Search Documents

By J. Petersen, T. Moyo, J. Dinga

The leaching of chalcopyrite in ferric sulfate media is notorious for its slow and inhibited kinetics. Different methods have been proposed to improve the kinetics, including the use of organic compounds as additives to the leaching media. In this study, the enhancing effect of methanol, ethanol, 1-propanol, and 2-propanol on the leaching of chalcopyrite in aerated acid ferric sulfate solutions using different reactor systems was investigated. The results revealed a clear improvement of copper dissolution by methanol and 1-propanol relative to tests with no additives under similar conditions. Operating a continuous-flow mini-column reactor yields surprisingly good results, potentially related to the maintaining of a consistent leaching micro-environment on the mineral surface. Scanning electron microscopy studies showed that the alcohols result in the removal of surface deposits formed during the anodic dissolution, potentially thus facilitating improved cathodic reduction of the ferric ion to drive the anodic dissolution.

Jan 1, 2023

By Z. Xingrong, L. Jiongtian, Z. Yangge, C. Yijun, L. Liang, H. Yangjia, H. Long

In this present research, a polymer poly (acrylamide-allyl thiourea) (PAM-ATU) with an average molecular weight 1.66 × 104 g/mol was used as a depressant in the flotation separation of molybdenite from chalcopyrite and galena. The micro-flotation experimental results showed that PAM-ATU exhibited a strong influence on the flotation performances of chalcopyrite and galena, but had little effect on that of molybdenite within a pH range of 9.0~11.0 at a dosage of lower than 6.0 mg/L. The flotation results of bulk flotation tests illustrated that PAM-ATU showed a stronger depression power than sodium thioglycollate (TGA) and sodium sulfide. The comparison results demonstrated that PAM-ATU and TGA had an advantage in reducing galena and chalcopyrite impurities in the molybdenum concentrate, respectively. With the combination of PAM-ATU and TGA, a good flotation separation result was achieved through one roughing operation where the recovery of molybdenum in the froth product was over 75.0%, while the recovery of copper and lead were less than 22.0% and 15.0%, individually. It was also found that a molybdenum concentrate with Mo grade of 46.32%, Cu grade of 0.16%, Pb grade of 0.06%, was obtained by a closed circuit flotation flowsheet of one roughing-three scavenging-five cleaning with a Mo recovery of 77.67%. Keywords: PAM-ATU, molybdenite, depressant, chalcopyrite, galena

Jan 1, 2020

By A. J. H. Newell, K. Doherty

A copper-gold project has required a number of trade-off studies underpinned by test work to settle on pragmatic flowsheets and throughputs to support a pre-feasibility study that provides a compelling financial case. The primary trade-off studies were based on the mine schedule, ore type feed-grade recovery relationships, likely concentrate grades and typical marketing terms as well as the estimated capital and operating costs for a range of throughputs and mining strategies. Secondary trade-off studies were conducted for specific circuits and additional processing options. Although the details of these studies are not presented, the technical options and subsequent flowsheets are discussed. While the flowsheets will be optimised during the feasibility study stage, the basis is now fixed for the four ore types that would be mined from the copper-gold orebody. The ore types, resulting from a strong weathering profile, exhibit a wide range of copper mineralisation and gold associations, as well as gangue types. They display a range of characteristics that necessitated a nuanced approach to flowsheet development. The primary separation techniques that have been employed include gravity, classification, flotation and leaching while a range of comminution methods have been selected to suit the properties of the ore types. While technical issues are important factors in terms of maximising the quality of separations, recoveries and revenues, attention to material handling, equipment characteristics, the mine schedule, and capital and operating costs are equally important considerations for settling upon a suitable and robust flowsheet. Keywords: Flowsheet, testwork, studies, saprolite gold, native copper, chalcocite, chalcopyrite

Jan 1, 2020

By V. Borissenkob, L. D. Ropera, M. J. Danielc

Eccentric High Pressure Centrifugal Comminution (eHPCC) is a novel comminution device that provides a single step to achieve a desired target grind size. The mechanisms within the unit mirror particle breakage that is akin to high-pressure-grinding rolls (HPGR) and high-intensity-attrition with air classification. eHPCC receives lump and can produce a product P80 such that the progeny are at or less than natural grain size of the feed. The unit operates in either closed or open-circuit. The grinding zone is dry and free of steel grinding media. This paper presents evidence of eHPCC-2 capable of selective and preferential mineral liberation. A recent test campaign on a blend of underground quartzgold- vein ore was completed. The feed to eHPCC-2 trial was SAG mill trommel oversize (low-grade pebble rejects). eHPCC-2 operated open-circuit with air-fluidisation in the rotating-grinding-chamber, classifying particles based on terminal velocity of the air-swept product particles, displaying size and mineral composition classification taking place at the same time. There is an opportunity for future industrial research targeting eHPCC as an advanced integrated comminution and classification technology. Keywords: High pressure, high intensity, compression, attrition, comminution, classification

Jan 1, 2020

By Y. Fu, C. Aldrich

This study investigates the use of dense convolutional neural networks to estimate bubble size distributions in flotation froths. 20 videographically captured images of froths from an industrial platinum flotation plant in South Africa were labelled semantically with an image annotation tool, LabelMe (https://github.com/wkentaro/labelme). As a result, pixels in the images could be categorized into three classes, namely ‘bubbles’ (class 0), ‘bubble boundaries’ (class 1) and ‘background’ (class 2). A U-net architecture with a ResNet34 backbone was trained to segment the images via classification of the pixels in the images. 5 of the 20 images were used to validate the performance of the neural network. Explicit inclusion of the bubble boundaries as a class proved to be significantly more effective than training the network with two classes only (i.e. bubbles and background). However, the thickness of the boundary layer regions were critical. If too thin, it was difficult to distinguish between some contiguous bubbles and if too thick, some fine bubbles may not be identified. The results were promising, although there is still significant scope for improvement, among other by making use of more images for training and validation. Keywords: Flotation Froths, Convolutional Neural Networks, Deep Learning, Bubble size Analysis

Jan 1, 2020

By S. J. Oosthuizen

This paper examines innovation in relation to the availability of anew material: the metal titanium. The paper aims to highlight the need for the inclusion of entrepreneurial innovation as a necessary focus area in the development of a titanium metal value chain. Both the Department of Science and Technology (DST) and the Department of Mineral Resources (DMR) have identified the creation of titanium metals production capabilities as a key growth area for South Africa. Using historical literature as a source of data, the activities of selected innovators who used titanium metal as a central component in their success, were investigated. The origin of the process innovation behind the titanium metals industry, and two titanium product innovations: namely, medical implants and sporting goods, were detailed as case studies. It was found that individual innovators were responsible for the creation, and rapid growth, of the titanium industry and titanium product applications. There is a need to link the current research and development into titanium metals production with individuals and organizations capable of commercializing innovative processes and products.

Jan 1, 2011

By C. Musingwini, M. Mohutsiwa

"SynopsisCapital cost estimates are important in decisions on whether a project will be approved, mothballed, or abandoned. In South Africa, junior coal miners do not have extensive databases of historical projects from which to estimate capital costs. The purpose of this paper is to establish formulae that can be used for estimating capital costs of developing coal mines in a coal-producing country, using South Africa as a case study. The costs are estimated to an error of magnitude level of -30% to +50%, which is suitable for a concept study level, using a parametric estimation technique. The study uses data from completed coal mining projects from selected coal-producing countries. Three formulae are developed and presented for estimating capital costs of underground bord and pillar, surface shovel and truck, and dragline operations.IntroductionCapital cost estimates play a critical role in deciding whether projects will proceed, be delayed, or abandoned. It is therefore important that capital cost estimates are carried out accurately as determined by the estimation guidelines based on the level of estimation conducted (Shafiee and Topal, 2012). The lack of literature on estimation of capital costs in many coal mining countries is adversely affecting junior coal miners, since they do not have an extensive database of historical projects on which to base estimations. In South Africa, the difficulty in estimating capital costs is attributable to lack of publicly available data on completed South African mining projects (Hall, 2013)."

Jan 1, 2015

By N. Naudé, J. de Villiers, C. P. Bergmann

It is proposed that the physical and chemical composition of individual mineral particles are an appropriate basis from which to model the performance of minerals processing equipment. Such a particle-based approach enables modelling across disciplines such as comminution, classification and flotation and automatically generates the traditional mass and chemistry balances. The general approach followed is to generate full grade-recovery curves for a separator by sampling product and tailings at varying mass yields. AutoSEM characterisation of each sample provides particle data that is used to reconcile mineral deportment and liberation to the measured size and assay data. In this way, partition surfaces can be generated and modelled. In this paper, an empirical model for the performance of a gravity spiral concentrator treating fine chromite ore is proposed. The model is based on the combination of two partition surfaces and is able to accommodate both forward and reverse gravity concentration effects per size fraction. The results show that this approach is well suited to represent spiral performance for the cases evaluated. The effect of two feed particle size distributions on the performance of the Multotec SC21 and SC25 spirals is demonstrated. Simulations are run in an Excel environment, linked to Python-enabled routines for enhanced data management and calculation speed. Keywords: Spiral concentrator, gravity separation, particle-based modelling

Jan 1, 2020

By C. Hsu

Underground coal gasification (UCG) is becoming more popular as the reserves of good quality, mineable coal are starting to diminish, and yet the global energy demand from coal is still increasing. The purpose of this research project was to investigate cavity formation within a coal block due to the combustion reactions in the context of UCG. The cavity plays a pivotal role in the UCG process, as it is essentially the gasification reactor. Cavity formation in an in situ gasification process using the forward combustion linking method (FCL) had been investigated, and a laboratory model was created to simulate the process. The experiment was performed by drilling a U-shaped tunnel into a coal block, which was then combusted internally with air that was fed through an injection hole. A heating element (at approximately 500°C) was used to supply the required heat for combustion at the base of the injection well. The coal blocks were analysed using micro-focus X-ray tomography. The tomography results showed that the coal tended to crack along the bedding plane after a short duration of combustion, due to either the formation of clinker or the expansion of swelling vitrinite along the horizontal tunnel. The deposit was thicker at the base of the injection well compared to the base of the production well; this may have been caused by the turbulence of the air flow and the relatively high oxygen concentration at the base of the injection well. A comparison of the results with work by Daggupati et al. (2010) showed the same trend, despite the slightly different methodology applied.

Jan 1, 2014

By M. S. Shishvan, J. R. van Duijvenbode

The results of dig limit delineation in open pit mining are never truly optimized due to gaps in the underlying data, such as insufficient sampling. Aside from the data uncertainty, there is also an influence on the final dig limit by either humans or by the heuristic character of an optimization method like simulated annealing. Several dig limit optimizers have been published, which can replace the manual dig-limits designing process. However, these dig limit designs are generally not adapted to account for this heuristic character. In this paper we present a stochastic analysis tool that can be used with the results of heuristic dig-limit optimization to increase confidence in the obtained results. First, an enhanced simulated annealing algorithm for dig limit optimization is presented. Then, this algorithm is tested on ten different blasts at the Marigold mine, Nevada, USA, as a case study. Finally, the results are analysed with a destination-based ensemble probability map and an analysis conducted of the final solution data distribution. The generated dig-limit designs of the algorithm include high revenue areas that are excluded in comparable manual designs and show improved objective and revenue values. The analysis tool provides block destination probabilities and box plots with the distribution of opportunity value for the dig limit. Furthermore, with the analysis tool, it is possible to make well-informed design decisions in areas of uncertainty.

Dec 13, 2022

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By I. J. Kotzé, R. T. Jones

Conventional PGM matte smelting requires the presence of a certain quantity of base metal sulphides in order to collect the platinum group metals in a molten sulphidic matte phase in the furnace. Furthermore, the quantity of chromium oxide in the feed materials is controlled in order to avoid the build-up of high-melting chromite spinels in the furnace. Mintek has developed a process for smelting difficult PGM-containing feed materials that contain low amounts of sulphur and/or high amounts of chromium oxide. A DC arc furnace is used to provide the appropriate conditions to generate an iron alloy that collects PGMs very effectively, leaving extremely low residual quantities of PGMs in the slag. Various feed materials have been treated successfully in furnace campaigns running at power levels up to 1.5 MW. The longest of these campaigns was run continuously for more than four months, treating more than two thousand tons of materials such as low-grade concentrates, revert tailings, and converter slag. The campaigns demonstrated the robustness and versatility of the process, and proved that it is possible to sustainably produce a PGM-containing alloy and discardable slags containing an average of less than 1.4 g/t of PGMs over the entire campaign. Keywords: DC arc, smelting, furnace, platinum, PGM, revert tailings, converter slag, ConRoast

Jan 1, 2004

By M. Shamsi, M. Nehring

One of the most challenging aspects in semi-mobile in-pit crushing and conveying (SMIPCC) system design is determining the optimum depth at which to change from a purely truck-based haulage system to a conveyor-based haulage system. We used scenario analysis to determine the optimum transition depth between a truck and shovel (TS) system and a SMIPCC system. Traditional pit-limit algorithms were used to generate the final pit limit on a copper deposit, which was then divided into four pushbacks. The final operating pushbacks (phases) were designed for both TS and SMIPCC. The end depths for each phase are viewed as candidate transition points to switch from the TS to SMIPCC haulage system. Economic calculations were applied for five different scenarios, including adopting SMIPCC from the outset (pure SMIPCC), after the first, second, and third phases, and finally not using the SMIPCC system (pure TS) at all. The analysis indicates that the second scenario, at a depth of 335 m, results in the lowest cumulative discounted cost (CDC). In this case, the CDC is 17.6% lower than that for the pure TS scenario and 10.7% lower than for the pure SMIPCC system scenario.

Sep 1, 2021

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

By L. W. Palmer

Compositing or regularization of drillhole data is common practice in mineral resource estimation and is deemed a necessary step in producing unbiased estimates of mineral resources and reserves. Commonly, data are collected over irregular distances due to the varying relative thicknesses of lithologies drilled or sampling/assaying strategies. This necessitates data transformation to regular lengths of equal size to ensure that all data have the same sample support. However, there have been few detailed publications on the effect of this process on the composited data that are subsequently taken forward for the estimation process. In this paper, three currently available compositing methods are reviewed and the effects of inappropriate compositing methodologies presented. It is shown through a case study that compositing samples to different lengths leads to changes in the average and variance of the grades in the drillcores in the dataset, which will impact the final estimated value. These differences are exacerbated by breaks or gaps in data where, for a variety of reasons, there has been no data collection or data have been lost. The importance of appropriately treating blank and zero data is also presented. Globally, these differences might be minimal, but locally may be substantial, affecting the efficiency of the estimation and subsequent use of the results in, for example, mine planning and reconciliation. Further detailed investigation of compositing practices is required if the full implications of compositing are to be understood and any induced bias effectively defined.

Jul 10, 2024

By T. Khumalo, L. Musenwa, S. Masemola, M. Kgaphola

"In 2017, Petra Diamonds completed the construction and commissioning of a modern, fit-for-purpose diamond processing plant at Cullinan Diamond Mine (CDM). The design of CDM’s milling circuit is unconventional in that it comprises an autogenous (AG) mill with a grate discharge with large ports, low-revolution jaw crushers, and high-pressure grinding roll crushers with large operating gaps. In this paper we review the design to provide guidance on what is expected from the milling circuit and to demonstrate how the design aims to address challenges experienced in the old plant, which was based on staged crushing technology. We assessed the performance of the CDM AG milling circuit from commissioning and early production stages to examine its impact along multiple dimensions. In the assessment we sought to understand the lessons from our milling circuit regarding diamond liberation, energy consumption, and the future of diamond processing as a whole. IntroductionCullinan Diamond Mine (CDM), previously known as Premier Mine, is an underground diamond mine owned by Petra Diamonds. Petra Diamonds is a leading independent diamond mining group and a growing supplier of rough diamonds to the international market. Petra Diamonds is listed on the Main Market of the London Stock Exchange under the ticker ‘PDL’. Petra’s total resource of 305 million carats ranks third by size after De Beers and ALROSA (Petra Diamonds, 2018).CDM was established in 1902. The mine rose to prominence in 1905, when the 3106 carat Cullinan Diamond — the largest rough diamond of gem quality ever found — was discovered there. The mine has produced over 750 stones that are larger than 100 carats and more than a quarter of all the world's diamonds that are larger than 400 carats. Cullinan is renowned as a source of large, high-quality gem diamonds, including Type II stones, as well as being the world’s most important source of very rare blue diamonds (Petra Diamonds, 2018)."

Feb 1, 2019

By M. B. Shongwe, G. Freemantle, M. Botha, S. Brill, J. D. Steenkamp

During steelmaking, one important factor for production efficiency is the free opening of the ladle nozzle during continuous casting. Free opening occurs when the well filler sand and the steel flow freely when the slide gate is opened. Well filler sands are used for the slide gate of a ladle to separate the slide gate refractory and the molten steel. The well filler sand is partially sintered by the heat of the molten metal, which can result in the ladle nozzle failing to open if the sand is not sintered to an appropriate extent. It is therefore of great importance that the sintering behaviour of well filler sand is understood. We studied the effect of the well filler sand chemistry on its sintering properties. Samples of well filler sand with various chemical compositions were sintered in a high-temperature chamber furnace. Quantitative X-ray diffraction (XRD), inductively coupled plasma optical emission spectrometry (ICPOES), and wavelength dispersive spectrometry (WDS) by electron microprobe analysis (EMPA) were used to analyse the various well filler sand mixes. Points of analysis were indicated on backscattered electron (BSE) micrographs. Quantitative element mapping was undertaken by energy dispersive spectrometry (EDS). Thermodynamic calculations in FactSage predicted the percentage liquid phase present for the various well filler sand compositions at equilibrium conditions. The results of this work show that the degree of sintering of chromite-silica well filler sand depends strongly on the silica content. The amount of liquid phase formed increases with increasing silica content.

Feb 2, 2022

By K. R. Koch

Although some of the platinum(II/IV) and rhodium(III) chemistry is considered ?old? and well-known, the application of modern multinuclear NMR spectroscopic methods to this chemistry in solution reveals new details about their rich and relevant solution chemistry. In this paper we will briefly illustrate that the highly-sensitive 195Pt NMR shielding is an excellent probe to explore aspects such as solvation, ion-pairing, and the hydrolysis chemistry of inter alia [PtCl6-n(H2O)n]n-2 (n=0-5). Moreover the novel use of 35Cl/37Cl and 18O isotopes effects as unique NMR ?fingerprints? leading to a new and unambiguous method of chemical speciation of the numerous possible PtII/IV and RhIII complexes present in halide-rich aqueous solutions. In the case of Rh(III) chemistry a new, direct speciation distribution diagram has been established for [RhCln(H2O)6-n]3-n complexes (n = 3-6) in HCl solution at 292 K with these methods.

Jan 1, 2012

By W. H. Holtzhausen

The purpose of this project was to compare two underground, batch coal haulers ? battery haulers and shuttle cars ? in order to determine the more viable machine to implement. The specific standards for battery haulers were investigated and compared to the requirements of shuttle cars in order to identify the unnecessary expenses related to the legal requirements that are attached to the machines. Costs such as running costs, capital costs, and maintenance costs were researched and compared over a typical life of machine. Average production rates and breakdown times were obtained and used to determine which machine would be more reliable in achieving the required annual production.

Jan 1, 2014

By M. Rhodes

The Sukari project, which is owned by Centamin Egypt Ltd, is located in southern Egypt, 770 km south of Cairo but close to the Red Sea. The project is the first new gold development in Egypt and was commissioned in the middle of 2009. In 2007, Centamin purchased the CIL plant from the Kori Kollo mine in Bolivia. This plant was originally designed to treat 6.5 Mtpa of oxide ore. The Sukari deposit contains an oxide zone close to surface with a thick zone of mixed oxide and sulphides below this. The sulphides contain relatively coarse pyrite and arsenopyrite with fine <10 µm gold inclusions. Eventually, the sulphide ore will be mined from underground. Metplant Engineering Pty Ltd, a subsidiary of Bateman Engineering Pty Ltd was contracted to design modifications and additions to the Kori Kollo plant to enable it to treat the Sukari ores. The plant was designed to treat the three ore types in stages. Throughput was set to 4 Mtpa, dueto Sukari ore being harder, at a head grade of 1.7 g/t to produce 200 000 oz of gold. The oxide circuit was based on the use of the Kori Kollo plant and the difference with mixed ore was that the oxide circuit would treat flotation tailings rather than ore. This circuit has a leach capacity of 26 000 m3 and residence time of 24 hrs The main feature of the upgraded mixed ore plant was the addition of a flotation circuit to produce a concentrate which would be reground and treated in a separate leach and elution circuit. Ore is crushed in a gyratory crusher and the comminution circuit uses a conventional SABC producing a product with a P80 of 150 microns. The throughput of 580 tph of oxide ore and 500tph of mixed ore was set to match the mills from Kori Kollo, with the addition of the pebble crusher to accommodate the more competent Sukari ore. The flotation circuit comprises a single rougher circuit to maximize recovery. The concentrate is thickened prior to regrinding which is carried out in a tower mill and two SMD mills operating in series. The final product, with a P80 of 12 microns, from the regrind circuit is leached in a CIL circuit with a total capacity of 2 550 m3. Gold is recovered through a conventional pressure Zadra circuit. Tailings from both circuits report to separate tailings thickeners and are pumped to a tailings storage facility. The circuit is designed to maximize the recovery of water. The project lies in one of the driest deserts in the world and a feature of the operation is the use of sea water from the Red Sea. This water is pumped 25 km from the coast.

Jan 1, 2009