Search Documents

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By J. E. Urosek

Decisions made during a response to a mine fire or an explosion greatly affect the final outcome. The safety of miners should be the primary concern with accounting for all of the miners the first issue for resolution. If miners have not safely evacuated from the mine, the last known location of the miners at the time of the event and anticipated travel routes are primary exploration areas. After the mine is evacuated, there are many very important decisions that must be made quickly and often under great stress. It is critical that the mine operator establish an orderly method to direct the mine emergency response. Designation of a Command Center, staffed with personnel charged with developing plans, is a common method of establishing control. Scheduling of key mine managers will be critical, since decisions must be made 24 hours a day and people working for extended periods with little or no sleep do not always make clear or cognizant decisions. Internal communications, passing information on to subsequent shifts, and external communications with families and media must be accurate and timely. Assembling resources for responding to the mine emergency is critical for an effective response, and pre-planning can pave the way to a successful recovery. Sampling mine gasses and accurately determining the composition of gas mixtures is a common tool used to develop response plans in all fires and explosions. It is essential that preparations for emergency situations are made well in advance of a disaster. Effective communications are essential for mine management to successfully respond to a mine emergency. This paper discusses some considerations which need to be addressed in directing a response to a mine fire or explosion.

Jan 1, 2009

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency has been widely used by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which follows. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided. The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies. OUTLINE Introduction and Background Part 1. Determining the Bond Efficiency of a Grinding Circuit Method Demonstration/Example Calculations Bond Work Index Testing Equipment and Procedures Accuracy of Comparative Circuit WI Efficiency Determinations (under development) List of Symbols Part 2. Data Base of Bond Grinding Circuit Efficiencies (under development) References Annexes: A1. The Bond Crushing WI Test Equipment and Procedure for Bond Efficiency Determinations (Revised March 26, 2015) B1. The Bond Rod Mill WI Test Equipment and Procedure (Revised March 26, 2015) C1. The Bond Ball Mill WI Test Equipment and Procedure (Revised March 26, 2015) Introduction and Background Please see the references and slide presentation “Bond Efficiency SLC (rev3)-print.pdf.” This efficiency determination applies to most brittle materials in their naturally occurring (un-scalped) size distributions being treated in size reduction circuits down to a product sizing of approximately eighty percent passing 70 µm (see below). Unusually shaped materials (e.g. mica) should be regarded with caution. Part 1. Determining the Bond Efficiency of a Grinding Circuit Method In the plant: • Define the circuit for which the WI efficiency is to be determined • Procure samples of the circuit feed and product • Obtain the power draw of the size reduction equipment at the drive pinion(s) • Obtain the circuit throughput rate (dry tonnage) In the laboratory:"

Jan 1, 2016

By Derek J. Penrice

The Caltrain Downtown Extension (DTX) project will extend commuter and future statewide high-speed rail service into the Transbay Transit Center, which will be located in the business district in downtown San Francisco. The DTX project includes 1.5 miles of underground construction, comprising complex sections of mined and cut-and-cover tunnel. As part of the DTX preliminary engineering process, development of appropriate contracting practices, including contract packaging, procurement methods and contract terms for the underground construction, has been initiated. This paper provides a summary of the evaluations undertaken, preliminary conclusions reached, and proposed next steps to promote industry interest and maximize bid competition.

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today's economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By J. E. Bernick, J. Davies

This paper describes the design and construction of a 22.86 m (75 ft) long jacked tunnel, which was successfully installed, despite difficult mixed face conditions at Metro-North’s Westport Station, in Connecticut in the fall of 2003. The tunnel utilized what is believed to be, the first application of a steel grillage system within the United States. This grillage was installed before the jacking started and allowed the tunnel to be jacked under four live railway tracks, which included the Acela high speed line, without affecting train operations. The clearance between the top of the tunnel and the rails was only 0.9 m (3 ft).

Jan 1, 2005

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By Steve Kral

As the current boom in the global mining industry rumbles on, mining companies have had to step up their efforts to replace mined reserves. Many of the majors are replacing and adding to their reserves and resources through acquisitions. This situation has allowed junior mining and exploration companies to do what they do best. They have been re-examining once uneconomic gold, copper and other metals properties with an eye to partnering with a major to develop them. And mines that have been closed for years due to poor economics are being given another look.

Jan 1, 2006

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003