Search Documents

By Ken Deter

I have some general comments on optimizing profitability based on working in heap leach operations in tropical environments. Many of my planned comments this morning have been stated earlier in the Conference. I get the opportunity to say only a few words, and follow up on some specific comments and concerns. In normal operations, stack the ore higher, where possible. The surface area of the stacked ore controls the total solution volume that can be sprayed on the pad at a specific time period. With higher lifts, solution will contact more ore particles as it percolate through the lift, and therefore the solution grade flowing through the base will be increased, whether it is freshly stacked or almost completely leached ore. This also allows more tonnage to be stacked per lift on the pad, decreasing conveyor movement and downtime. Increasing from 6 to 8 meter (20 to 26 feet) lifts have worked successfully, and some mines are using 10 meter (33 feet) lifts in 10,000-15,000 dmtpd plants. The same concept will work with smaller plants, but initial 6 meter lifts should be used until the start-up period has shown the leaching is working as planned. As the stacked ore lifts get higher, the solution flowing through the highest lift is diluted by solution retained in the lower ones. Eventually no real increase is noted from putting fresh ore in service, and gold production rate suffers. To address the dilution problem, an HDPE liner should be installed between each 2 to 4 lifts, depending on each site specific lift height, recovery, % slump in the lift, recovery rates, and grade treated, among others. The surface of the previous lift should be leveled and sloped to control the effluent draining from the planned lift, then the liner is placed, including berms and discharge pipes. The intermediate HDPE liner does not need to be completely sealed as would be the case with the base liner, and can accept some solution penetrating into the lower lifts. A one-mm (40-mil) thickness liner can be used. This intermediate liner allows the upper lift(s) higher-grade effluent to report to the pad discharge point. This will maintain higher gold solution grades going to the ponds. The slopes of the previous lifts should not be covered with HDPE in this concept, and precipitation falling on the lower lift slopes and benches can be directed to barren or surge ponds.

Jan 1, 1999

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By Paul C. Miclea

In case of a major fire in a tunnel between stations or ventilation shafts, if the buoyancy effect of the hot gasses is stronger than the airflow induced by the fans, the risk of backlayering could restrict the safe evacuation of people. Obstructions in the tunnel and alternate airflow paths can further reduce the air velocities past the fire. Currently there are two computer programs available to address the issue of underground fires: o "Subway Environment Simulation" (SES), Version 3.0, developed by Associated Engineers, a Joint Venture of Parsons Brinckerhoff Quade & Douglas, Inc., De Leuw Cather & Co., and Kaiser Engineers, Inc. for the U.S. Department of Transportation o "MFIRE", Version 1.26, developed at Michigan Technological University for the U.S. Department of the Interior, Bureau of Mines. As implied by its name, the SES program was developed specifically for the analysis of subway ventilation systems. It can be used to analyze the heat released into, and removed from, a subway or vehicular tunnel and to determine the effect of ventilation elements on airflows throughout the network of stations or other merging tunnels. It has a special feature allowing the user to predict the effects of a fire at any location within the subway system. Version 3.0 of the SES program is designed to be used with a "critical velocity" calculation in order to determine whether or not tunnel airflows can be controlled during a train fire emergency. The original version of the program was written in FORTRAN for mainframe computers, such as the IBM 4381. Recently ICF Kaiser Engineers has compiled a version of the SES program for PC use. The MFIRE program simulates the interdependence between a mine ventilation system, with its pertinent fans and structures, and changes in ambient conditions or a source of heat, such as a fire. It also accounts for natural ventilation. The program is written in FORTRAN 77 and compiled for 8086/8088 based microprocessors, allowing it to be run on an IBM PC or compatible computer with a 2.0 or a later version of DOS, 256K random access memory (RAM), and a text editor. This paper reports the comparative results of an application of both programs for the same network in a recent study.

Jan 1, 1991

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

In 2011, the value of mineral production increased in the United States for the second consecutive year (Table 1). Production increased modestly for most mineral commodities mined in the United States, and price increases, especially for precious metals, resulted in increases in the value of production. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates. U.S. apparent mineral consumption (industrial) of 11 mineral commodities decreased substantially from 2005 to 2010 (aluminum, cadmium, cement, copper, iron, lead, salt, soda ash, steel, tin and zinc). Data for 2011 were not calculated, but the data show a sustained decrease (especially for the metals) preceding the recession through 2010, so consumption seems to be behaving differently than production and GDP. After continued decline following the 2008?2009 recession, the construction industry began to show signs of improvement during 2011, with increased production and consumption of cement, construction sand and gravel, and gypsum ? mineral commodities that are used almost exclusively in construction. Crushed stone production, however, continued to decline.

Jan 1, 2012

By Miles L. Silberman

Three major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first, most likely, resulted from sub- duction of a Pacific plate (Farallon plate) beneath the North American plate, resulting in eruption of andesitic rocks in the northern Great Basin between 42 and 43 m.y. ago. Between 34 and 17 m.y. ago, igneous activity migrated to the southwest, largely as eruption of volumincus rhyolite-quartz latite ash-flow sheets, ending about 17 a.y. ago with the onset of crustal extension and north-south-trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin; is mostly basaltic or bimodal basalt-rhyolite. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between about 22 to 6 m.y. ago in the western Great Basin along the northwest-trending Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks, but the largest production has come from mines associated with andesitic rocks of the third (western Great Basin) suite. The oldest (34 to 42 m.y.) andesitic rocks (first suite) of the northern Great Basin have produced some large deposits; slightly younger silicic rocks of this suite are mostly barren. Many small ore deposits are associated with the 17- to 8-m.y.-old basalts (second suite) of northern Nevada.

Jan 1, 1976

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Richard F. Hammen

Mineral extraction from sulfide ore deposits usually leads to the combined action of oxygen and water on the newly exposed ore. The result is acid mine drainage, a low pH solution of various metal sulfate salts and sulfuric acid. Paradoxically, the valuable metals dissolved in acid mine water are a liability because they are too toxic for discharge but too dilute to recover economically. The expense of compliance with water quality release standards has reduced the profitability of many mining operations. Solid phase extraction (SPE) columns have been developed to extract metals from acid mine water. These columns are designed to remove the toxic elements from water and recover the metals as purified fractions. This article describes the results of a Phase 1 bench-scale project to test the performance of the SPE columns. The tests were conducted with water collected from the abandoned Berkeley Pit copper mine in Butte, MT.

Jan 1, 1993

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By Muhammad Azeem Raza, Muhammad Zaka Emad, Muhammad Usman Tahir, Saqib Ahmad Saki, Muhammad Usman Khan

Shotcrete is a key initial rock support component used in underground mining and civil projects. The strength of shotcrete plays a vital role in providing and deciding the support adequacy. The strength of shotcrete is evaluated by its uniaxial compressive strength (UCS) test that is usually conducted on extracted core samples. Shotcrete cores are commonly extracted from the test panels along the direction of its application; thus, its strength perpendicular to the direction of application is often neglected. The true bearing strength of shotcrete is thereby ignored despite the fact that higher stresses act normal to the direction of its application. Although the anisotropic behavior of shotcrete is well reported, no study has reported extensive testing of this scale and nature. This study reports extensive testing of shotcrete cores extracted from tunnels of a mega hydroelectric project in Pakistan. The study reports 7- and 28-days strength tests of shotcrete cores. The research also investigates the anisotropic behavior of steel fiber reinforced shotcrete and suggests that shotcrete exhibits higher strength perpendicular to the direction of its application.

Dec 26, 2022

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

The National Mining Hall of Fame and Museum in Leadville, CO seized the opportunity to show off during its 10th anniversary induction banquet on Sept. 6. "We wanted to make people more aware of the mining hall of fame and museum," said Carl Miller, its executive director. The annual event honors inductees into the Mining Hall of Fame. This year, the inductees included Paul Wheeler Allen, Joseph Rosenblatt, Arthur Fay Taggart, Joseph Toy, Joseph Wharton and John Benjamin Zadra (ME, August, pp. 60-63). Allen, of Pasadena, CA and Rosenblatt, of Salt Lake City, are both living. Only Allen was able to attend. This year's induction banquet was the first held in Leadville, North America's highest incorporated city, at 3,094 m (10,152 ft) above sea level. The banquet gave attendees an opportunity to see the museum in its century-old 6,500-m2 (70,000-sq ft) Victorian schoolhouse. Many of the 350 guests came in 1890s dress to the black-tie affair. The evening included a cocktail reception and an open house along with a catered, prime rib dinner. During the open house, attendees had the opportunity to tour the museum's 12 rooms of exhibits and displays. Among items of interest, it was noted that a framed directory of inductees now enhances the entrance to the hall of fame. The directory is organized by the inductees' names and the location of their plaques, allowing visitors to quickly find hall of fame members. Noted mining historian and author Duane Smith delivered the keynote address at the banquet. After the induction of the six honorees, attendees danced to the big-band era music of the Leadville 17-piece band BandAge. Karl Elers was the master ceremonies for the evening's program. He is a member of the hall of fame's board of directors and is chairman of Battle Mountain Gold Co. Allen was honored by the presence of 26 former colleagues and associates. He told the audience that he originally thought the museum should have been located in Denver. "But I have been proven wrong," he said. For many years, Allen was the operational executive of Cyprus Mines Corp. and a key participant in the company's growth. Allen received a replica of his mining hall of fame plaque from Thomas Falkie, chairman of the hall of fame's board of governors and president of Berwind Natural Resources Co.

Jan 1, 1997

Samples collected during the exploration phase of mining represent baseline conditions at the site. As such, they can be very important in forecasting potential environmental impacts should mining proceed, and can become measurements against which future changes are compared. Constituents in stream water draining mined and mineralized areas tend to be geochemically, spatially, and temporally variable, which presents challenges in collecting both exploration and baseline water-quality samples. Because short-term (daily) variations can complicate long-term trends, it is important to consider recent findings concerning geochemical variability of stream-water constituents at short-term timescales in designing sampling plans. Also, adequate water-quality information is key to forecasting potential ecological impacts from mining. Therefore, it is useful to collect baseline water samples adequate for geochemical and toxicological modeling. This requires complete chemical analyses of dissolved constituents that include major and minor chemical elements as well as physicochemical properties (including pH, specific conductance, dissolved oxygen) and dissolved organic carbon. Applying chemical-equilibrium and appropriate toxicological models to water-quality information leads to an understanding of the speciation, transport, sequestration, bioavailability, and aquatic toxicity of potential contaminants. Insights gained from geochemical and toxicological modeling of water-quality data can be used to design appropriate mitigation and for economic planning for future mining activities.

Jan 1, 2011