Search Documents

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By L. Diko-Makia, N. Rembuluwani

Artisanal and small-scale mining is crucial for the mineral sector in South Africa, but it also presents both opportunities and challenges. This paper presents an overview of the South African artisanal and small-scale mining sector, the socio-economic significance of artisanal and smallscale mining, the regulatory environment, and the environmental impacts, which are currently the status quo of this sector in South Africa. The paper identified ways in which artisanal and small-scale mining can support local development, create employment opportunities, and reduce poverty. The case of informatisation, ecological damage, and social insecurity has shown social conflicts, potential land degradation, and criminal behaviour. Finally, the paper discusses the future of artisanal and small-scale mining in South Africa, which will largely depend on improved legislation, enhanced personnel capacity, and more sustainable practices to ensure that the positive outcomes of the industry outweigh the negative ones. These propositions include recommendations to all stakeholders, including the government, industry, and civil society, such as stricter environmental regulations, improved working conditions for miners, and the promotion of responsible mining practices.

Dec 15, 2025

By M J. Daniel

The diamond industry is no newcomer to High Pressure Grinding Rolls (HPGR) as it has used the technology for more than 20 years, predominantly in secondary crushing and recrushing roles. In fact it could be argued that the diamond industry has led the way for the wider minerals industry to consider its application. In existing conventional secondary cone crushing applications, large valuable diamonds are" won" through meticulously managing the recovery process within defined particle size ranges. Conventional crushers operate with relatively large closed side settings, but have the potential to damage diamonds by making direct contact with the sides of the crusher. Cone crushers also result in steep product size distributions that run a high risk of losing many of the smaller, unliberated but more abundant diamonds from the rock. This current comminution paradigm of particle size reduction management results in recrushing processing applications or plants where HPGRs are often used.

Jan 1, 2010

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By A. P. I. Popoola, D. O. Okanigbe

Copper smelter dust (CSD) is a byproduct of copper smelting and is composed of considerable amounts of copper values and also contaminants (like silica and mullite). Silica in CSD forms Siloxane, a low density material, which is difficult to separate from the aqueous phase during solvent extraction. The need therefore arises to reduce/remove the aluminosilicates for better grade and recovery of copper in subsequent processes. This paper reports the use of two types of centrifugal gravity concentrators, namely Knelson (KGC) and Falcon (FGC), for upgrade of copper in CSD. The aim was achieved by an initial characterisation (Particle Size Distribution (PSD) and mineralogical analysis), together with Density Separation (DS) experimentation, premised on a hypothetical density difference between copper oxide and silicon/aluminum oxide. Wet screening results showed that 88.52 % of CSD particles were in -53 μm fraction. Further PSD study using laser diffraction showed the -53 μm fraction to be composed mainly of 26 μm, 22 μm and 18.5 μm fractions. Mineralogical analysis showed copper to occur mainly as oxides (24.34 wt%), but also as sulphides (7.95 wt%), and a substantial amount of aluminosilicates (42.97 wt%) were identified. Density of CSD was determined as 2.83 g/cm3. Copper content (18.02 wt%) in CSD was upgraded to 35.94 wt% in concentrate using KGC. In conclusion, the results showed good convergence between hypothesis and experiment. Additionally, it was also concluded that KGC performed better than FGC for copper upgrade in CSD. However, roasting CSD prior density separation was recommended for enhanced copper upgrade. Keywords: Copper smelter dust, density separation, solvent extraction, mineralogy

Jan 1, 2020

By C. Zangerl, K. F. Evans, S. Loew

ABSTRACT: Settlements above fractured crystalline rock masses are rarely observed and in the past, geotechnical engineers would not expect substantial subsidence to occur in association with a deep tunnelling project. However, recent high precision levelling measurements along the Gotthard pass road in central Switzerland, have revealed up to 12 cm of subsidence along sections that pass several hundred metres above the Gotthard highway tunnel. Large-scale consolidation resulting from tunnel drainage and pore pressure changes in the rock mass are believed to be the contributing mechanism. This paper presents results from an extensive numerical modelling study focussing on the processes responsible for this subsidence. Results derived from 2-D discontinuum (i.e. distinct-element) and continuum (i.e. finite-element) modelling show that both discrete fracture deformation (i.e. fracture closure and shear) and poro-elastic consolidation of the intact rock matrix equally contribute to the observed magnitudes and shape of the surface subsidence trough. RÉSUMÉ: Des tassements aux dessus de massifs cristallins sont rarement observés et par le passé les géotechniciens ne prévoyait pas de subsidence significative associée avec des projets de tunnel profond. Cependant, de récentes campagnes de nivellement haute précision le long de la route du Col du Gotthard (Suisse centrale), ont mis en évidence des subsidences atteignant 12 cm sur des sections passant plusieurs centaines de mètres au-dessus du tunnel routier du Gotthard. Le mécanisme invoqué pour expliquer ce phénomène est la consolidation à grande échelle due au drainage du tunnel et aux variations de pression de pore dans le massif rocheux. Cet article présente les résultats d’une modélisation numérique intensive mettant l’accent sur les processus responsables pour la subsidence. Ces résultats obtenus grâce à des modèles 2-D discontinus (p. ex. éléments distincts) et continus (p. ex. éléments finis) montrent que la déformation sur des fractures discrètes (fermeture de fractures, cisaillement) ainsi que la consolidation poro-élastique de la roche intacte contribuent également aux magnitudes et aux géométries de subsidence observée en surface. ZUSAMMENFASSUNG: Beachtliche Oberflächensenkungen in einem kristallinen Gebirge, deren Ursache im Vortrieb eines mehrere hundert Meter tiefgelegenen Tunnels liegt, wurden bisher nicht erwartet und beobachtet. Dennoch wurden nach dem Bau des Gotthardstrassentunnels, entlang der Gotthardpassstrasse Oberflächensenkungen mit einem Maximalbetrag von 12 cm bei der Auswertung von Präzisions-Nivellements entdeckt. Dieser Maximalbetrag wurde in einem granitischen Gneis gemessen. Die örtliche Übereinstimmung zwischen dem maximalem Senkungsbetrag und dem maximalem Wasserzufluss zum Tunnel, und die zeitliche Abfolge von Tunnelbau und auftretenden Oberflächensenkungen lassen hydromechanisch gekoppelte Prozesse als Ursache dieser Gebirgsverformungen vermuten. In dieser Arbeit werden die Ergebnisse ausgedehnter prozessorientierter numerischer Simulationen präsentiert. Resultate aus den 2-D Diskontinuum (d.h. distinct-element) und Kontinuum (d.h. finite element) Simulationen zeigen, dass beide Verformungsmechanismen, d.h. an diskreten Brüchen und der intakten Gesteinsmatrix, gleichbedeutend für die beobachteten Senkungsbeträge und der Form des Setzungstroges verantwortlich sind.

Jan 1, 2003

1. New publications International minerals/metals review - 1982. Washington D.C., McGraw-Hill, 1983.720 pp. U.S.$1l7. Mining subsidence engineering, by Helmut Kratzsch. New York, Springer, 1983.580 pp. U.S. $63,20. Papers presented at the 6th International Symposium on Jet Cutting Technology, Guildford, England: April 6-8, 1982, edited by H. S. Step hens and E. B. Davies. Cranfield (England), BHRA Fluid Engineering, 1982. £40. 2. Mintek reports Report M95 Modern applications of polarography and voltammetry to inorganic analysis. Report M96 The mathematical modelling of the reduction behaviour of chromite from the Upper Chromitite Layer of the Bushveld Complex. Report M113 The selective flotation of South African chromite. Conference on copper The International Conference &apos;Copper 83&apos;, to be held in London on 1st and 2nd November, 1983, will provide a valuable forum for all connected with the manufacture and use of copper. Underwater mining The 14th Underwater Mining Institute will be held in Madison, Wisconsin, on 7th and 8th November, 1983. Asian mining The Institution of Mining and Metallurgy, in conjunction with the Chamber of Mines of the Philippines, will hold an international conference, Asian Mining &apos;84, in Manila, Philippines, from 6th to 8th November, 1984. Apcom &apos;84 The Eighteenth International Symposium on the Application of Computers and Mathematics in the Minerals Industries will be held in London in the week 26th to 30th March, 1984. The Symposium is being Jet cutting Another Symposium on the very successful and popular series of international conferences on Jet Cutting Technology is being arranged by BHRA.

Jan 1, 1983

By Y. Mitani, M. Zhang, M. Takeda, T. Esaki

Despite their inadequacy, assumptions of isotropy and homogeneity are often applied to the analyses of in situ permeability tests. In this paper, we exam the effects of anisotropy and heterogeneity on Pressure Pulse Test (PPT) and Constant Head Injection Test (CHIT) by means of numerical approaches. Some new findings that offer practical considerations in properly interpreting in-situ permeability tests are presented. Malgré leur manque de précision inhérente, les assomptions d&apos;anisotropie et d&apos;hétérogénéité sont souvent utilisées lors de test de perméabilité in situ. Dans cette étude, nous examinons les effets de l&apos;anisotropie et de l&apos;hétérogénéité sur le test par pression pulsée et le test à injection à charge hydraulique constante par le biais de la simulation numérique. Des nouveaux résultats permettant une interprétation pratique et claire des test de perméabilité in-situ sont présentés. Trotz ihrer inhärenten Ungeeignetheit werden häufig Annahmen über Isotropie und Homogenität auf Analysen von in-situ Permeabilitätstests angewendet. In diesem Papier untersuchen wir die Effekte von Anisotropie und Heterogenität auf Durck-Impuls-Test (PPT) und Konstant-Kopf-Einspritztest (CHIT) mit numerischen Ansätzen. Einige neue Befunde, die zu praktischen Erwägungen zur richtigen Interpretation von in-situ Permeabilitätstests führen, werden vorgestellt.

Jan 1, 2003

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

By D. Clement

A comparison between hydraulic and pneumatic rockdrills by D. CLEMENT The regulation of compressed-air reticulation systems is very poor compared with that of electrical systems; this means that electrohydraulic rockdrill systems offer greater flexibility, additional power being readily available at the working face. Hydrometallurgy A new journal devoted to all aspects of the aqueous processing of metals is scheduled to appear this year. Entitled Hydrometallurgy, the journal will be published in quarterly issues, one volume per year. Mineral dressing Contributions are invited for the Symposium on Recent Progress in Mineral Dressing in South Africa, which is to be arranged jointly by the South African Institute of Mining and Metallurgy and the National Institute for Metallurgy. Mineraalbereiding Bydraes word verlang tot die Simposium oor Onlangse Vordering met Mineraalbereiding in Suid-Afrika wat gesamentlik deur die Suid- Afrikaanse Instituut vir Mynbou en Metallurgie en die Nasionale Instituut vir Metallurgie gereel gaan word. Rock mechanics The Sixteenth Symposium on Rock Mechanics is to be held at the University of Minnesota from 22nd to 24th September, 1975. The Symposium is the official Symposium for 1975 of the International Society for Rock Mechanics (I.S.R.M.), and the Council for I.S.R.M., consisting of members from 25 countries, will meet during the Symposium. Powder metallurgy The annual meeting on powder metallurgy organized by The Metals Society is this year to be held at the Stratford Hilton Hotel, Stratford-upon-Avon (the notification did not include the date of the meeting). Vacation School The South African Institute of Mining and Metallurgy has great pleasure in announcing its intention of holding a vacation school on the topic of electric-furnace melting. NIM reports Report no. 1681 The determination of sulphur and phosphorus in chromite. Report no. 1687 The viscosities and electrical conductivities of slags associated with the production of high-carbon ferromanganese alloys.

Jan 3, 1975

By E. Matinde

Poor phase separation and fine dissemination of the desired components within congruous slag phases are key challenges limiting the recoverability of values from slags by conventional beneficiation methods. Slag microstructure conditioning is a pragmatic approach to increasing themvalue-in-use of discard slags, especially when integrated with the broader smelter infrastructure. Although not yet tested on oxide slag systems, this paper explores the potential application of magnetohydrodynamic principles to the crystallization behaviour of bulk slags. Integrating the slag microstructure conditioning infrastructure to the existing smelter infrastructure is key to unlocking the economic value of slags because it is most economic to condition the properties of molten slag directly after tapping. A new business model that integrates smelting units to transversalmeconomic activities, such as cement production and suppliers of construction aggregates, canmsignificantly increase the circularity of metallurgical slags.

Oct 9, 2024

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By Y. P. Shoupletsov

ABSTRACT. A retrospective analysis of some geomechanical classifications for rock masses is presented. It is shown that estimates of rock mass strength according to geomechanical classifications developed, e.g., for construction of tunnels and for ore mines can differ very much. Development of specifically oriented classifications for rock masses with certain geomechanical properties is required. ZUSAMMENFASSUNG. Es wurde eine retrospektive Analyse einiger geomechanoschen Klassifikationen von Gesteinsmassiven durchgefuhrt. Es idt aufgezeigt worden, dass die Bes-timmung der Festigkeit des Massivs nach geomechanischen Klassifikationen, die z.B. fur den Bau von Tunnelen und fur Erzbergwerke entwickelt wurden, sich um etliche Male unterscheiden kann. Es ist eine Entwicklung von spezialisierten Klassifikationen fur Gesteinsmassive mit bestimmten geomechanischen Eigenschaften erforderlich. RESUME. Il a ete fait l’analyse retrospective de certaines classifications geomecaniques des massifs de roche. Il a ete montre que les estimations de solidite du massif suivant les classifications geomecaniques etudiees, par exemple, pour la construction des tunnels et pour les puits de minerai peuvent differer en quelques fois. Il est donc necessaire d’etudier les classifications specialisees pour les massifs aux proprietes geomecaniques particulieres.

Jan 1, 2003

By G. Akdogan, Q. G. Reynolds, S. J. Baumgartner

A computational model of a submerged arc furnace (SAF) used in the production of ferrochrome is presented. The model‘s intended use is to investigate the extent to which intrinsic and extrinsic properties of the raw materials affect burden distribution and electrical resistance within the furnace. The model is built on the discrete element method and calculates the mechanical interactions of particle distributions resulting from the flow motion of typical raw materials used in the smelting of chromium ore. This model excludes the effects of thermodynamics, furnace chemistry, and heat transfer. It illustrates how the consumption of materials (chromite pellets, flux, and reductant) is affected by changes in electrode length, reductant fractions, and reductant sizing and density during the formation of a reductant bed. The resistance calculation algorithm developed by Mintek was applied to construct networks developed from particle contacts, which can quantitatively generate estimates of the electrode-to-electrode and electrode-to-bath electrical conduction conditions.

Apr 16, 2024

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By Y. H. Hatzor

ABSTRACT: A fully dynamic, two dimensional, stability analysis of a highly discontinuous rock slope is demonstrated in this paper. The studied rock slope is the upper terrace of King Herod’s Palace in Masada, situated on the western margins of the seismically active Dead Sea Rift. The dynamic deformation of the slope is calculated using a fully dynamic version of DDA in which time dependent acceleration is used as input. The analytically determined failure modes of critical keyblocks in the jointed rock slope are clearly predicted by DDA at the end of the dynamic calculation. It is found however that for realistic displacement estimates some amount of energy dissipation must be introduced into the otherwise fully elastic, un-damped, DDA formulation. Comparison of predicted damage with actual slope performance over historic time span window of 2000 years allows us to conclude that introduction of 2% kinetic damping should suffice for realistic damage predictions. This conclusion is in agreement with recent results of Tsesarsky, Hatzor and Sitar (2002) who compared displacements of a single block on an inclined plane subjected to dynamic loading obtained by DDA and by shaking table experiments. Using dynamic DDA it is shown that introduction of a simple rock bolting pattern completely stabilizes the slope. RÉSUMÉ : On présente dans cet article une analyse bidimensionnelle complète de la stabilité d’une pente rocheuse très fracturée. La pente rocheuse étudiée est la terrasse supérieure du Palais du roi Hérode à Massada, située sur la rive Ouest du Rift sismiquement actif de la Mer Morte. La pente est constituée de blocs de dolomite raide présentant une stratification sub-horizontale et des joints sub-verticaux. La déformation dynamique de la pente est calculée en utilisant une version entièrement dynamique de l’Analyse de Déformation Discontinue (DDA) où l’accélération dépendant du temps est utilisée comme donnée. Les modes de rupture déterminés analytiquement des blocs clés dans la pente rocheuse fracturée sont clairement prévus par l’approche DDA à la fin du calcul dynamique. On trouve cependant, que pour obtenir des estimations réalistes du déplacement, il faut introduire un facteur de dissipation énergétique sans lequel la formulation DDA serait totalement élastique et sans amortissement. En comparant l’endommagement prévu avec les caractéristiques de la pente sur une période historique de 2000 ans, nous pouvons conclure que l’introduction d’un amortissement cinématique de 2% suffit pour obtenir de prévisions réalistes. Cette conclusion est conforme aux résultats récents de Tsesarsky, Hatzor and Sitar (2002) qui ont comparé les déplacements d’un bloc isolé sur un plan incliné sous chargement dynamique obtenus avec l’analyse DDA et à partir d’essais sur table vibrante. ZUSAMMENFASSUNG: En utilisant une modélisation DDA dynamique on montre que l’introduction d’un système simple de boulonnage stabilise la pente.In dieser Veroeffentlichung wird eine vollstaendig dynamische, zweidimensionale Stabilitaetsanalyse eines hoechst diskontinuierlichen Steinhangs dargestellt. Der untersuchte Hang ist die obere Terrasse des Herodespalastes in Massada, welche in den westlichen Randgebieten des seismisch aktiven Toten Meer Grabens liegt.Die dynamische Deformation des Berghangs wird mit Hilfe einer vollstaendig dynamischen DDA-Version berechnet, in welcher als Input die zeitabhaengige Beschleunigung eingegeben wird. Die analytisch bestimmten Versagensarten kritischer Schluesselbloecke in diesem zerkluefteten Steinhang werden durch Anwendung von DDA am Ende der dynamischen Berechnung klar vorausgesagt. Es zeigt sich jedoch, dass fuer realistische Dislozierungs-Abschaetzungen ein gewisses Mass an Energieverlust in der sonst vollstaendig elastischen, ungedaempften DDA-Fassung einbezogen werden muss. Der Vergleich des vorhergesagten Schadens mit dem aktuellen Verhalten des Berghangs waehrend einer historischen Zeitspanne von 2000 Jahren erlaubt uns zu schliessen, dass ein Zusatz von 2% kinetischer Daempfung fuer eine realistische Vorhersage des Schadens ausreichen sollte. Diese Schlussfolgerung steht im Einvernehmen mit neuen Ergebnissen von Tsesarsky, Hatzor und Sitar (2002), welche die Dislozierung eines einzelnen Blocks auf geneigter Ebene unter dynamischer Belastung – unter Anwendung von DDA und “shaking table”-Versuchen – verglichen. Mit Hilfe der dynamischen DDA wird gezeigt, dass der Steinhang durch Anwendung einer einfachen Steinschraubenstruktur vollkommen stabilisiert werden kann.

Jan 1, 2003