Search Documents

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By G. L. Smith

As the Platinum mining industry expands in the Eastern Limb of the Bushveld Complex it is increasingly evident that a major constraint to development is a lack of appropriate infrastructure. Of critical concern are water resources and spatial development / infrastructure. This paper identifies the context for infrastructure development in the Eastern Limb and two solutions that have evolved in the areas of water supply and spatial development. INTRODUCTION In an economics context, infrastructure is considered to be the structural elements of an economy which allow for the production of goods and services, without themselves being part of the production process. Despite the lack of a specific definition, infrastructure has largely become understood as to comprise road and rail transport systems, public transport systems, airports, public educational facilities, water supply and water resources, wastewater management, solid waste treatment and disposal, electric power generation and transmission, telecommunications and hazardous waste management systems. Critically it is important to understand that infrastructure not only comprises these physical elements but also the operating procedures, management practices and developmental policies that facilitate the effective utilization and development of the infrastructure in response to societal demand.

Jan 1, 2008

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

[Dr. N.A. Barcza (Chairman) Mr. R.J. Linnell (Vice Chairman) Mr. J. Basson Dr. L.A. Cramer Mr. W.A. Gericke Dr. N.C. Machingawuta Mr. C.S. Mahony Dr. L.R. Nelson Mr. D. St J. Slater Mr. B.J. van der Walt INFACON X TECHNICAL PROGRAMME COMMITTEE Dr. L.R. Nelson (Chairman) Mr. W.A. Gericke (Vice Chairman) Mr. W. Barrett Mr. T.R. Curr Dr. O.F.R.A. Damm Prof. R.H. Eric Mr A.M. Hearn Mr. A.R. Jamieson Dr. N.C. Machingawuta Mrs. L. Mthombeni Mr. F.X. Prins Mr. J. van Tonder ]

Jan 1, 2004

The Institute of Lighting Engineers of South Africa The Institute of Lighting Engineers of South Africa (ILESA) was constituted in May 1972 and now has over 70 members. The first Annual General Meeting was held on 15th August, 1973, at the Philips Auditorium, when the first presentation of membership certificates was made. Book Reviews Der Hochofenprozess. Das kinetischdynamische Simulationsmodell des Vereins Deutscher Eisenhiittenleute.Diisseldorf, Verlag Stahleisen M.B.H., 1973. Jones, M. H. and Woodcock, J. T. Ultraviolet spectrophotometry of flotation agents with special reference to the determination of xanthate in flotation liquors. London, Institution of Mining and Metallurgy. 1973. 25 pp. £2,50. Notice VI INTERNATIONAL CONGRESS OF ENGINEERS The above congress is to be held in Barcelona from 6th to 10th October, 1974. NIM reports Report No. 1568 A computer programme for the estimation of parameters in flotation. Report No. 1571 The commissioning of a direct-reading spectrometer for the analysis of silicate rocks by use of the graphite-pellet technique. Report No. 1579 The determination of tin tn geochemical- survey samples. Report No. 1587 A preliminary investigation of the flotation of copper-activated sphalerite without the use of collectors. Report No. 1589 Preliminary investigations into the flotation of tin dioxide, cassiterite, and some related gangue minerals. Professional . engineers Reference (18/19/1) 22nd November, 1973 Dear Sir/Madam, From time to time questions are being asked publicly concerning registration of professional engineers. These questions mainly concern the time it takes to finalise applications, especially those of applicants who do not hold a recognised engineering qualification. Professionele . . Ingenleors Verwysing (18/19/1) 22 November 1973 Geagte heer/dame, Van tyd tot tyd word daar vrae in die openbaar gestel oor die registrasie van Professionele Ingenieurs. Vrae gaan veral oor waarom dit so lank neem om aansoeke af te handel, veral van aansoekers wat nie 'n erkende ingenieurskwalifikasie besit nie.

Jan 3, 1974

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

By M. Yavuz

Two different methods of fuzzy multiple criteria decision making have been proposed to solve the problem of mining method selection in the paper titled ?Mining method selection by multiple criteria decision making tool, by Bitarafan and Ataei. This problem is really important and also difficult to solve because of the need of handling many criteria simultaneously in the process of decision making. Bitarafan and Ataei have selected 15 criteria for the case study in their paper and those criteria have not been clustered/grouped yet. The number of selected criteria is only 15, although there are more criteria that should be handled in a real case, because they have used Saaty?s method in the section ?Fuzzy multiple attribute decision making? in their paper. Saaty?s method considers the pair wise comparison of criteria and uses random indexed which have already been derived and published. Available random indexes, however, have been derived for maximum 15 criteria so far.

Jan 1, 2007

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

The paper discusses the improvements achieved after an external sparger flotation column was installed as a final cleaner at the Northam Platinum Ltd. UG 2 concentrator in South Africa. It further discusses the improvements achieved after the conversion of a conventional flotation column, utilized as cleaner in the Merensky concentrator, to an external sparger flotation column. Finally, the application of the above knowledge in the design and commissioning of an external sparger flotation column as final cleaner in the furnace slag concentrator, is also discussed. 1. FINAL CLEANER AT THE UG 2 CONCENTRATOR The MF2 designed UG 2 concentrator is processing 75 000 tonnes run of mine ore at a head grade of 4.0 g/t 3PGM+Au and a feed Cr2O3 concentration of 28 %. Since commissioning of the plant in 2001, Cr2O3 in final concentrate amounted to approximately 5 % of the total mass. Although final concentrate produced from the UG 2 concentrator is blended with final concentrate obtained from the Merensky concentrator before smelting, blended Cr2O3 values in excess of 1.6% lead to difficulties in the subsequent smelting process. Several options for reducing the amount of Cr2O3 in final concentrate have been evaluated namely:- ? Differing types of depressants at various dosing rates. This test work did not reduce the amount of Cr2O3 reporting to final concentrate by any significant extent. ? Reduction in mass pull to minimize the entrainment of Cr2O3 in the concentrate stream.. This process change had a detrimental effect on PGM recovery. Conclusions were drawn that conventional mechanically agitated flotation cells could not achieve the required selectivity without sacrificing PGM recovery. As a consequence an alternative mechanism needed to be incorporated for the final cleaning of PGM concentrate.

Jan 1, 2007

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

ADVANCES IN EXTRACTION METALLURGY AND REFINING A symposium organised by the Institution of Mining and Metallurgy will be held in London from 4th to 6th October, 1971. Particulars can be obtained from: The Secretary, Institution of Mining and Metallurgy, 44 Portland Place, London WIN 4BR, ENGLAND. ICAMC -71 - HUNGARY The Third International Conference on Automatic Control of Mines and Collieries will be held at Balantsfured, Hungary from 27th to 30th September, 1971. Further particulars can be obtained from: ICAMC - 71, Budapest 3, P.O. Box 115, HUNGARY. AUSTRALIAN INSTITUTE OF MINING AND METALLURGY Illawarra Branch A symposium on "Blast Furnace Injection" is to be held at Wollongong University College from 15th to 17th February, 1972. About 20 papers on various aspects of blast furnace injection will be presented, including two on nonferrous furnaces. Further particulars may be obtained from: N. Standish, Chairman, Symposium Committee, Wollongong University, Australia 2600.

By J. A. Venter, M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential tobe higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and a lack of collector interaction with the mineral is not the reason for low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

By S. Rupprecht

Project evaluations of mineral deposits are necessary for mineral rights, owners and investors alike. A feasibility study provides a definitive technical, environmental and commercial base and is the key element leading to a decision to invest or not to invest. For example, the study may be used to justify further exploration and development expenditure or to provide a basis for a major underwriting to raise the required capital. There are three distinct phases in the development of a project and the type of study will differ depending on the quality of information available or the level of decision to be made. This paper looks at these three phases in the development of a mineral project and the type of study required; namely, a scoping study, prefeasibility, and a full feasibility study. Keywords: scoping studies, feasibility studies, mining projects.

Jan 1, 2004

By B. R. Broekman, D. W. Penman

Discussion by P.J Lloydt Broekman and Penman describe (J.S. Afr. Inst. Min. Metal., vol. 91, Aug. 1991, p. 261) the addition of sodium cyanide and zinc sulphate to the flotation feed at Prieska. They note that for &apos;safety sake, lime was added to the rod mil to raise the pH to 9,5&apos;, and that &apos;personnel working in the vicinity of the rod mil were required to wear gas masks&apos;. Author reply to P.J. Lloyd We thank Dr Lloyd for his interesting contribution. As he correctly points out, the Prieska float had run with cyanide solutions at pH values of 6,4. In fact, it ran safely for extended period with the pH slightly below 6.

Jan 1, 1991

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By X. B. Zhao, J. G. Cai

When stress wave propagates through fractured rock masses, the wave will be slowed and attenuated due to the presence of these fractures. If the amplitude of stress wave is large enough to mobilize nonlinear deformation of these fractures, they will present different effects on one-dimensional P-wave propagation compared with those of linear deformational fractures. The static BB model is adopted to describe the nonlinear deformational behavior. Method of characteristics combined with displacement discontinuity theory is used to build analytical solutions of wave particle velocities and wave stresses. These equations are numerically solved with sufficient accuracy.

Jan 1, 2003

By R. B. August, J. N. Dunlevey

The Quaternary Age aeolian dune sands of the Sibaya Formation on the northern KwaZulu-Natal coast are well known for their heavy mineral content. Although ilmenite, rutile and zircon are the economically important members of the heavy mineral suite, many other nonsilicate minerals such as monazite, xenotime, chromite, magnetite, and spinel that are normally considered to be eitherun common or even rare are also present and these sands provide a unique opportunity to study such complex minerals. Monazite is the general term used for a complex series of rare earth phosphates dominated by lanthanum, cerium and neodymium with monazite-Ce, monazite-La and monazite-Nd recognized as distinct end members of the solid solution series. In addition to the elements indicated by the simplified formulae (LaCeNd) PO4monazite can also accept significant quantities of other elements from the lanthanide and actinide series (Pr, Pm, Sm, Eu, Gd, Tb, Dy,Ho, Er, Tm, Yb, Th, Pa, U, Np). The monazite grains in the Sibaya Formation occur as both composite grains, composed of two or more distinct mineral phases, and homogeneous grains. The net physical properties of the composite grains, and their response to magnetic and electrostatic separation methods are related to size and composition of non-monazite component. However, the homogeneous monazite grains also display significant variation in their physical properties related to their chemical composition.

Jan 1, 2003

By S. M. Rupprecht

A deposit to be mined by underground methods can be accessed by a number of methods: ? Adit ? Decline or ramp ? Inclined shaft ? Vertical shaft. Adits are an economical approach when the orebody is above the general floor elevation i.e. suitable in hilly or mountainous terrain. Incline shafts are limited to relatively shallow deposits, and because they are developed on an incline, development lengths for a given depth are the three to five times longer than for a vertical shaft. Vertical shafts are the preferred method for deposits deeper than 300 m but the development rate is slow and construction costs are very high. Declines or ramps offer early access to shallow deposits, which develops the ore body expediently, but are generally developed at a gradient of approximately 12 per cent. Decline haulages have become an attractive alternative to shaft hoisting, and over recent years the role of decline access has become more widespread throughout South Africa. Traditionally, South Africa has enjoyed the use of shaft systems, largely due to the large knowledge base of mining the Witwatersrand Basin, where vertical and inclined shafts were the norm. South Africa has also had the advantage of cheap electricity, giving shafts a definite economic advantage. However, in recent years the national power utility ESKOM has undergone an expansion programme that has led to tariff increases of nearly 100% over a three-year period. Based on the changes in electricity tariffs and technological improvements to underground haulage trucks, the economic inputs to access development have changed. This paper reviews mine access for shallow deposits as currently applied in South Africa. Based on current economic inputs, the paper investigates at what point a vertical shaft would be more economical than a decline system utilizing typical South African mining equipment.

Jan 1, 2012