Search Documents

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Perry Sisk

In order to protect nearby structures during a blasting project, a peak particle velocity limit is often stipulated by a government agency or the owner of a particular structure. At the start of a blasting project, a preliminary estimate for the minimum scaled distance is often determined using a vibration prediction equation before any site-specific data have been obtained. Reasonably conservative assumptions are typically made for the unknown input variables in the vibration prediction equation until site-specific blasting data have been obtained and evaluated. Although this approach is prudent, it provides no assurance that the peak particle velocity values generated during the initial phase of the project will be below the specified limit.

Jan 1, 2013

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Anderson Meireles, Vladimir Carrasco, Carlos Feliciano

Adopting new technology in drill and blast requires a structured implementation process, as it represents a significant change in a traditionally conservative industry. It involves addressing initially unknown implications. As the problem is not yet acutely felt, developing a market strategy must be approached from the customer’s perspective, considering how the product can optimize their activities or enhance flexibility. To achieve this, it is essential to have a comprehensive understanding of the context of the customers identified in the deployment process pipeline. This paper discusses aspects of introducing wireless initiation technology - the initiation of primers through a magnetic field without physical connections - in Brazil. Additionally, it presents a case study of the application of a structured process of sales with purpose in an underground mine. By identifying key opportunities that were highly profitable for the client, the necessary awareness was created, leading them to recognize the technology as an enabler for exploring their mineral deposits in a new way which allowed a successful change management process. Based on the applicable technique, a preloading project was developed to maintain inaccessible areas with high-grade precharged with the area loaded with wireless primers acting as a temporary pillar and controlling dilution throughout the orebody. Once the excavation of the stope was completed, the pillar was successfully blasted and the material - once considered lost in the original plan as a rib pillar - was recovered after serving its structural function. Through this method, the metallic recovery of the stope increased without dilution losses. Demonstrating economic viability and stablishing the previously unknown technology as a strategic tool for optimizing stope recovery.

Jan 21, 2025

By Tapan Goswami, Lloyd Hain, Geoff Brent

For many years Ramp 24 at Ensham mine in Queensland, Australia has suffered substantial coal loss and damage due to the fragile nature of the coal and problematic geological conditions, which have proved very challenging. In the past various blasting techniques were applied in attempts to improve coal recovery. One approach was to use a shallow throw (cast) blast followed by a separate post-strip blast underneath. Another method was the introduction of the practice known as “baby decking” with the addition of a large buffer of material in front of the coal. However, despite increasing mining costs, none of these techniques adequately reduced coal edge loss and damage.

Jan 1, 2008

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By L. Wilson, M. Kotzel, T. Pienaar

An empirical equation is presented for the maximum airblast from unconfined charges. This has been tested at a number of sites and with charges ranging from 0.1kg to 311kg. The equation is developed to predict community response to potential explosive test range sites and the testing has added to our knowledge of the effectiveness of mitigating measures. The first site had 10m to 15m high walls that were intended to ameliorate the airblast. These walls functioned to a limited extent and reduced the airblast levels by 2dB to 5dB. The airblast was affected somewhat by topography. Noise levels at the nearest residences exceeded 130dB for charges larger than 1kg, whereas the vibration levels were very small. Formal complaints were received where the airblast level exceeded 128dB as per conventional expectations. Pedestrians and pets in the suburbs were startled by the blasts, emphasizing that the community response is much more sensitive to noise and airblast than vibration levels. The maximum airblast levels were too high for this site to be used on a regular basis. At another site, the airblast levels were significantly increased downwind by up to 10dB due to a moderate wind. A third site, at a quarry, produced unconfined airblast levels beneath the derived limits, but are much higher than the normal quarry blasting. By involving community forums there were no complaints, possibly due to desensitization by the normal blasting activities. The study has highlighted new areas for research in understanding the effect of noise, air blast and vibration on the low cost and informal housing typical in South Africa

Jan 1, 2011

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By R. Jacob

Mining has been around for a long time, and new deposits are being discovered continually but are becoming more complex for processing and typically sulfide in nature. Most of the large easy deposits with simplified and cheaper to process oxide material have been mined or the deposits are locked up with legal or social issues and may never be mined. It is common to see the mines today being evaluated to mine have little in oxides and have a sulfide component to the deposit. This creates a problem with explosives being selected for the mine because ANFO could cause a reactive ground issue. When evaluating the cost component of mining for future mines, ANFO is the go-to selected bulk explosive because of the cost and effectiveness. More work needs to be done by projects evaluating costs by properly testing the ground and water conditions to match the correct bulk explosive for the ground conditions of the mine. This will prevent a possible safety hazard and the best result for the mine.

Feb 6, 2023

By Piotr Mertuszka

Many years of research on more effective and safer explosives have led to the development of emulsion explosives. They are the second most commonly used group of explosives worldwide, primarily because they are good alternatives to ANFO or dynamites. Their key advantage in underground applications is the lower content of toxic fumes in the detonation products. Emulsions are also characterized by high detonation velocity, high water resistance, low critical diameter, and mechanical loading capacity. Several factors affect the behavior of emulsion explosives. These factors are related to both manufacturing and applied mining methods. The most important factors include the charge diameter, type of sensitizer, density, hydrostatic pressure, ambient and charge temperatures, as well as the time elapsed between the charging of the explosive into the blast hole and its detonation. The selection of the type of explosive is based on the analysis of a number of parameters, including the density, critical diameter, volume of the post-blast fumes, detonation pressure, velocity of detonation, and sensitivity to external energy sources. In most cases, the conditions under which explosives are used differ significantly from those defined in standards. Such conditions cover, among others, the temperature of the rock mass and surroundings, humidity, rock strength parameters and the diameter of the blast holes. Consequently, the parameters of the explosives provided by the manufacturers may not correlate with those specified in-situ. Thus, within the framework of this study, the effects of the selected technological parameters on the detonation velocity of bulk emulsion explosives are presented. The analysis focused primarily on the factors directly influenced by the mine blasting services. The detonation velocity measured using the continuous wire resistance technique was used as the evaluation criterion. For this purpose, several underground in-situ tests were conducted, including the impact of the blast hole diameter, density, initiation method, sleeping time, and temperature on the detonation velocity. The results of in-situ tests have shown that the detonation velocity of bulk emulsion explosives depends strongly on the above factors, which may directly affect the effectiveness of blasting operations.

Jan 26, 2026

By Tristan Worsey

This work was performed during the summer of 2008 during the junior year of a BS in Mining Engineering. It was observed that the mine was having a problem with back break during the blasting of development drifts. The unwanted back break was causing the mine extra costs in ventilation, ore dilution, ground support, back fill, explosives and man-hours. The blasting practices were observed for four weeks and the problems and their solutions were defined. In this paper the reasons and causes of the problem are explained with the proposed solutions to eliminate back break.

Jan 1, 2010

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010

Hello, everyone. Way back in 1965, Devine and others at the US Bureau of Mines showed that a presplit fracture plane did not affect vibration levels transmitted across the plane (RI 6695).

Jan 1, 2010