Search Documents

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

Asgco’s design of the Arrowhead Ceramic Lagging provides solutions to problems experienced with conveyor belt slippage around the drive pulley and severe wear problems on snub and bend pulleys. Asgco has developed a range of pulley lagging from ceramic, drive rubber and non-drive rubber lagging that is available in abrasion-resistant SBR and MSHA grade rubber for conveyor pulleys from slow belts all the way through to high-speed, high load belts. There is a growing need for a maintenance-free and reliable pulley lagging to ensure conveyor belts run to their highest efficiency.

Jan 1, 2006

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By R. Rodgers

The Pinto Valley concentrator of BHP Copper Inc. restarted its sulfide mining operations in September 2007 to produce copper and molybdenum concentrates. During the plant production ramp up, the copper/molybdenum circuit quickly reached the copper grade and recovery targets, but the production and quality of the molybdenum concentrate continued to be a challenge. Even though several improvements in the molybdenum circuit were completed, the final molybdenum concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns were chosen. The column design and construction were done using in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing molybdenum concentrate to the required specifications, that is, high molybdenum tenors and low copper and iron content. The Pinto Valley operations, are comprised of the Pinto Valley concentrator, the Pinto Valley dump leaching and a solvent extraction/electrowinning (SX/EW) plant. The concentrator operated from 1972 to 1998 when mining and milling operations were curtailed for economic reasons. The SX/EW plant continued operations for copper cathode production. After a cessation of mining operations of almost 10 years, Pinto Valley operations began a restart project in January 2007, to bring the mine and the concentrator back into production. Copper concentrate production started in October 2007 after refurbishing and upgrading the facilities with a new DCS system and filter plant. The daily targets of the concentrator were to treat 56.7 kt (62,500 st) of ore, produce 762 t (840 st) of copper concentrate containing 27.5 percent copper at recoveries of 86 percent and produce 2.2 t (2.5 st) of molybdenum concentrate containing more than 80 percent MoS2.

Jan 1, 2010

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By U. B. Kodukula

The iron ore beneficiation plant at Serra-Azul Mines of ArcelorMittal, Brazil operates at a rated capacity of 3.2 million tons per year. The ore is concentrated using magnetic separation, jigging, hydrocyclones and spiral concentrators. The tailings from the process plant are generated from classifier overflow of 135 tons per hour dry solids and thickener underflow of 48 tons per hour dry solids. A systematic experimental program was carried out using Multi-gravity separator (MGS), and wet high-intensity magnetic separator (WHIMS) for recovering the iron values from both of the tailing streams while minimizing the total quantity of tailings to be discarded. The classifier overflow contained 32.3 percent iron, 49.9 percent silica and 2.18 percent alumina and was 45 percent finer than 45 microns in size. The thickener underflow sample contained 47.3 percent iron, 27.6 percent silica and 2.49 percent alumina and was 16 percent finer than 45 microns in size. Separation results on the classifier overflow sample with the MGS indicated that a concentrate containing 62.1 percent of iron, 10.8 percent silica and 0.36 percent alumina can be achieved with a weight recovery of 24.5 percent. The results with WHIMS at 6500 Gauss indicated that concentrate containing 62.6 percent iron, 8.3 percent silica, and 0.65 percent alumina can be achieved at a weight recovery of 34.7 percent. 4.7 percent. WHIMS studies at 6500 Gauss on thickener underflow sample indicated that a concentrate containing 61.4 percent iron, 8.8 percent silica, and 1.74 percent alumina can be achieved at a weight recovery of 57.2 percent. Based on these results, and further in-house test works, a WHIMS installation was adopted for the recovery of iron values from the tailings in the operating plant at ArcelorMittal Serra Azul Mines, Brazil.

Feb 23, 2014

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By L. F. Ruppert, R. C. Milici

Coalbed methane (CBM) is currently being produced from a relatively small area in the Dunkard and Pocahontas basins, in the northern and central parts of the Appalachian Basin, respectively. In general, much of the production occurs where the coal beds are beneath 500 feet or more of overburden, where the rank of the coal is high-volatile B or greater (%Ro >0.8), and where the natural fracture system is enhanced by structural deformation. It is anticipated that near-term CBM development will continue within these areas and will expand in the Appalachian basin as technology improves and as the price of gas rises.

Jan 1, 2003

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352&apos;C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Sean Cassady, Jason Liu, Sanja Zlatanic, Taehyun Moon, Chris Devery

"For the Hollywood International Airport Runway Expansion Project at Fort Lauderdale, Florida, the structural fire durability analysis was completed for a series of tunnels formed by roadway and railroad cells located under the runway structure. A systematic design approach was developed to mitigate structural damage during a fire event and arrive at a practical method to structural fire engineering that is compliant to NFPA 502. To ensure the NFPA 502 requirements are satisfied, the performance based approach was implemented and the engineering analyses were performed for the adopted design fire event. The analyses considered the facility’s unique features including its fire safety systems to determine applicable design fire curves for structural durability analyses. The paper also outlines the process of defining the project specific fire curves for a specific design fire scenario and summarizes the results of heat transfer and structural fire durability analyses. This approach was aimed to assist the owner and Authority Having Jurisdiction to achieve practical decisions to the tunnel facility fireproofing.INTRODUCTIONFort Lauderdale–Hollywood International Airport (FLL) in Broward County, Florida is a major hub facility serving more than 23 million passengers annually. As part of the Airport Expansion Program, the South Runway (9R-27L) Expansion project aimed to meet ever increasing service demands via an increase to runway lengths. This necessitated the placement of one of the reconstructed runways on bridge structures over the existing U.S. Route 1 (US 1), a major north–south U.S. Highway that serves the East Coast of the United States, and the Florida East Coast (FEC) Railway, thus effectively creating multiple tunnel cells beneath the subject runway. For this project, HNTB suggested a tunnel fire damage mitigation system that would protect the runway major structural elements from the design fire event that may happen within the tunnel cells. This paper addresses the issues related to the fire event originating within the tunnel encompassing the US1 highway only, and deals with requirements of NFPA 502 [5] exclusively. Therefore, while approaching the structural fire protection issues for the specific tunnel cells beneath the runway structure, the requirements of the American National Standard NFPA 502 (Standard for Road Tunnels, Bridges, and Other Limited Access Highways, 2008 edition) were followed. Per this standard, regardless of tunnel length, all primary structural concrete and steel elements shall be protected in order to:"

Jan 1, 2016

By G. M. Wilemon

The U.S. Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93 pct sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC. A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1990

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971