Search Documents

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By B. J. Moore

This publication contains routine analyses and related source data for 419 natural gas samples from 22 States collected during calendar year 1964 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/ Six previous publications have been made to present the results of 6,293 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1964. The first three, Bulletins 486,5/ 576,6/ and 617,7/ contain analyses and related source data on 5,214 gas samples collected from

Jan 1, 1966

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981