Search Documents

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By G. L. Oldright

In the first Report of Investigations of the present series?(No. 4562) the usual course of progress ill reducing the minerals of low-grade ores to their valuable metallic components had been noted as advancing along two lines to concentrate a usually diminishing percentage of these minerals to a smaller bulk of richer product, and then to smelt the smaller bulk more cheaply per pound of metal produced. Fundamental properties of lead compounds made it difficult to treat much richer lead products than are treated at present in several steps of conventional lead smelting, unless ?marked modifications were made. No limits to the richness of the feed itself' were set by the ore (Scotch) hearth; on the contrary, the richer the feed, the better the results given by the hearth. The natural field of operation of the hearth, as determined by the ores available, was seen to lie in the Central United States, with their lead concentrates containing negligible quantities of precious metals and. with few ores of such metals available for use as fluxes. It was noted) however, that even in its chosen field, the Scotch hearth, or "ore" hearths developed from them, was not always used; the usual smelting practice was followed, at times, of sintering followed by blast-furnace smelting for even rich ores.

Jan 1, 1949

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

By R. R. Wells

For several years the Klukwan deposit near Haines, Alaska, has attracted interest as a potential source of iron. Limited field and laboratory investigation has indicated that the deposit contains a large amount of Iron that is recoverable as high-grade concentrate. This report summarizes the results of laboratory beneficiation testing of the Klukwan ore, as represented by six samples submitted to the Alaska Experiment Station of the Bureau of Mines, Juneau, Alaska, Iron is present in the ore as a fine-grained magnetite associated with a pyroxenite type basic rock.. Satisfactory magnetic-separation procedures were developed for the production of concentrates assaying more than 60 percent Fe and 2 to 4 percent Ti02. During the investigation many data were obtained and compiled, but for convenience and clarity data of secondary importance have been omitted or condensed; only the more pertinent test results are discussed in detail.

Jan 1, 1953

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year's activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By Fredrick L. Johnson

In deposits of the John Muir Wilderness, tungsten is the principal metallic element. Gold, silver, copper, and molybdenum could be recovered as by-products from most of the tungsten deposits. More than 1 million tons (0.9 million t) of tungsten resources are estimated to be along the fringes of metasedimentary roof pendants. Gold-silver deposits and silver-copper-lead-zinc deposits with small resources are found at several localities. The association of metal deposits with the intrusive-metasedimentary rock contacts and the widespread existence of these contacts, suggests additional resources exist. The area has no known potential for coal, oil, gas, or geothermal energy.

Jan 1, 1981

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962