Search Documents

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By Dr. Calvin J. Konya, Anthony Konya

Beginning on the Niagara Power Project, presplitting became a widely used blasting technique to obtain smooth walls in mining and construction projects reducing scaling, creating more stable pits, allowing the application of slope steepening to reduce waste removal and increase mining depths, and increasing the safety of mine and construction workers. This technique has been minimally studied in comparison to production blasting and currently two separate theories are present on the mechanics behind the presplit. The first is that shockwave collisions between boreholes cause a tension zone to develop causing the split formation. The second is that gas pressures build in the boreholes causing hoop stresses between holes leading to a presplit formation. Practical blasting methods in presplitting such as propellant presplitting and precision presplitting would not be applicable based on the shockwave theory yet are widely used and documented in the industry. Along with this, modern research using a borehole simulation device and advanced pressure gauges have allowed the authors to obtain true borehole pressures in decoupled blastholes. This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

By Anthony Konya, Calvin J. Konya

This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

Feb 1, 2020

By Martti Hagfors, Mervi Hokkanen

The Finnish Defence Forces has destroyed obsolete and spoiled ammunition in open surface mass detonations at Hukkakero fell, in municipality of Kittilä, in Lapland since 1988. The de-struction method was learned from Sweden in 1987. The disposal camp is organized every au-tumn and it lasts four to six weeks. A gross weight of an average charge varies from 150 to 250 tons and the net weight of explosives from 15 to 25 tons. As a booster there have been used 2 to 3 tons of emulsion explosives. The explosives mainly consist of trinitrotoluene (TNT) containing smaller a mounts of amatol and hexotol. The Finnish Defence Forces Tech-nical Research Centre (PVTT) has studied the environmental effects of these mass detona-tions since they began in 1988.

Jan 1, 2011

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

By Al Romphf

Managing blasting-induced air overpressure levels is a key compliance requirement for most blasting operations. Regression analysis, plotting overpressure amplitude vs cube root scaled distance, will often present a level of scatter which should be considered unacceptable. Relying solely on regression-based predictions can lead to overly conservative restrictions that may negatively impact other key performance indicators. Improved methods are needed for accurate overpressure prediction. The Heelan-Blair wavelet has been shown to closely resemble the overpressure waveshape produced when a single charge is fired under typical confinement conditions. The amplitude of a single-hole overpressure wave is influenced by factors such as proximity to the receiver, charge mass, orientation, and confinement both at the collar and face. Additional factors, including timing sequence, barrier effects, wind direction and velocity, must also be considered. The linear superposition method, commonly applied for ground vibration prediction, can be adapted for air overpressure modelling. In blast design software, this approach can consider all relevant parameters and environmental interactions. Given the uniform nature of air compared to rock, linear superposition using realistic elemental wavelets may replace the need to fire a signature hole. Data from 38 single-hole blasts conducted at quarries and mines throughout North America were used to develop and calibrate a linear superposition model. This model reasonably reproduces air overpressure results from full-scale production blasts, offering a practical approach to overpressure compliance and prediction.

Jan 26, 2026

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By Constanza Bujes, Mark Jones, Graham Crook, Yansan Jamyanbaatar, Sedat Esen

Tracking ore characteristics such as grade and hardness from its original position into the material handling and processing stages remains one of the key challenges in open pit mining of hard rock deposits. The most efficient technique for rock fragmentation and separation of ore from waste is blasting, which induces changes in the grade distribution by displacing the in-situ ore into a diggable muck pile. Material movement defines the post-blast grade distribution, which is key to optimising the value of the ore and accounting for ore loss and dilution. Techniques to directly measure the displacement in open pit mining have been implemented routinely and have provided calibration and validation data for blast models to build upon. The JK Value-Based Ore Control blast movement model (JKVBOC) is the latest development of a series of research studies into blast movement and ore control at the Sustainable Minerals Institute of the University of Queensland. The blast model discretises the bench into blocks, defines the initial velocity of each block based on the blast design, confinement and explosive properties, and simulates the displacement using a physics engine. Calibration and validation of the model has been performed in open pit hard rock mines in Australasia in diverse confinement conditions. This paper describes the calibration and validation of the blast movement model against direct measurements of blast movement and final muck pile shape for a case study where the displacement of multiple shots was modelled for an open pit mine, with an analysis of the implications for ore loss and dilution. A key finding in this study is the need for further integration of this technology into the existing systems for ore control, and the potential for applications in tracking ore characteristics other than grade into process control.

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation.

Feb 1, 2020

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By Jianping Li, Ernesto Villaescusa, Kelly Fleetwood

During blasting, stress waves propagate through a rock mass, inducing stress and strain changes. This applied deformation affects intact rock, existing discontinuities, mine excavations, and engineered structures in the proximity of the blast. Traditionally in blasting, stress waves are quantified in terms of peak particle velocity (PPV) or peak particle acceleration (PPA), based on the method of measurement and the specified allowable tolerances. During analysis, the peak particle motion is coupled with an explosive source through various scaling laws to develop rock-specific attenuation relationships. Some studies have expanded this practice to the development of damage threshold values based on measured or predicted peak particle velocities. PPV-related thresholds are generally based on empirical models, where observation of overbreak, cracking, or fall-off are used to quantify damage. This method is often paired with the application of elastic plane wave equations to calculate the blast induced strain or the PPV threshold for tensile rock failure. Other factors that must be viewed critically in such models are the methods used to collect and analyse blast vibration data and the application of inappropriate vibration attenuation relationships.

Jan 1, 2009

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By Walt Meglasson

The Kaiser Aluminum Company Smelter, one of several in the Pacific Northwest, was built in 1942 and operated by the Olin Company during World War II and then purchased by Kaiser Aluminum after the war. At its height, the facility employed over 350 workers and was capable of producing 73,000 tons of aluminum per year. It was closed in 2000 through a combination of rising electrical and labor costs, and the inability to compete with more up-to-date foreign facilities.

Jan 1, 2008

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By Bob de Raadt

After a review of the general principles for blasting stacks, the stagnations of two stack demolitions are investigated. The author concludes and demonstrates that MS-delay blasting can be risky under certain circumstances. How this initiation device can still be applied safely to the demolition of stacks is shown in an account of a blasting operation, in which two 106-m (350 ft) -high concrete stacks were involved. The recent discovery of a possible hazard of MS initiation in this field of blasting is an essential contribution to increased safety in blasting tall structures.

Jan 1, 1982