Search Documents

By G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than four percent P205 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low grade feed In sea water required that the conventioinal Crago Process, comprising direct anionic flotation, deolling, and inverse cationic flotation be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1986

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By Jürgen Kretschmann

Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way or substitutes are pushing the mined products out of the market. An example of the latter is the increasing replacement of coal with natural gas and renewables in power generation in the United States [1]. According to the model of the product lifecycle, the global hard-coal mining industry has reached a stagnation phase [2]. The trend is obvious. Coal use peaked in 2013 [3], and the coal demand of China has been slowly decreasing since then [4]. Coal consumption in the United States saw a 16 percent decline from 726 Mt (800 million st) to 608 Mt (670 million st) between 2015 and 2019. In addition, according to the U.S. Energy Information Administration, it will not rise again [5]. The decline is attributed to complex market dynamics, from low gas prices because of the “shale gas revolution” [6] to federal environmental regulations like the Clean Power Plan. Moreover, important players like the United Nations and the European Union have already begun to describe pathways toward decarbonization. Increasing competition between coal-mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries, like France, Spain or Germany, are only forerunners of this development — their centuries of coal production have passed. The concept of sustainable development (SD) is fundamentally based on a model of progress in which ecological, economic and social dimensions should be developed equally and positively. Questions arise, such as: How can SD be a corporate goal in a phase of decline? How can former mining regions sustainably progress to a better future? The steps Germany has taken to handle the coal decline in a sustainable way and the lessons learned from this process are described in this paper. 

By Steven W. Hunt, Glen R. Frank

Assessment of abrasivity and cutter life are necessary to properly manage risks when tunneling in mixed face ground which includes ground with cobbles and boulders. Maximizing cutter life requires: (1) abrasivity and strength parameters for soil matrix and rock clasts, (2) methods of combining both, (3) proper selection of cutters and (4) modified TBM operation including use of boulder detection methods from the TBM to help make operation decisions. This paper presents approaches for addressing these factors sufficiently to improve tunneling success in mixed-face and cobbly-bouldery ground. Current laboratory abrasivity testing will be assessed along with equivalent quartz content correlations to soil matrix and rock clast abrasivity. New approaches to combining abrasivity testing of both the soil matrix and rock clasts for various cobble and boulder volume ratios will be suggested to estimate cutter life and intervention intervals. Methods for detecting boulders and using detection data to modify TBM operations to minimize boulder impacts are provided.

Jun 13, 2021

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By Robert W. Holliday

Natural resources are the reservoir from which society draws its material sustenance. Although there is a growing awareness of the need for aesthetic resources such as space for recreation and natural beauty, the basic resources are soil, air, water, and minerals including fuel. Minera's and all sources of energy gain in relative importance with advancing technology and expanding industrilization. In the highly industrialized economy of the United States, almost every aspect of man's life is touched in some way by a product of, the mineral; industries. Agriculture owes much of its productivity to mineral-based fertilizers, insecticides, and mechanical equipment. Modern construction, manufacturing, communications, and transportation are all dependent on nonmetallic minerals, metals, and fuels. Throughout history, those nations with access to minerals, and the technology for using them, have gained ascendency. Before World War II the leading powers also were, leading coal producers. In order of declining rank the five leading' coal producers were the United States, the United Kingdom, Germany, the USSR, and Japan. That the military victory went to the side with the greater' capacity to convert iron and coal into tools of industry, and weapons, is' more than coincidence. It is a fundamental' fact of existence. It is axiomatic that the United States must have a continually increasing supply of minerals if we are to meet the needs of our burgeoning population for a comfortable standard of living and for national security.

Jan 1, 1968

By P. Soros

Rich iron ore deposits were discovered during the 1960's in the mountain range of Serra dos Carajas, State of Para, Brazil, near the headwaters of the Tocantins River some 400 miles southwest from the state capital of Belem. (See Fig. 1 and 2). The key to the successful exploitation of this deposit was the development of an efficient an economical transportation system. The rugged terrain, and the dense tropical vegetation of the Amazonian jungle and the irregular coastline with its high tidal range presented severe obstacles to the planning and building of such system. Starting in 1972 extensive surveys and studies were carried out by Soros Associates on behalf of CVRD to determine the optimum way of transporting the ore from the mine site to the markets, most of which are located overseas. Overland transportation to the coast, loading into seagoing vessels and the ocean voyage to the ports of destination was treated as an integrated system in these studies.

Jan 1, 1986

This review provides a new and comprehensive summary on studying colloidal interactions encountered in mineral processing with representative examples for critical information, which are of great scientific and practical importance. Colloidal interactions play a vital role in mineral processing, including grinding, physical separation (particularly flotation), dewatering and tailings management (Fig. 1). Despite great energy input in comminution to liberate valuables from gangues, hetero-coagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. The importance of colloidal interactions is becoming increasingly significant as we process ever more finely disseminated low-grade ores as a result of inevitable depletion of high-grade ore deposits. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. 

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By Junnan Chen, Hongwei Zhang, Wei Wang, Feng Xie

Thiosulfate is a green gold leaching agent that shows great potential to replace the highly toxic cyanide. Ammonia is traditionally used as the copper ligand in thiosulfate solutions to reduce the reactivity of copper ions towards thiosulfate, but it is a toxic reagent. As a result, efforts to replace ammonia with another complexing agent have received increasing attention. In this study, a novel alternative to ammonia is proposed to explore the potential use of the copper-malic acid-thiosulfate system. Experimental parameters include temperature, initial pH, copper, malic acid, and thiosulfate concentration. The feasibility of the copper-malic acid-thiosulfate system was discussed using Eh–pH and species distribution diagrams. Themodynamics analysis indicates that the mechanism of gold leaching in copper-malic acid-thiosulfate solution is mainly catalyzed by the Cu2( Mal)2H-2 2−/Cu(S2O3)3 5− redox couple. The capability of gold leaching in this system for processing the refractory gold concentrate is comparable to that of cyanidation and the traditional copper-ammonia-thiosulfate leaching processes. Thiosulfate consumption is greatly reduced in the presence of malate due to its strong chelating effect on the copper ions. Moreover, the copper-malic acid-thiosulfate system demonstrates a significant enhancement in leaching kinetics, making it a viable option for processing refractory gold concentrates.

Aug 1, 2023

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By T. Umadevi, A. Pratap Singh, R. Sah, K. Abhishek

"It was possible to beneficiate a low-grade iron ore fines sample from Bellary-Hospet, Karnataka, India assaying 56% Fe, 9.1% SiO2 and 5.2% Al2O3 and produce two concentrates, namely, a sinter-grade fines concentrate (43.7% by weight), assaying 63.6% Fe, 2.6% SiO2 and 1.7% Al2O3, and a pellet-grade concentrate (30.7% by weight) assaying 64.7% Fe, 2.9% SiO2 and 1.7%Al2O3. Rejects (25.6% by weight) assayed 32.5% Fe, 27.9% SiO2 and 15.4% Al2O3. The mineralogical characterization indicated that the sample consisted of 69.5% ironbearing minerals (56% hematite, 7.5% martite and 6% goethite-limonite), 12.5% quartz and 15.2% clay, and the rest were minor minerals. Liberation size was found to be in the size range of 25 to 100 µm. The process flow sheet consists of jigs, spirals, grinding and low- and high-intensity magnetic separation of the deslimed feed. IntroductionJSW Steel Ltd is a 10-Mt/a integrated steel plant. To produce 10 Mt/a hot metal requires nearly 16 to 20 Mt/a iron ore fines. The fast depletion of highgrade iron ore fines, increased industrial demand and an increase in iron ore prices have necessitated the exploitation and use of low-grade iron ore fines in the steel-making process after beneficiation. Thus, the beneficiation of low-grade iron ores by removing the associated gangue minerals and enhancing their grade is essential. The use of these iron ore fines in sinter and pellet making has prompted the undertaking of systematic studies on low-grade iron ores.Finely disseminated low-grade iron ores with siliceous impurities have been upgraded by gravity, magnetic and flotation-based processes (Burt, 1994; Svoboda, 1987; Houot, 1983). The processing of low-grade Indian hematite ore containing high levels of alumina-bearing minerals as impurities present separation challenges and pose special problems in martite and magnetite, in association with quartz and clay as the gangue-forming minerals. Alumina is mainly contributed by clay (kaolinite, montmorillonite, illite, alunite), lateritic material and gibbsite; some alumina occurs as solids in iron oxide minerals, namely, goethite and limonite. Silica is mainly contributed by quartz and the associated clay. achieving a high-grade concentrate (Pradip, 1994; Singh and Mehrotra, 2007). Hematite ore basically consists of varying amounts of hematite, goethite,"

Jan 1, 2015

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020