Search Documents

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By K. Heatwole, D. Shier, A. Davis, J. Kidder, S. Sunkavalli

"Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios, including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation.IntroductionAcid rock drainage (ARD) is a notable environmental concern in areas where rock or other material with acid generation potential is disturbed. ARD is defined as drainage that occurs as a result of sulfide oxidation in rock exposed to air and water. ARD is characterized by low pH, elevated metals concentration (especially aluminum, iron and manganese), sulfate and high total dissolved solids. The low-pH water that results from acid generation is capable of solubilizing heavy metals contained within the rock. The principal sulfide mineral in mine wastes is pyrite (FeS2). Pyrite oxidation is complex and can involve chemical and biological reactions. Oxidation of pyrite by atmospheric oxygen produces one mole of Fe2+, two moles of SO4 2- and two moles of H+ for every mole of pyrite oxidized, as described by Eq. (1)."

Jan 1, 2015

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By Gordon C. ‘Bud’ Presley

The pumice and pumicite review arrived too late for the June issue. Estimated domestic production of pumice and pumicite in 1992 was up compared with 1991, according to US Bureau of Mines statistics. The Bureau estimate of domestic production of 400 kt (440,000 st) for 1991 turned out to be 401 kt (442,000 st) of actual production, the lowest since 1989. In 1992, the estimated the value of pumice and pumicite sold or used in the United States was $11.6 million, up only $200,000 from the 1991 value. There was an increase in the mine, or mill, average price from the five-year low of $11.44/t ($10.37/st) in 1986 to $26.42/t ($23.96/st) in 1992. Estimated tonnage produced in 1992 was 439 kt (484,000 st). Apparent domestic consumption was 642 kt (707,000 st), up 135 kt (149,000 st) from 1991. Imports for consumption were estimated to be 215 kt (237,000 st) last year. Domestic production supplied 68% of the demand in 1992, with net imports supplying the remaining 32%. This compares with domestic production sup¬plying 53% and net imports supplying 47% of the apparent consumption in 1988. Exports were about 900 t/a (1000 stpy) for the period 1984 to 1988. In 1989, exports rose sevenfold to 7 kt (7700 st) and to 20 kt (22,000 st) in 1990. The Bureau of Mines reported that the amount of pumice and pumicite exported in 1992 was 12 kt (13,200 st). It is assumed that these exports were from the Pacific Coast because imports, mainly from Greece, continued to be a market factor on the East Coast and the Gulf Coast States in the United States.

Jan 1, 1993

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By L. A. Panek

A new pillar strength formula is presented, incorporating a function P of size and shape, which takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive-strength test results as function of P clearly reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1994

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By TUIJA MONONEN, LUDGER BENIGHAUS, CHRISTINA BENIGHAUS, Virginia del Rio, SARI KAUPPI, JUHA M. KOTILAINEN, JAVIER GÓMEZ, JARI LYYTIMÄKI

The understanding of public debates over mineral exploration and mining largely originates from exceptional situations such as mining accidents of conflicts. Less is known about how mining is portrayed and understood under more conventional settings. What storylines dominate the local day-to-day public debate? This article presents results from a comparative case study focusing on newspaper coverage of mineral exploration and mining in three European countries representing different geological and socio-economic contexts. Newspaper articles from the Geyer-Erzgebirge region in Germany, the Andalusia region in Spain, and Northern Finland are studied. The sample looks into the period between September 2018 and February 2020 and shows that regional newspapers report about mining issues relatively intensively even in the absence of major accidents or other media events causing peaks of attention. The tone of the articles is generally neutral to positive towards mining activities, reflecting the specific local settings, historical experiences, and future expectations. Despite the different contexts of the three countries, there were considerable similarities to the topics highlighted, including common themes of mining revival, mining events and social interaction, history of mining, and damages related to mining. Past, present, and future employment opportunities related directly or indirectly to the mining sector are key storylines. Another recurrent underlying theme is the need to balance environment and safety risks and socio-economic prosperity, typically covered through ordinary disputes among the mining sector, public authorities, regional non-governmental organizations, and local initiatives.

Jul 6, 2021

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By R. B. Tippin

Great Salt Lake Minerals & Chemicals Corporation (GSL), a subsidiary of Gulf Resources & Chemical Corporation, is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, Utah. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The GSL Sulfate of Potash Complex The GSL potash complex (depicted in Figure I) is divided into a solar evaporation pond system and the process plants. The solar,evaporation system consists of a 17,000-acre (68.8 Km2) ponding operation where the various salts deposit during the summer evaporation season, and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit con¬taining primarily kainite (KCl-MgSO4.3H20), schoenite (K2SO4?MgSO4^ 6H2O), and halite (NaCI), with some carnallite (KCl.MgCl2.6H20) and epsomite (MgSO4.7H20). Other minor minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During, a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content

Jan 1, 1977

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991