Search Documents

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By L. Thomas, A. Argyn, B. Mbao, G. Longo Banza

Since the first application of solvent extraction as part of the hydrometallurgical processing of copper, several studies have been carried out to optimize extractant formulations. In 2006, Solvay developed the ACORGA® OPT series of solvent-extraction reagents to optimize copper transfer by use of a blended formulation containing both aldoxime and ketoxime as well as selected modifiers. The incorporation of selected modifiers in these blended reagents resulted in increased copper transfer, due to the interaction between the modifier and oximes within the blend. By changing the ketoxime concentration and ratio of modifier to aldoxime, the strength of the formulation was optimized to enhance copper transfer and improve Cu:Fe selectivity. This formulation is well known in the African region under the ACORGA® OPT5540 name and provides the best performance at the conditions of agitated leach plants with pregnant leach solutions that fluctuate in Cu grade and pH. This paper discusses advantages of using ACORGA® OPT5540 in the Copperbelt

Jan 1, 2023

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By K. -H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes become available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60%-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none-sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as uneconomic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid. Even though smelter gas is available at high SO2 concentrations, in a conventional acid plant one would add large amounts of air to dilute the gas down to a suitable concentration of 12?13 (14) %-vol. SO2. Dealing with higher SO2 concentrations in smelter acid plants is not feasible, as the gas exit temperature of the catalytic oxidation step would exceed the allowable limit for the catalyst. Hence those conventional acid plants are characterized by the use of large equipment, i.e. high capital cost, high energy consumption and limited flexibility. The newly developed LUREC® process can handle off-gas with significantly higher gas concentrations, even in excess of 25%-vol. SO2. It is entirely based on well-proven equipment and unit operations. The first industrial application, operating with 16?18%-vol. SO2 will be presented in this paper, along with the fundamentals of the process. It will be demonstrated that the process requires inherently lower capital cost, fewer operating costs, and offers better energy recovery and lower emissions as compared to conventional design. While most existing smelter acid plants would have some built-in spare capacity, any significant increase of smelter capacity, say of 30%, can basically not be accommodated without installing an additional parallel new acid plant unit. An add-on LUREC® module can remove any such restriction, while simultaneously debottlenecking the existing acid plant. The paper also discusses the present status of the add-on technology for smelter acid plant expansions with respect to technical boundary conditions of different process alternatives as well as economic and environmental aspects. Application of the LUREC® process to modern smelter acid plants operating with high SO2 gas concentration, will lead to a substantial reduction of the specific size of the gas processing equipment and equivalent savings in capital and operating cost. The LUREC® process is patented worldwide by OUTOTEC.

Jan 1, 2009

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009