Search Documents

By P. A. Cox

The purpose of the initial research performed under this contract was to determine the margins of safety in explosion-proof (XP) enclosures, which were designed and certified according to the current schedule (Schedule 2G). Results from this work provide baseline data on the current schedule, from which a new schedule can be formulated to give equal or greater levels of safety. Results and discoveries in the initial work led to an expansion of the contract to cover, additionally, weld quality in enclosure fabrication, reliability of enclosures with windows and lenses, and performance tests for enclosure qualification. Finite element calculations and hydrostatic tests revealed wide variations in the margins of safety in the enclosures studied; however, only one enclosure had a safety factor which was less than one. Results from a weld quality survey led to the recommendation of AWS Welding Standard D14.4 for the fabrication of XP enclosures. Based on other work, accelerated aging tests were recommended for qualifying plastics and adhesives that are used in some enclosures, and a Structural Performance Test was developed to test enclosure strength for a minimum static pressure of 150 psig.

Jan 1, 1982

By D. Harrington, G. S. Rice, R. R. Sayers

"The Bureau of Mines in Serial No. 2606,4 issued in May, 1924, gave tentative specifications for rock-dusting to prevent coal-dust explosions in mines. Subsequently, a sectional committee of the American Engineering Standards Committee was appointed to formulate recommendations for standard practice in rock-dusting coal mines. The report of this Committee which follows was approved by the American Engineering Standards Committee, December 30, 1925. Several members of the Bureau of Mines staff served on this Sectional Committee and its recommendations are essentially in harmony with those of the Tentative Specifications in Serial No. 2606.As certain explanatory details contained in that serial are not included in the recommendations formulated by the American Engineering Standards Committee, it should be considered by coal-mine managements in conjunction with the committee's report which follows:Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions 1. Definitions of Terms Used: The term ""Mine"" shall include all underground excavations from which coal is hoisted or transported to the surface, through one or more openings.The term ""Main Haulage"" shall include all underground slopes and planes, all rock tunnels, and all entries excepting those from which rooms or chambers are turned.The term ""Entry"" shall include all underground haulageways, travellingways and airways, excepting working places as defined below:"

Mar 1, 1927

By H. D. Kline

This publication describes methods and techniques of mining and crushing limestone at 3 of 11 small quarries operated by Anderson-Oxandale Rock Co. in northeast Kansas in 1959. It is one of a series of reports by the Bureau of Mines on methods and costs of mining in various mining districts in the United States. The three quarries selected for study -Bosse quarry, Pottawatomie County; Hansen quarry, Morris County; and Huston quarry, Dickinson County (fig. 1) -were in many respects similar to many others that had been developed solely to fill local and usually transitory demands for crushed limestone for use as concrete aggregate, roadstone, and soil conditioning. Factors governing the choice of quarry sites were quality of limestone, shallow overburden, and proximity to points of consumption of the crushed stone.

Jan 1, 1962

By O. M. Schaus

This paper is one of a series, prepared by the Bureau of Mines and deals with the Montreal mine, one of only two active properties in Wisconsin on the Penokee-Gogebic range. The purpose of this paper is to describe the conditions of occurrence of iron ore in a particular property and to present sufficient details of equipment and production methods to convey to the unacquainted operator a correct idea of the mining practice.

Jan 1, 1930

For 11 years, under authorization of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325), and amendments, the Bureau of Mines has carried on an extensive research and development program to establish methods for producing oil from coal and from oil shale. This act was passed by the 78th Congress primarily because of the stress of wartime demands for liquid fuels to supply our armed forces during World War II. The act was progressively extended by the 80th and 81st Congresses, as later peace-time demand for oil and oil products continued to increase.

Jan 1, 1956

By E. P. Barret

Differences in the reducibility of iron oxide materials have been recognized for a long time. Limonites are deoxidized more readily than hematites, and unaltered magnetites are the most difficult to deoxidize. Sinters are found between hematites and magnetites and vary considerably in reducibility, depending on the sintering practice followed and on the degree of fusion of the product. The increased activity in the beneficiation of taconite recently has made available a new blast-furnace raw material, namely, iron oxide pellets made from magnetic taconite concentrate. Many of the data in this paper apply to these pellets, or glomerules, as they were called when this method of agglomerating iron ores was first considered. To clarify the terms applied to iron oxide materials in this paper, the following definitions are given. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron oxide materials. Sinter is the product from a Dwight-Lloyd or Greenawalt sintering machine. Pellets are formed by balling fine, moist oxide in a rotating drum at room temperature, followed by heating in a shaft furnace to a temperature below that of incipient fusion to develop a permanent bond. Nodules are formed by heating the iron oxide material to incipient fusion in a rotary kiln. Briquets are formed in a mold under pressure, with or without the addition of a binder, and burned to develop a permanent bond.

Jan 1, 1949

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing formation is very thick; ever modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has ,been developed systematically; and every effort has been made to utilize the reservoir energy efficiently. Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim of the study was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing for is very thick; every modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has been developed systematically; and every effort has been made to utilize the reservoir energy efficiently Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim-of the stud,, was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil-field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By J. M. Kurtz

Ten Methane Monitoring Systems and Machine Control Circuits were examined and tested per the requirements in CFR Title 30, Parts 18 and 27, the Standard UL 913 and the document "Test Requirements For Instruments or Apparatus to be Considered for M.E.S.A. Intrinsically Safe Certification (Tentative)". The test results indicate that none of the products complied with all parts of all requirements as interpreted by Underwriters Laboratories Inc.

Jan 1, 1980

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

VOLUME III The objective of Volume III of this report is to provide a concise review of six major types of legal constraints, controls, and regulations on surface coal mining in the United States, as of January, 1976. At the same time, an attempt is made to format the details of federal and state exploration, mining, and reclamation regulations such that point-by-point comparisons can be made and updated as revisions occur. Thus, Volume III should provide both an executive overview and a user's manual of legal controls of surface coal mining.

Jan 1, 1976

By M. G. Zabetakis

This publication describes an investigation conducted by the Federal Bureau of Mines regarding the cause of an explosion of a dephlegmator or fractionating column at the Cities Service Oil Company Refinery, Ponca City, Okla., January 22, 1959. The column was that used with the refinery's No.1 Dubbs Coker. The explosion caused the death of an employee of the refinery and resulted in extensive damage to the refinery and to nearby property. The Bureau's study of the explosion began January 26.

Jan 1, 1960

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By Charles Will Wright

This paper is one of a series dealing with mining problems and summarizing the data contained in the Information Circulars on individual mines that have been prepared by the managers or superintendents and published by the Bureau of Mines. The purpose of this paper is to present the problems encountered in the development of an efficient mine organization and to show the means used by certain mining companies in promoting efficiency. There is also a discussion of the advantages and disadvantages of the various systems of paying and handling labor and a description of their application at the individual mines.

Jan 1, 1932

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975