Search Documents

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By D. A. Reynolds

[A few studies on the relationship of the fusion temperature of the ash of coke to that of the corresponding coal have been made on commercial high-temperature cokes. R. J. Rose3/ in 1921 compared the' fusion temperatures of the ashes of 10 coals and. the cokes produced from them and concluded tat they were in such close agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coals As the ash of a coal and that of the coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and preparatory to sampling. Pieters6/ found that coke ash was cantaminated in this manner up to 0.4 percent. extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible,7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coil., especially if the fine grinding of the coke was done by rubbing surfaces of iron, as in a disk pulverizer or bucking plate.]

Jan 1, 1940

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

This report has been prepared in response to a request by the Bureau of Land Management (BLM) Fairbanks Alaska District Office that the Bureau of Mines quantitatively assess the potential supply of minerals from undiscovered deposits in the White Mountains National Recreation Area (WMNRA) and the western part of the North Steese National Conservation Area (SNCA) in Alaska. The assessment will be used to assist in future land-use decision-making. Resource Management Plans (RMPs) for the WMNRA and the SNCA were approved by the BLM in 1986. These plans imposed significant restrictions on new mineral development in the two areas. The level of public concern regarding these actions, especially on the part of the mining industry, has spurred BLM to seek additional information about the potential supply of minerals from the two areas with assistance from the Bureau of Mines. The assessment focuses on an area within the WMNRA and the SNCA which has been administratively closed to mineral entry. The study area encompassed approximately 1.24 million acres and included all of the WMNRA and the western portion of the North SNCA (fig. ES-1). Three quantitative estimates of the potential supply of minerals from the study area were developed: 1) For all lands in the study area, assuming that they are open to mineral entry-the baseline analysis; 2) For those lands which have been closed to mineral entry; and 3) For eleven prospective mineral activity areas, assuming that all are open to mineral entry.

Jan 1, 1989

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By M. C. Irani

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Carlton E. Brown

Sand, which is used widely under the wheels of mine locomotives to prevent slipping, is an important source of silica dust breathed by some employees of certain mines, such as those having appreciable grades on haulageways. The sand, as received, contains dust, and other dust is produced by passage of wheels of the train over the sand. Dust is disseminated into the air by such means as handling during unloading, drying, transporting, underground, sprinkling on the rails, passage of trains over Sections where sand is being or has been used, and walking over deposits of sand (or the dust thereof) on the haulageway. The disseminated dust is inhaled not only by persons in the immediate vicinity but also by others to whom the contaminated air travels. The inhalation of this must should be prevented to eliminate any possibility of the material causing silicosis (sometimes referred to as miners' consumption, miners' asthma, miners' phthiris, or miners' lung) and defined by the American Public Health Association4/ as: A disease due to breathing air containing silica (Si02), characterized anatomically by generalized fibrotic changes and the development of miliary nodulation in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for worm, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray finding.

Jan 1, 1944

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967