Search Documents

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

In 1960, the Secretary of the Interior, acting under the provisions of Public Law 454, 80th Congress, appointed a Lignite Advisory Committee to aid in programming research on coal (lignite) of the north-central area. The chairman of this committee is the Secretary of the Interior or his delegated representative, and in all meetings held during 1960 and 1961, the Director of the Bureau of Mines, Marling J. Ankeny, has presided. The members of this committee were R. W. Rovelstad, President, Baukol-Noonan, Inc., Noonan, N. Dak. W. E. Keller, Vice President, Northwest Division, Truax-Traer Coal Co., Minneapolis, Minn. A. M. Cooley, Professor of Chemical Engineering, University of North Dakota, Grand Forks; N. Dak.

Jan 1, 1963

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By N. H. Snyder

THE Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the com-position as shown by proximate analyses. To these, when required, are added the fusing temperature of ash, Hardgrove grindability index, and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 4 issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) are valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1953

By Parviz F. Rad

The Bureau of Mines used a linear cutting apparatus equipped with a 7-inch disk cutter to cut grooves in marble, limestone, granite, and quartzite under a normal force of 7,000 lb. The size distribution of the muck for various grooves was determined through sieve analysis. A statistical search showed that Weibull distribution describes the size distribution better than other available functions. Results indicate that fineness modulus, chip population, and dimension of the largest chip can be used as indicators of cutting efficiency. The results correlate with those obtained from the boring machines and other lab experiments. Application of the principles established through this work to the operation of boring machines is explained

Jan 1, 1974

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By G. W. Jones

In a previous report'/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933

By R. R. Sayers

"The number of investigations reported during the past year indicates that control of the health hazard due to abnormal air conditions is still a matter of serious consideration in the mining, metallurgical, and allied industries.Australia. - In an investigation into the health and working conditions of employees in the mining industry of Tasmania and Victoria3, it was found that although pulmonary tuberculosis may occur early in life, silicosis is e disease of slow evolution and does not appear frequently under the ace of 40. A period of at least ten years in the industry was found necessary to produce silicosis, and in no case was the disease found in those who had not worked underground. A very high incidence of silicosis was found in all fields among those who had worked underground 20 years and longer. There was some evidence that silicosis complicated by tuberculosis may occur earlier than uncomplicated silicosis.England. - In a paper presented before the Section on Occupational Diseases of the British Medical Association, Dr. E. L. Middleton, the medical inspector of factories, called attention4 to the occurrence of silicosis in various industries throughout the country.punitive on some quite harmless industries. Thus Middleton says: ""Where the amount of dust is small the action of the phagocytes is likely to be effective, but where it is great . . ."" What dosage is indicated by ""small"" and ""great"" in this connexion? If the meaning of ""small"" were known, would it be correct to go on to say, as he does, ""each successive dose of silica produces a summation of effects""? Then, again, would it be fair to say ""a comparatively brief period of exposure may be the only determining factor""? What, in minutes, hours, or days per week, per month,' or year, is intended by ""a comparatively brief period""? ""Intermittency of the process"" is another expression used in summing up the reasons for and against a standardization of air purity by a gravimetric process or enumeration of the particles; the arguments against such a standardization are, by Middleton, considered strong, but they are by no means convincing to us. A standard has been accepted in respect of the amount of lead in milligrams per 10 cubic metres of air; Dr. Ronald Lane showed in another paper read that adherence to this makes the occurrence of poisoning highly improbable. Mavrogordato has placed on record figures of silica dust at different stages of the improvements in the workings of the Rand mines, and such a control is in constant operation in them today.We emphasize these points because apparently the Government has taken the unusual course of legislating first and postponing inquiry to a later date, as in the ""Various Industries (Silicosis) Scheme, 1939."" The insurance companies also have a considerable interest in the matter of compensation for the silicosis risk. Where exposure - as in the refractories industries, the grinding industries, sandstone industry, and pottery industry - is day in and day out, they rightly demand a premium far higher than for any other disease scheduled under the Workmen's Compensation Act - 5 per cent on the wages bill. row every industrial employer, such as the paint and varnish manufacturer, who has a sack of crushed silica in his store .room, from which he extracts once a week enough to make a paste With spirit and add to his other ingredients in order to give them the necessary ""bite,"" becomes involved, and may have to abandon the use of the material or pay 8 per cent on his wages bill for an absolutely negligible risk.. For meting out justice standardization seems urgently called for."

Feb 1, 1930

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982