Search Documents

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By R. E. Pennington

My subject this morning is coal liquefaction technology. Actually, coal liquefaction involves a number of technologies in a very complex system. The first slide shows the major components of such a system with arrows to indicate appropriate flows. The components are the facilities for coal feed preparation and handling; the coal hydrogenation or base liquefaction section; facilities for product separation and recovery, and in addition, facilities for the production of hydrogen from coal-based sources. A very rough break- out of the investments involved in these areas is given at the bottom of the slide. Investment is spread about equally among the three areas of operations Another way of looking at it is that the investments in what might be called support facilities are of the same magnitude as the base investment in the hydrogen facilities. Therefore, it is appropriate in a discussion of coal liquefaction technology to treat it as a system composed of a number of technologies. The next slide lists the various functions in the feed preparation section along with an indication of technology status. Storage, crushing, grinding, drying of coal all have been in commercial practice for a number of years. The slurrying and pumping of coal at least in water slurries, is practiced commercially also. The heating of coal slurries in oil to high temperatures under pressure is not in commercial practice and development and testing is going on by a number of people in this area. Some rather complex phenomena occur when coal oil slurries are heated to high temperatures.

Jan 1, 1975

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

An upgrade to Vale?s existing Clarabelle dual-pinion, semiautogenous (SAG) mill was completed by the power and automation technology company, ABB. The mill is used to reduce the size of the ore at the company?s nickel and copper mines in the Sudbury area. The project was completed on time and on budget with an excellent safety record. Located in Ontario about 400 km (250 miles) north of Toronto, Vale?s Sudbury operations are primarily underground nickel sulfide mines, with integrated mining, milling, smelting and refining operations. One of the characteristics of Clarabelle Mill is to accept nickel-copper ore from various sources and companies and to produce a nickel-copper concentrate and copper concentrate for further processing. The size of the ore is further reduced in SAG mills, rod mills and ball mills, where all milling is done wet.

Mar 1, 2014

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By L. K. Eigenbrod

Throughout the mining industry, pneumoconiosis is one of the most severe occupational health problems being faced. The goal of completely eliminating pneumoconiosis as an occupational health hazard was underscored by the Federal Government with its enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969). Under this law, permissible dust level standards will be placed at 2 mg/m3 in mine atmospheres by December 30, 1972. The mining industry is thus faced with the tremendous technical challenge of achieving this level. Two basic questions can be raised with regard to this legislation. First, does a maximum dust concentration of 2 mg/m3 prevent the occurrence of pneumoconiosis? Secondly, can this dust standard be achieved using presently available methods and equipment? A precise answer to the first question has not yet been developed by the medical profession. Studies are continuing on the origin, prevention, and therapy of pneumoconiosis, and permissible dust levels could become even lower as medical evidence accumulates. The mining industry has addressed itself to the problems of dust con-tro1 for many years as related to personnel health, explosive mixtures, visibility, and machinery damage. Dust control methods being employed involve

Jan 1, 1971

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environ-mental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 1, 1977

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By W. E. Bardelmeier

The high speed conveyor type self unloading bulk carrier concept has been around for about 70 years. Although the design was developed, refined and steadily improved in the Great Lakes, to date limited numbers of such vessels have emerged in the bulk ocean trades, and these have tended to concentrate within specific mineral trades. For example, North American gypsum companies have embraced conveyor self unloaders to the point where such vessels almost exclusively carry the gypsum requirements of this part of the world. One major aluminum company has developed an impressive fleet capability in self unloaders. Application of other ships tends to be fragmented through several mineral trades. A few years ago a new phenomonen began to appear on the Great Lakes. Whereas it had historically been accepted in that region that self unloaders were effective vessels for the minor bulk trades including limestone, coal, salt, gravel and sand; they had seldom been employed heavily in the big volume iron ore trades. Suddenly, however, the new generation of 60,000 ton Lakers which emerged were all designed as high speed self unloaders. The new vessels intended to trade especially in ore, or alternatively especially in coal, have somewhat different internal features, but the important point is that all are self unloaders.

Jan 1, 1979

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By Karin Bäppler

Mechanized tunnelling is undoubtedly one of the most innovative disciplines in the international construction industry. Technological progress in the planning and production of most modern infrastructure is constantly striving for new records on basis of highly specialized solutions and know-how. Humans and technology have accomplished excellent achievements over the past few years in varied, difficult terrain. New length records are being set with the 64 km long Brenner Base Tunnel and the HS2 Railway system currently under construction in Europe. Cities are building ever longer and more demanding sewer tunnels. The paper highlights some of the challenges, trends and innovations of long-distance tunnelling projects.

Dec 1, 2022