Search Documents

One of the main bottlenecks in the carbon-in pulp process for the recovery qf gold is the elution procedure, which typically requires the heading of caustic cyanide eluants to high temperatures for 16 to 24 hours. The present work demonstrates that sodium sulphide solution as an alternative eluant can effect complete elution in about 4 hours at ambient temperatures. Elution efficiencies of around 100 per cent were obtained in 4 hours with a single pass of eluant containing 0,2 M Na2S and 0,4 NaOH about 10 bed-volumes of eluant The initial rate was slow over the first hour of elution, probably because the activated carbon catalysed the oxidation of sulphide to polysulphide. Elution efficiencies of around 100 per cent were also obtained in less than 4 hours during the batch elution of carbon at liquid-to-solid ratio of about 100. Lower liquid to solid ratio resulted in the re-adsorption of gold, probably owing to the oxidation of sulphide to polysulphide, with the resultant formation of gold complexes that were eluted less readily. Improved rates of elution were obtained at higher sulphide concentrations and pH values greater than about 13. Higher temperatures increased the initial elution rate, but lowered the overall extraction efficiency, probably because of the deposition of elemental gold on the carbon. Variation of the ionic strength by the addition of NaCl had no defect on the elution, which confirms that the elution mechanism in the case of sulphide is different from that when cyanide or I1)1droxide is used as the eluant. It is proposed that the elution of gold by sulphide solutions proceeds by means of an initial step that involves the reaction of polysulphide ions with the adsorbed aurocyanide speeds, forming AuCN on the carbon and thiocyanate in solution. This step is followed by the formation of poorly adsorbed complexes with sulphide ions, such as [AUS3-2]-The presence of polysulphides, whether generated in situ by the catalytic oxidation effect of activated carbon or by the addition of elemental sulphur, reduces the elution rate and efficiency dramatically. This is probably due to the formation of complexes such as AUS-3 and AUS-2 , which have a high adsorption affinity.

Jan 1, 1994

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

Ninth International Symposium TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of 14th to 19th June, 1970, follows the Computer Symposium held in Salt Lake City in September, 1969. The purpose of the Symposium is to define the role of decision-making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-have permitted us to structure it in such a way that a complete picture of the mineral industry in its public policy, corporate, financial and technological environment emerges. Topics for the sessions are: . The Public Policy Environment;. The role of Decision Making Techniques in the Mining Company; . Information Storage and Retrieval; . Markets-Forecasting, Patterns and Strategies;. Search for Mineral Deposits;. Quantification of Geological Variables;. The Mine Development Decision; Production Systems;. Planning, Scheduling and Control Systems. The sessions will be directed energetically by chairmen who have been in continuous contact with the authors, providing them with information about related papers and sessions. This symposium is sponsored by the Canadian Institute of Mining and Metallurgy, McGill University and Ecole Polytechnique. Further information may be obtained from: The 9th International Symposium. W. H. Gauvin, General Chairman, J. Elbrond, Programme Chairman. Department of Mining Engineering, Ecole Poly technique, P.O. Box 501, Snowdon, Montreal 248, Quebec, Canada. ACHEMA 1970 The European meeting of Chemical Engineering and the Achema Congress 1970 is being held at Frankfurt/Maine, from 17th to 24th June, 1970. The programme includes some 110 plenary and specialised lectures, numerous technical films, excursions, and technical discussions in front of the exhibits which form the central feature of the Achema-Exhibition Congress. Further information may be obtained from the honorary representative of Achema in South Africa, Mr F. Schilling, P.O. Box 31274, Braamfontein, Johannesburg. NINTH COMMONWEALTH CONGRESS PROCEEDINGS Publication of the proceedings of the Ninth Commonwealth Mining and Metallurgical Congress, 1969, is being undertaken by the Institution of Mining and Metallurgy, London. There will be four volumes covering papers presented at the Congress together with the discussion and author's replies, and the addresses by Sir Duncan and Sir Ronald Prain. These will be available April-June 1970. Special pre-publication prices apply to orders received before 1st April, 1970. Order forms may be obtained from Secretary S.A.I.M.M., P.O. Box 1183, Johannesburg. 6th World Congress on the Prevention of Occupational Risks This Congress, dealing with industrial accidents and occupational diseases, will be held in Vienna from 10th to 15th May, 1971. Further information may be obtained from: VI Weltkongress für Unfallverhütung, Postfach 745, A-1015 Wien, ÖSTERREICH. International Vacuum Metallurgy Conference 1970 The Vacuum Metallurgy Division of the American Vacuum Society is organizing an international meeting that will be held at the Convention Center in Aanaheim, California from 15th to 19th June, 1970. Enquiries should be directed to the Arrangement's Chairman, L. M. Bianchi, TRW Inc., 23555 Euclid Avenue, Cleveland, Ohio 44117, Tel. No. (216) 383-2111. AIME WORLD LEAD-ZINC SYMPOSIUM This symposium is being held from 21st to 23rd October, 1970, in St. Louis, Missouri, U.S.A., in conjunction with the Fall Meeting of the Society of Mining Engineers, and a Rapid Excavation Conference. In addition to local field trips to smelter and refinery operations there will be a number of extended trips of six to eight days. Information may be obtained from: Mr. John C. Fox, Secretary, Society of Mining Engineers of AI.M.E., 354 East 47th Street, New York, N.Y. 10017, U.S.A. NEW SUBSCRIPTION RATE TO THE JOURNAL As from 1st JANUARY, 1970, the subscription rate for the Journal has been increased from R12.00 to R18.00 per annum, i.e. R1.50 per issue instead of R1.00. The discount to booksellers is 15 per cent. COURSEOF THE THEORYOF THE UNIT OPERATION OF GRINDING The South African Institute of Chemical Engineers is arranging for Prof. L. G. Austen to conduct a course on the above subject in September, 1970. Interested persons should contact Dr G. S. Harrison, S.A. Institution of Chemical Engineers, A.E. & C.I., 15 Anderson Street, Johannesburg. METRICATION The S.A. Bureau of Standards has published a document entitled "Metric Scales and Units for use in the Building and Construction Industry." It has been compiled by the Metrication Committee of the National Building and Construction Advisory Council and is the first of the series of informatory documents relating to the programme for the metrication of the Building Act Construction Industry. This document is obtainable from the South African Bureau of Standards, Private Bag 191, Pretoria at 50c per copy.

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

1. Book review Economics of mineral exploration in Australia, by Brian W. Mackenzie and Michel L. Bilodeau. Australian Mineral Foundation (Private Bag 97, Glenside, South Australia 5065). 198pp. $A58. $A45 for students. Reviewer: D.G. Krige 2. Recent publications Combustion of coal liquid mixtures, by G.F. Morrison. London, lEA Coal Research, 1983, 52 pp. Hafnium: physico-chemical properties of its compounds and alloys. Vienna, International Atomic Energy Agency, 1981. 408 pp. 620 Austrian schillings. Canadian mines handbook 1984-85, edited by CD. Gardiner. Toronto, The Northern Miner, 1984. 500 pp. $24. Drilling equipment in Canadian mining and exploration- opportunities for the industry, by AJ. Jakubek. Toronto, Micromedia Limited (144 Front Street, Toronto M5J IG2, Canada), 1984. Research report 1984. Port Melbourne, Division Mineral Chemistry, Commonwealth Scientific and Industrial Research Organization, 1984. 190 pp. Surface engineering Wear is an unavoidable problem in virtually all products of the engineering industry, from the minute bearings of instruments to the cutting surfaces of earth-moving plant. Safety in mines About 50 papers will be presented at the 21st International Conference of Safety in Mines Research Institutes at Sydney from 21st to 25th October, 1985. Some 250 delegates from 30 nations are expected to attend. Professional development seminars March 18th-21st, 1985 Underground Blast-hole Mining May Ist-3rd, 1985 Mineral Processing of Gold Ores May 6th-10th, 1985 Mineral Comminution Systems May 13th-15th, 1985 Processing of Metallurgical Residues Analytical chemistry The Second Symposium on Analytical Chemistry in the Mining, Exploration and Processing of Materials is to be held in Pretoria from 15th to 19th April, 1985.

Jan 1, 1985

O.F.S. Branch Proceedings of the Annual General Meeting Held on Wednesday, 4th August, 1976 Mr G. J. C. Young (Chairman) was in the Chair. Also present was Dr R. E. Robinson, President of the South African Institute of Mining and Metallurgy. NlM reports Report no. 175 Copper extraction by leaching magnetites from Palabora Mining Company. (12th Apr., 1967; re-issued Jun. 1976) Report no. 1632 A mineralogical examination of beach-sand concentrates from a pilot plant at Richards Bay. (20th May, 1974; re-issued Jun. 1976.) Report no. 1825 The full automation of a Philips 1220 X -ray spectrometer. A Philips 1220 X-ray spectrometer (semi-automatic) Report no. 1840 The spectrophotometric determination of total uranium in silicate ores and leach liquors by use of bromo-PADAP. Report no. 1841 The determination of aC1;d-soluble uramum in silicate ores and solutions. AS & TS National Award The Associated Scientific and Technical Societies of South Africa has decided to make two National Awards this year. These awards, given in recognition of outstanding contributions to science and the application of science, will be made to Dr T. L. Wadley for his invention of the Tellurometer system of distance measurement and to Mr H. Scheffel for his design of the High Stability Bogie. Treatment of waste water A major international symposium, organized jointly by the Water and Environment Group of the Society of Chemical Industry and the Environment Group of The Chemical Society of London, will be held in London in 1977. Down-the-hole drilling Atlas Copco announces the publication of a revised and enlarged version of one of the booklets in their series 'Mining and Construction Methods'. This 40-page booklet is entitled 'Down-the-hole drilling with COP drills'.

Jan 10, 1976

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMC's (now BHP Billiton's) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By N. X. Feng, S. G. Zhou, X. L. Wu, J. P. Peng, Y. Z. Di

"Szaibelyite–suanite type ore is rich in magnesium oxide and boron oxide. We propose a new method to extract both metallic magnesium and valuable residues rich in boron by reduction using metallic aluminium.Thermodynamic analysis of the reactions between aluminum and MgO, Mg2B2O5, and Mg3B2O6 was carried out. The effects of CaF2 addition, temperature, mass of Al, and pellet formation pressure on the extraction of magnesium were also investigated experimentally.The results indicate that the magnesium oxide phase can be displaced from 2MgO-B2O3 and 3MgO·B2O3 by CaO in the reduction system. The reduction ratio of magnesium oxide was 38% without calcium fluoride addition, increasing to 94% with 5.1% calcium fluoride. The reduction ratio increased with increasing temperature and mass of Al. To obtain a higher reduction ratio, the reduction pellet should be formed under a reasonable pressure.IntroductionBoron and its compounds are widely used in textiles, borosilicate glass, metallurgy, fertilizers, and nuclear shielding. Boron resources are mainly found in Turkey, the USA, Russia, and China. In Liaoning, China, there are abundant szaibelyite–suanite type ores that are rich in magnesium oxide and boron oxide. Szaibelyite and suanite ores are used to produce borax by a carbon dioxide– soda process. Annually, 2 Mt of waste materials containing 3–20% B2O3 and 2–25% MgO are produced during the process. It is necessary to make use of these waste materials containing high concentrations of boron oxide and magnesium oxide to avoid environmental problems as well as for economic reasons (Ozdemir and K1pcak, 2007)"

Jan 1, 2016

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By M. Dworzanowski

The difference in the magnetic properties of minerals is the basis for magnetic separation. All minerals can be generally classified as ferromagnetic (strongly magnetic), paramagnetic (weakly magnetic) or diamagnetic (non-magnetic). Magnetic separation can be conducted dry or wet. The majority of the applications of wet magnetic separation in the mining industry are based on the wet drum magnetic separator. The wet drum magnetic separator has been in use for over 50 years and its design is based on a rotating drum installed inside a tank. Inside the drum are stationary, permanent magnets arranged in an arc to provide the magnetic field. These magnets can be of the ceramic ferrite type providing a low intensity magnetic field or of the rare earth type providing a high intensity magnetic field.

Jan 1, 2010

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By M. G. Atmore

As is usual when preparing for this type of occasion, I looked back at the subjects covered by my predecessors when they assumed the presidency of this Institute. You will appreciate that, in the eighty odd years since the Institute was founded, the diversity of subjects has been very great. In almost all cases it is quite natural that the speaker should have chosen a topic of special interest to him and one in which he was particularly knowledgeable.

Jan 1, 1979

By F. E. Steffens

The application of kriging in assessing the area rainfall in a weather modification experiment is complicated by the presence of many zero rainfall recordings on a given day, and the fact that the variograms seem to be quite different for the rainfall on different days. Indicator variograms are shown to be directly related to two sets of conditional probabilities. Probability kriging is used in estimating the probability of rainfall amounts above any cutoff at any point

Jan 1, 1987

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020

By M. B. Algeo

Discussion of the above paper M. B. ALGEO The management and staff of Buffelsfontein Gold Mining Company Limited are to be congratulated on the excellent performances described in the paper presented by Mr Christos. In this day and age, with the current economic and labour situation, the mining industry is being constantly pressed to increase the productivity of ever-diminishing quanta of resources. Stress in rock The ISRM Symposium, 1976 is to be held in Sydney from 9th to 13th August, 1976. It is being organized by The Australian Geo. mechanics Society as a regional symposium of the International Society for Rock Mechanics. Thermal analysis The First European Symposium on Thermal Analysis will be held at the University of Salford on 20th to 24th September, 1976.

Jan 12, 1975