate of recovery. OPERATIONAL DATA Our method of water distribution is unique in that each dump is drilled to allow physical injection of water into the dump. The in¬jection holes are drilled vertically, on 251 centers, from the surface of the dump. Normally, the holes are drilled 40' deep and cased with 4" PVC perforated pipe.. The pipe is perforated at one-foot intervals with four V diameter holes at 901 spacing on the pipe circumference. We formerly alternated shallow holes (20'-40') with deep holes (80'-l80') in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile, We prefer to have the deep holes end 20'-30' above the original ground level. This generally allows us to penetrate the coarse material at the bottom of the dump. We had to discontinue the deep holes_ in order to cover more dump area in a shorter period of time to meet increased production requirements.

Jan 1, 1972

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990