Search Documents

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By Kenneth S. Johnson

Oklahoma is the only; state in the nation that is currently producing iodine. The iodine is extracted from iodine-rich natural brines being pumped from deep wells drilled into Pennsylvanian sandstones in the Anadarko basin of northwestern Oklahoma. Woodward Iodine Corp., started in 1977, was the first plant in the United States built for iodine recovery since the 1930s. At present, three companies are operating four iodine-producing facilities in northwestern Oklahoma. The combined production of these facilities, 1,321,000 kg in 1997, is about 26% of the U.S. annual consumption. Iodine is present in concentrations ranging from less than 100 ppm (parts per million) to as much as 1,560 ppm in brines in various Paleozoic strata in the subsurface of northwestern Oklahoma; these concentrations are exceptionally high, and are well above those of any other known brines in the world. Strata with the highest iodine content in the area (Mississippian limestones) have low permeabilities, and thus would yield only small amounts of brine. On the other hand, the lower Morrow sandstones (Lower Pennsylvanian) have a relatively high permeability and are capable of yielding large quantities of brine that average 300-350 ppm iodine. The Morrow brine reservoir was deposited in shallow-water-marine and intertidal-shelf environments and now is buried 6,000-10,000 ft below the land surface. Production is localized to Morrow channel deposits confined to an Early Pennsylvanian paleovalley that is 1-2 mi wide, is about 70 mi long, and is referred to informally as the "Woodward trench." All three companies are producing iodine-rich brines from Morrow sandstones in three different parts of the Woodward paleovalley, and one of the companies also is extracting iodine from oil-field brines coming from several petroleum reservoirs near Dover, about 80 mi east of Woodward. The basic extraction method employed by Woodward Iodine Corp. was used in Louisiana and California operations in the late 1920s. This method is commonly called the air-stripping process. Lower Morrow brine containing dissolved sodium iodide is pumped to the plant through a series of pipelines, where by-product natural gas is separated and processed. The brine is then acidified and subsequently oxidized with chlorine to convert the iodide to iodine. The iodine is air stripped and reabsorbed with sulfur dioxide and water, converting it to hydriodic acid, or process liquor. The process liquor is then processed, using chlorine once again, to crystallize the iodine as a solid. This is then melted and frozen to form a solid product, which is packaged in 110-lb (50-kg) drums and shipped to end users throughout the world.

Jan 1, 1999

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By Yinan Zhang, Y. Luo

Most of the reported coal spontaneous combustion events occur in surface and underground mines where low rank coals (i.e., subbituminous and lower for this particular studies) are extracted indicating their high propensities for spontaneous combustion. Low rank coals have high moisture content (15 to 45%) and are capable of absorbing more moisture in dried condition. However, it is hard to induce the initial stage of self-heating process for the low rank coal using the current laboratory R70 testing method — a method widely used in the coal industry. Like a sponge, dry low rank coals can absorb water vapor in the air while the heat contained in the moist air is transferred to coal and served as the required activation energy to initiate the coal self-heating process. In order to prove this theorem and quantify the effects, the R70 adiabatic oxidation testing method has been improved to introduce a controlled moist flow into the coal reaction vessel. Tests using the new method and its setup on low rank coals showed that the initial self-heating process of coal sample can be greatly accelerated by the added water vapor — impossible with the regular R70 method. Once the self-heating is sustained, the removal of air moisture can further accelerate the process.

Sep 17, 2021

By James R. Walpole

Less than 100 years ago the first major federal regulatory agency, the Interstate Commerce Commission was established (in 1887), and since that time literally hundreds of other federal agencies have been created. The regulations set by these agencies tremendously affect the individual citizens of this country as well as U.S. institutions. A few examples of the myriad agencies established include the Food and Drug Administration. (1907), the Bureau of Mines (1910), the Federal Reserve System (1913), the Federal Trade Commission (1914), the Tennessee Valley Authority (1933), the Securities and Exchange Commission (1934), the National Labor Relations Board (1935), the Small Business Administration (1953), the Federal Maritime Commission (1961), the Equal Employment Opportunity Commission (1965), the Farm Credit Administration (1971), etc., etc. Eight years ago, on December 2, 1970, still another federal agency was established by the reorganization plan of President Nixon -- the Environmental Protection Agency (EPA). The Administrator of EPA was given authority to regulate certain activities affecting the environ-ment, which were formerly within the jurisdiction of the Department of Interior, the Department of Health, Education and Welfare, the Federal Radiation Council, the Atomic Energy Commission, the Department of Agriculture, etc. Within weeks after the formation of this Agency, Congress began to enact legislation which would be administered by EPA. Over the last eight years a considerable number of such laws have been passed, a few of which include: the Clean Air Act (1970), the Noise Control Act (1972), the Federal Water Pollution Control Act (1972), the Marine Protection, Research, and Sanctuaries Act (1972), the Federal Insecticide, Fungicide and Rodenticide Act (1973), the Safe Drinking Water Act (1974), the Toxic Substances Control Act (1976), the Resource Conservation and Recovery Act (1976), the Clean Air Act Amendments of 1977, etc. It may be helpful to review, in a summary fashion, the major provisions in some of these statutes, and accompanying regulations, as they relate to water quality control in the mining industry. The Safe Drinking Water Act and the Federal Water Pollution Control Act contain provisions to be examined, as well as the Resource Conservation and Recovery Act and the Toxic Substances Control Act. One other law, the Surface Mining Control and Reclamation Act (1977), is not administered by EPA although it does contain many provisions related to environmental control, and it will also be dis-cussed because of its importance to the mining community.

Jan 1, 1978

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By H. Jiang, Y. Luo

The study develops an automated, high-efficiency drilling control system to reduce respirable dust and increase energy efficiency in underground coal mines. It uses specific energy to evaluate efficiency and proposes a comprehensive drilling control algorithm based on laboratory tests. The algorithm optimizes drilling parameters to maintain high efficiency, reduce dust generation, and improve safety.

Feb 12, 2022

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand's approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By Yuexin Han, Wenbo Li, Xinran Zhu, Pengchao Li

A multi-stage fluidization magnetization roasting is a promising method to treat limonite ore. The dehydroxylation of limonite ore is a key reaction in the pre-heating stage. In this study, the dehydroxylation mechanism of limonite was studied in a laboratory fluidization roasting reactor. The samples were characterized using in situ X-ray diffraction, Fourier transform infrared spectroscopy, and simultaneous thermogravimetry and differential scanning calorimetry analysis. The phase transformation and kinetics analysis were studied. Results indicated that the dehydroxylation occurred at the temperature of 250–350 °C with the vanish of hydroxyl functional groups (-OH). The dehydroxylation kinetics followed the 2-D diffusion (Jander) reaction model G(α) = [1 − (1 − α)1/2]2, and the calculated activation energy was 113.43 kJ·mol−1. This study is conducive to exploiting limonite ore resources using magnetization roasting technology.

Nov 2, 2023

By Nikhil Dhawan, Sanjay Pindar

The limited lifespan, ever-growing demand, and significant lithium and cobalt content are responsible factors for the immediate recycling of discarded lithium-ion batteries. Discharged batteries were dismantled, segregated, and size reduced to recover cathode and anode material. The active cathode material comprises LiCoO2 (65.8%) and LiMn2O4 (34.2%) and was carbothermal reduced with recovered graphite in a microwave furnace followed by water leaching and magnetic separation. A Box Behnken statistical experimental design is used for process optimization. Both cobalt and manganese report to magnetic fraction, whereas graphite and lithium carbonate report to non-magnetic fraction and solution crystal respectively. The final product comprises of cobalt 73% and manganese of 14% with process yield of 36% and saturation magnetization of 76 emu/g.

May 16, 2020

By D. D. Runnells

In order to establish meaningful remediation goals and monitoring programs in areas disturbed by mining, it is desirable to determine the natural metals concentrations that existed in the area prior to mining. At Iron Mountain, California, several natural sources exist for acid drainage and loading of metals to Slickrock and Boulder Creeks. This paper describes methods to determine the contribution of copper and zinc to groundwater and surface water from those sources, including natural gossan rock outcrops, mineralized bedrock, and colluvial materials. Methods used include evaluation of: 1) historical information, 2) literature values of unmined, mineralized areas, 3) analyses of water from monitoring wells, 4) leaching studies, 5) statistical analysis, 6) isotopic studies, and 7) identification of background by elimination of mining sources. Results from this natural background determination show that Boulder Creek and Slickrock Creek carried elevated concentrations and loads of copper and zinc prior to mining activities. With repeated rinsing of reclaimed and remediated mine materials by rainfall, there will be a diminishing contribution from residual waste rock and tailings at Iron Mountain, and natural background will become an increasingly larger proportion of the total load.

Jan 1, 1999

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990