Search Documents

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By Roland Alford

The ballistic pendulum is a well-established piece of test equipment originally developed for estimating the velocity of bullets and projectiles. When trying to understand the effects of different tamping methods on explosive performance, the ballistic pendulum is an excellent tool allowing calculation of explosive charge impulse. Most ballistic pendula for this application are limited to narrow impulse ranges as the pendulum mass determines the angle of swing; and a mass capable of being moved by a small charge would be far too small for a larger charge. This paper describes a modular design (the Alford Modular Ballistic Pendulum) which overcomes this problem.

Feb 6, 2023

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Steve Linehan, John Toedter, Kelly Williams, Mark Herman, Laura Connor, Catherine E. Johnson

Minimum safe distance (MSD) calculations are used widely in military applications to determine safe standoff distances for breaching personnel. Accurate safe distances and an understanding of blast wave propagation are critical to preventing traumatic brain injury. These calculations are often based on spherical charges in open air. However, applications including explosive breaching use planar charges rather than spherical. Previous studies analyzed the shock propagation of a square planar charge of sheet explosive and concluded the anisotropic pattern conflicted with the Kingery Bulmash (KB) and MSD spherical models. It has been determined that these predictions do not adequately predict the realistic pressures in all directions and the trend has shown to be consistent across multiple charge geometries. In this series of experiments, pressures were collected from reference spheres and rectangular geometries of detonating cord and sheet explosive commonly used in breaching and improvised demolition for this comparison. This common configuration showed pressure differences at varying angles to the charge with the highest pressures measured at the 90° position perpendicular to the “door” to be breached. Lower pressures were found at the 0° and 15° positions where the breachers would normally be standing. The reflected shock from a surface such as a door was incorporated in a semi-confined situation and added to the shock observed by the breachers. Urban environments include many surrounding structures for these reflections to occur and further testing is necessary in such an environment to determine the full-scale impact. These findings may be useful to develop improved MSD calculations for breaching applications based on charge geometry, orientation to the blast, and nearby structures.

Feb 6, 2023

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By Elliott Giles

"Measuring a blast’s performance based on the bucket fill time or “diggability” has always been achallenge due to the subjectivity generally involved. The diggability of a blast is often based onopinions and speculation without the data to properly support the claim. This paper focuses howthe blast design can impact diggability and how it can be properly measured."

Jan 1, 2016

By George W. MacDonald

ALFRED NOBEL was born at Stockholm on October 21st. 1833, and died on December 10th, 1896. Although Sobrero’s discovery of nitroglycerin dated back to 1847, this explosive was manufactured on a commercial scale for the first time in 1862, by Nobel at a factory which he erected at Heleneborg, near Stockholm. These works were entirely wrecked by an explosion in 1864. In 1865, he erected works, which are still in existence, at Winterviken, near Stockholm. In 1864 Nobel introduced modifications in the manufacture of nitroglycerin which were the subject of a patent (see footnote No. 1), and at the same time, claimed a process for the detonation of nitroglycerin. Nobel states that, up to that time, the method used for the manufacture of nitroglycerin consisted in pouring glycerin, drop by drop, into a mixture of sulphuric acid and nitric acid contained in a refrigerating mixture. In order that the nitroglycerin should not be decomposed, the temperature was not allowed to rise above 0° C.

Jan 1, 2012

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017