Search Documents

By J. Durkin

The Bureau of Mines has conducted field studies in coal mines throughout the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above these mines. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10% false-alarm rate, the expected probability o detecting a miner's signal" from a depth of 1000 ft is 54% at 500 ft it is 95%. These depths exceed the actual depths of 90 and 50%, respectively, of United States coal mines. Sensitivity studies have shown that at depth of 1000 ft, the probability of detection will improve approximately 2% for each dB of increase in signal-to-noise (SNR) ratio.

By Herbert Haas

The Bureau of Mines is endeavoring to reduce waste and increase efficiency in the production, refining, and utilization of petroleum . During the last few years the demand for petroleum and its products has increased so much more rapidly than the production that greater efficiency in utilization is now a matter of most serious importance . The Diesel engine, a comparatively new type of internal-combus- ' tion engine, is an important device for insuring more efficient utilization of petroleum and coal-tar products, for it consumes heavy liquid fuels such as can not be utilized in other types. Like the gas or the gasoline engine, it is revolutionary within its province. For some uses this engine is replacing gas and gasoline engines , but its most important duty will be to replace the wasteful consumption of fuel oil in steam engines. Not only will a wider use of the Diesel engine relieve the demand, but it will result in more power being obtained from the same consumption of fuel oils . In spite of these advantages, comparatively few Diesel engines are in use in the United States . In this report the author discusses recent developments in the design and construction of the Diesel engine, the fuels suitable for burning in it, and the uses to which it is particularly adapted .

Jan 1, 1918

By Alastair M. Lumsden

A study was initiated to examine the ways in which a number of foreign countries classify and regulate metal/non-metal mines which experience problems due to naturally-occurring flammable gases. Twenty countries were selected for study, and useful information was obtained from sixteen of these. Nine countries were visited (five of them twice) to hold meetings with representatives of government mine regulatory agencies and mine operators, and to visit mines encountering methane and other gases (carbon dioxide, nitrogen). In the later stages of the study seven gassy metal/non-metal mines in the United States were visited so as to provide a basis for comparison, and hence the evaluation of both the U.S. and foreign gassy mine regulations. In addition to obtaining copies of the mining laws and regulations of a number of foreign countries, nine foreign gassy mines, and the seven in the United States were documented in as much detail as possible. All this information is presented, along with appropriate conclusions and appendices. The study took two years and three months to complete.

Jan 1, 1983

By NORA Mining Sector Council

The National Occupational Research Agenda (NORA) is a partnership program to stimulate innovative research and workplace interventions. In combination with other initiatives, the products of this program are expected to reduce the occurrence of injuries and illnesses at work. Unveiled in 1996, NORA has become a research framework for the National Institute for Occupational Safety and Health (NIOSH) and the United States. Diverse parties collaborate to identify the most critical issues in workplace safety and health and develop research objectives for addressing those issues. NORA entered its third decade in 2016 with an enhanced structure. The 10 sectors formed for the second decade will continue to prioritize occupational safety and health research by major areas of the U.S. economy. In addition, NORA’s seven cross-sectors will continue to focus on the major health and safety issues affecting the U.S. working population. While NIOSH serves as the steward to move this effort forward, it is truly a national effort. NORA is carried out through councils comprised of members with many diverse interests that are developing and implementing research agendas for the occupational safety and health community over the third decade (2016-2026) of NORA. Councils address objectives through information exchange, partnership building, and enhanced dissemination and implementation of evidenced-based solutions. NORA groups industries into 10 sectors using North American Industry Classification System (NAICS) codes. The Mining Sector encompasses NAICS code grouping 21xxxx where “xxxx” represents the different subcodes of the mining “21” classification. Mining encompasses the extraction of solid mineral and mineral-like substances from their place in the Earth’s crust and supplies them to processing industries that produce economically valuable materials. It does not include oil and gas extraction. The Mine Safety and Health Administration, MSHA separates mining into coal, underground and surface, and metal and nonmetal, underground and surface.

Feb 1, 2024

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By M. D. Heresy, H. F. Coward

"Whenever a manometer has been used for recording explosion pressures it has been calibrated under a series of static pressures. Whether the readings taken during the rapidly changing pressures of an explosion (dynamic pressures) truly represent the actual pressures therefore is an open question. The authors had hoped to solve this problem by conducting the calibration with the aid of known pressures, applied at about the ammo rate as in an explosion, for example, by means of a cylinder and piston, the piston being driven in by an eccentric cam at a rate which would be determined accurately by the shape and rate of revolution of the cam. If the rate of compression were great enough, then the pressure in the cylinder (to which the manometer is attached) could be calculated from the laws of adiabatic changes of pressure and volume. It seems highly probably, however, from H. T. Tizard's observations on pressure changes in a cylinder during rapid compression (55) 4/ that there is much heat loss, therefore pressure loss, in the very small interval of time during compression; although Tizard was able to estimate the amount thereof, he did so only by relying on his nanometer, which is exactly the procedure that the authors challenge on the grounds that the manometer was not standardized under the conditions of its use. Hence the authors were driven from this scheme of calibration to another, namely, comparing records of ono and the same explosion taken simultaneously on several instruments of as varied a type as possible. If 2 of a number of instruments agree, perhaps both are accurate; if 3 agree, probably each of the 3 is accurate; if 4 agree, it is almost certain each of the 4 is accurate.There was a second objective in the present work. If the Bureau of Mines and the B.C.D. (British Coal Dust) manometers differ in their records, then from a sufficiently comprehensive series of experiments it may be possible to coordinate the extensive results already obtained at the American and British stations.Thirdly, it was hoped to learn which is the best available instrument for observing the pressures of coal-dust and as explosions and, if possible, to indicate means for improvement in manometry."

May 1, 1935

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By Richard A. Rivell

This document is a users manual intended as a reference for personnel interested in the analysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The interactive procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures available include Gauss-Seidel and Newton-Raphson iterative techniques for the analysis of normal operation or balanced faults as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults.

Jan 1, 1980

By John G. Parker

The rare-earth elements, sometimes known as the lanthanides, comprise the series of 15 chemically similar elements with atomic numbers 57 through 71. Yttrium, with atomic number 39, is often included in the group, because its properties are similar and it more often than not occurs in association with the lanthanides. Thorium is included in this survey due to its close association with the lanthanides, particularly in the mineral monazite. The lanthanides were first recognized as elements around 1750 and were the subject of much study by chemists during the 19th century. The purely chemical methods then available failed to resolve the strange intimate relationships between these elements, and it was not until about 1920 that the full series was explained.

Jan 1, 1971

By F. D. Sutterfield

This study was conducted to provide experimental evidence on the effect of modifications of gasoline front-end composition on the photochemical specific reactivities of automotive emissions. Evaporative and evaporative-plus-exhaust emissions from an automobile operated with four fuels of different volatility and varying levels of C.-C5 olefins were irradiated in a 10040 environmental chamber at three sets of initial hydrocarbon-nitrogen oxides concentrations. Reactivity was measured and expressed in terms of rate-of-NO2 formation and dosages of oxidant, peroxyacetyl nitrate, and formaldehyde. The compositional changes that were necessary in reducing fuel volatility were found to have no significant effect on the reactivity of the emissions. However, replacing C4-C5 olefins with saturated components resulted in sharp decreases in all reactivity manifestations observed for the evaporative emission samples. A lesser influence (of C4-C5 olefin replacement) was found with the composite exhaust-plus-evaporative samples; the effect that was observed could be attributed to the evaporative emission portion of the sample. The data therefore suggest that saturation of front-end fuel olefins had no large effect on exhaust emission reactivity.

Jan 1, 1971

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company's Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

By Arnold O. Tanner

Tables based on 1985 data, which were not available in time for publication of the "1985 Minerals Yearbook," are included in this chapter; corresponding tables for 1986 are not yet available. Raw nonfuel minerals produced in the United States during 1986 had an estimated value of $23.5 billion, an increase of $0.25 billion over the 1985 value. This is the fourth consecutive year that the value has increased, and except for a de- crease in 1982, the value each year has increased since 1971, or 14 out of 15 years. Industrial minerals growth slowed from a 3% increase in value in 1985 to a 1.5% increase in 1986, reflecting the slow growth in the domestic economy. The value of industrial minerals, more than three times larger than the value of metals, easily offset the less than 0.5% decline in the value of metal mine production. Although the decline was small, this decrease makes 1986 the fourth year in the past 6 years in which a drop in the value of metal mining production occurred in the United States. U.S. production continued to lag behind the growing world production. Overall, the estimated raw nonfuel mineral production rose 1% over that of 1985. Domestic mine production of ferrous metals declined as follows, in decreasing order of production: nickel, iron ore, tungsten, and molybdenum. All remaining domestic primary nickel and tungsten mines had closed down by yearend. Nonferrous metals that similarly declined included titanium, rare-earth metals, lead, silver, zinc, and magnesium. For the second consecutive year, aluminum, produced predominantly from imported bauxite, declined in production, while imports reached record-high levels. Somewhat modest gains were made in beryllium and copper. As has been the case for a number of years, gold was a bright spot in the domestic and internation-al metal mining industry. Gold production was spurred on by the increasing usage and development of heapleaching techniques that make lower grade ores, which were previously uneconomical, profitable. Additionally, various mining companies, the U.S. Mint, individual States, and a number of foreign countries began production of gold bullion and commemorative coins. Gold output in the United States increased from 2.43 million troy ounces (revised) in 1985 to about 3.73 million troy ounces in 1986, a dramatic 54% rise.

Jan 1, 1988

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1986. Shipments of processed tripoli increased slightly in quantity and 20% in value. Production of garnet, a common iron- aluminum-silicate mineral, decreased 12% in quantity and value. There was a 4% increase in the quantity and an 11% increase in the value of refined garnet shipped when compared with 1985 shipments, a new record high. Production of crude special silica stone decreased 7% in quantity and slightly in value, and shipments of finished special silica stone products decreased slightly in quantity and increased 229% in value. Production of emery, an impure aluminum oxide, increased 77% in quantity and increased 269% in value of product mined and shipped. [ ]

Jan 1, 1988

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

By W. T. Abel

The difficulties associated with wet-processing fine size coal led the Bureau of Mines to investigate a dry process for removing pyrite from coal pulverized to powerplant fineness. The dry process that was investigated consists of two cleaning steps: First, centrifugal separation is used to remove a fine, pyrite-depleted portion as a product; second, the remaining coarser, pyrite-enriched portion is taken to electrostatic separation in which pyrite is concentrated and rejected. Ball milling and Hardgrove milling were used to pulverize the coal. Three coals from the Pittsburgh seam were treated by the dry-removal process. Over 55 pct of the pyrite, which amounted to 70 pct of the available pyrite, was removed in a reject of 10 to 20 pct from one of the coals. Similar treatment of the other two coals removed about 35 to 50 pct of the pyritic sulfur, which amounted to about 70 pct of the available pyritie, sulfur from these coals. Both centrifugal and electrostatic separations were more efficient when pyrite particles were as large as possible. Separation efficiency was improved by confining the particle size of the feed to a relatively narrow range and by avoiding excessive amounts (more than 10 pct) of dust in the electrostatic range. The removal efficiency was increased with the use of stage grinding.

Jan 1, 1973

By E. H. Burroughs, M. J. Gavin

The references in the following compilation are selected chiefly from the literature of the years 1915-1920 , though a few of the more valuable standard works published before that period have necessarily been included . References to many articles have been omitted purposely , because the material covered by them is duplicated in publications included in the bibliography . It is manifestly impossible for the Bureau of Mines either to recommend or adversely criticize the statements of the various writers , particularly as to cost and profit estimates in articles referring to American shales , but it is hoped that the investigator will use caution in considering such statements , as it is well known that much of the literature on this subject has been published for promotion purposes and is therefore over- enthusiastic . Bearing this fact in mind , the reader should be able to judge for himself the reliability or usefulness of these articles .

Sep 1, 1921