Search Documents

By k. Osei-Boakye

This paper presents the calibration of a real-time aerosol monitor, the TSI DustTrak?, to the NIOSH 5040 method being used by the Mine Safety and Health Administration (MSHA) for compliance enforcement evaluation. The standard NIOSH 5040 instrument for compliance evaluation of diesel particulate matter (DPM) has an inherent time lag of up to two weeks for laboratory processing of sample results. Therefore, providing the underground mines with a means of quantifying DPM conditions in real-time, will enable them to efficiently and effectively manage DPM levels to ensure compliance with the regulated limit.

Jan 1, 2009

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By R. Adsero

The analysis of equipment trends in AUSIMM?s Revision of Monograph 19; Australasian Mining and Metallurgy Operating Practices (AMMOP) in the paper by Dight et al (in press) raised some interesting and in parts disturbing trends in the Open Cut Mining Industry. According to the US Bureau of Labour Statistics the US mining and petroleum industries? productivity is down by 12% since 2004 while the Australian Bureau of Statistics shows the productivity of the Australian mining industry is down by 34% since 2001. In terms of open cut equipment median output for draglines is down by 15% since 2003; electric rope shovels are down by 41% since 2003; hydraulic excavators are down by 39% since 2008; front end loaders are down by 39% since 2007 and trucks are down by 41% since 2006. Clearly the boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top 10% by annual output per unit of input) has declined but not by as much as the median (eg. shovels down by 8%, excavators down by 19% and FEL?s down by 5%). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one will be crucial to reversing the decline in open cut equipment performance.

Feb 27, 2013

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By W. J. Nokleberg, B. A. Bouley, T. K. Bundtzen

Central Alaska contains a wide variety of pre-, syn-, and post -accretionary mineral deposits that are related to the growth and evolution of the north-west North American continental margin. Withinpre-accretionary terranes, the Devonian-Carboniferous, carbonate platform-hosted MVT zinc-lead deposits of the Kandik and Reef Ridge districts in central Alaska, and the Devonian-Mississippian volcanogenic massive sulfide (VMS) polymetallic deposits of the Bonnifield, and Delta mineral belts of eastern Interior Alaska have received the most exploration interest to date. Syn-accretionary rift related, mafic and ultramafic sill swarms and zoned plutons of the Kluane-Nikolai igneous belt are currently being explored for Ni-Cu-Co-PGE deposits. Syn-accretionary granitoid complexes in the PurcellMountains, Illinois Creek, and Sitylemenkat areas have been explored for uranium-REE-gold, and tin-silver mineralization respectivelyPost-accretionary granitoid intrusions and associated volcanic fields that range in age from mid-Cretaceous to early Tertiary contain significant gold-silver-polymetallic resources in the East Central Alaska, Hogatza, and Kuskokwim Mineral belts. Collectively the three main post-accretionary plutonic/volcanic belts of central Alaska are part of the Tintina Gold Province, where exploration since 1990has identified about 848 tonnes gold.

Jan 1, 2000

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By R. J. Kline

Most accidents are the result of risk taking. They can happen anywhere. Our coal industry categorizes accidents by type, occupation, commodity, age, every way you can imagine. We now know, how many were injured and when, for all the different types of accidents. We have ask ourselves many times, why are we having accidents, how can we stop the accidents and fatals in our industry? Present numbers and projections do not show that this will happen. Serious accidents can result in fatalities. Fatal accident can be prevented, and the coal industry can achieve zero fatalities. How soon this happens, depends on a great number of factors. I will discuss accidents and reasons for us having accidents in an attempt to get to the root causes. The historical perspective will be touched on, and the risk and analysis of accidents will be probed.

Jan 1, 2000

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007