Search Documents

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By Barend Botha, Trevor Davids

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in the Republic of South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a blasthole. A number of inert materials were tested including ash, drill cuttings, river sand and crushed stone. It was found that the ash, drill cuttings and river sand did not effectively attenuate the shock wave and that the risks of sympathetic detonation or partial disruption of one or the other explosives deck in a blasthole was high. This became much worse when the inert material was saturated with water. Crushed rock was the most effective in attenuating the shock wave, but this material was very expensive to use because it had to be imported onto the mine.

Jan 1, 2000

By T. Bernard, P. Dozolme

Electronic initiation devices appeared on the market more than 15 years ago and have definitely changed the rules of blasting. It becomes clear that this technology represents a powerful alternative to the traditional accessories. Electronic Delay Detonators (EDD) have attained solutions that were difficult and even impossible to achieve with the previous technology, thanks to the accuracy, usually inferior to one millisecond, and flexibility of the programmability range offering thousands of timing possibilities. Technological progress is long awaited to represent a step ahead compared with the last generation of products. In the case of electronic initiation, some limits nevertheless rapidly appeared, leading to the paradox of loosing operative and safety benefits, compared with the traditional technology it was supposed to outclass.

Jan 1, 2006

By William C. Geitz

"Lightning has always posed a serious threat to blasting operations, especially wkhin the mining and construction industries and operations involving the manufacture, transport, storage and handling of explosives. In recent years, technological advancements in communications systems and microprocessors have significantiy improved the accuracy and efflliency of lightning detection and warning instrumentation. These advancements have increased the availabilii of highly reliable,accurate and affordable systems for use within the explosives arena."

Jan 1, 1991

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By Roland Oliver

Detonators or blasting caps are made in several different grades of strength, because some powders require not only a greater, but a different initial detonation than others to convey their maximum energy through a whole charge, and the detonating qualities of each powder vary with changes in its physical condition––whether it be warm or cold, rigid, plastic, homogenous or otherwise.

Jan 1, 2007

By Robert Morgan

With improved methods for designing and detonating shots the potential for flyrock can be significantly decreased, but there are few absolutes in blasting; therefore blasters must learn from the mistakes of others. Blasters must conscientiously employ control measures to minimize the risk of flyrock. The worst case incidents which tend to be widely reported by the media, should serve as a reminder to us all that minimizing the risk of flyrock must be incorporated into the design of the drill pattern and blast design.

Jan 1, 2001

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By Nick Lewis

Farce Mining of Texas is a surface coal mine located in Laredo, Texas. Farce mines and sells approximately 600,000 tons /year of bituminous coal. A map showing the location of Laredo is provided in Figure 1. As shown, Laredo is located on the border between the United States and Mexico. The mine property runs to the Rio Grande River, the border between the two countries. Farce pumps water from the Rio Grande for use in their coal preparation plant. Laredo’s climate is quite dry with annual rainfall averaging about 12” per year. Also, due to the southern location, Laredo is quite hot. It is common for the temperature to reach 100” F in March and maintain these temperatures through September.

Jan 1, 1994

The underwater test method for the determination of energy content of explosives is a very useful method. It’s also the only one which can separate shock and gas heave energies from each other. The total energy can be determined as a sum of these partial energies. Because of this special feature, the test method can be used to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The goal of this study was to find out the effects of aluminium and sodium perchlorate increments to the shock, gas heave and total energy values of an emulsion explosive and detect the particle size effects of two different aluminium powders to the total and partial energies as well. Both partial energies as well as the total energy were observed to increase linearly as a function of aluminium (A-80) concentration. The fine aluminium powder (A-100) (6%) also seemed to increase the shock energy of the explosive slightly whereas the gas heave energy was observed to remain unchanged to compared to the normally aluminazed (A-80) (6%) emulsion explosive. Therefore the fine aluminium powder also increased the total energy, but only very silightly. The fine aluminium powder can probably take apart to the chemical reactions more easily during the detonation. (3%) of sodium perchlorate (NaClO4) mixed with (6%) of (A-80) aluminium powdered emulsion explosive was observed to effect to the gas heave energy content of the explosive, but only very slightly. The shock energy was observed to remain unchanged.

Jan 1, 2005

By D T. Froedge

At the 1990 Symposium of the Society of Explosives Engineering, D.T. Froedge, President of GeoSonics Inc., presented a paper entitled "Differential Topographic Vibration Isomapping", which detailed the capabilities of GeoSonics' new Iso-Seismic Service. In this paper Mr. Froedge described how one hundred or &ore free-standing miniature seismographs called Micro-Seis Units, randomly positioned around a blast, could accurately reveal the effects of sub-strata geology on surface ground vibrations. The paper went on to note the "regression analysis of scaled distance versus recorded particle velocity" as being an inadequate predictor of peak particle velocity. This is due to the fact that the calculated "regression analysis" formula for any site is predicted on the wars; case assumption because of a homogeneous and symmetrical sub-strata geology, a condition that rarely, if ever, exists.

Jan 1, 1992

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By Charles Pretorius

Electronic Delay Detonators (EDDs) with remote wireless programming and initiation capabilities have been successfully used for almost two years now. This system has been used in blasts mainly in South Africa, but also in South America and other countries in Africa. Initially the industry was slow to accept the idea of remote programming and blasting. The advantages were not fully understood and there were some safety concerns. With close to 200 successful blasts as a reference, a much better understanding exists. The advantage of such a system becomes even more significant when the programming of the detonators is digitally integrated with the blast design software as used by the Blast Engineer. It is now possible to import a survey file into the blast design software, to do the blast design using actual hole positions and to then export the designed firing times directly to the detonators down the hole via remote wireless communication. Mines that have been exposed to this technology favour it to the extent that wireless centralised programming is becoming the norm against which other electronic delay detonator technologies are measured.

Jan 1, 2005

By Dennis L. Paisley, Thomas P. Turner

Laser slapper detonators are the next generation detonator under development at the Detonations Systems Group at Los Alamos National Laboratory and function very similarly to an electrical slapper. A fiber optic transmits a laser pulse to ablate a thin metal film. This film, or flyer as it is commonly called, is launched through a short barrel to km/s speeds. The flyer shock loads or slaps a high density pressing of secondary explosive, setting off a detonation therein. Laser slapper detonators afford a number of safety advantages over other conventional detonators. Most important they require very high peak laser powers to operate, orders of magnitude larger than possible sources of natural or man-made accidental stimulus. Because light is transported over fiber optics, laser slappers avoid many of the electrical hazards associated with detonators. Use of insensitive, secondary explosives makes these detonators safer to handle, manufacture, transport, and deploy.

Jan 1, 1994

By Michael S. Wieland

Charge malfunction problems result from rather universal damage mechanisms and are widespread throughout surface and underground delay blasting. Recent refinements in instrumentation technology reveal a range of charge performance difficulties, not just outright misfires. This report focuses on the U.S. Bureau of Mines research regarding desensitization and malfunction of delay detonators and cap-sensitive explosives, utilized in underground coal mining. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum. The shock waves from charge explosions propagate outward in all directions through the coal, impacting neighboring charges with later delays. The impact phenomena have debilitating effects, causing degrees of reduced charge performance ranging from misfires or weak detonations to out-ofsequence detonations. Impaired charges react poorly. fracture less coal, and produce fumes with higher toxicity. Coal-mine, underwater, and simulator tests were conducted to m3re thoroughly understand the shock-wave and rift-compression damage mechanisms. Recently the U.S. Bureau of Mines partially resolved the malfunction problem by demonstrating the feasibility of formulating a rugged explosive, which could pass the requisite tests for certifying an underground coal-mine explosive. The charge formulation was not certified only because it lost initiation sensitivity too quickly from natural aging and had to be rebatched to finish the testing.

Jan 1, 1994

By Wang Hong Qu

This paper observes the shape of throw explosion crater its ejecta locus of internal medium and the process of distance along with slope's angle developing. It was discovered that initial velocity is inversely proportional to slope's angle. The velocity of surface distribution at the lower half crater of explosion is larger than at upper one. It carries the relevant calculated formula and physical process of explosion crater forming under the inclined boundary conditions, and some important law. It proved that the gravity influence is very distinct for the blast action in the little resistance line.

Jan 1, 1991

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By Peter Reinders, Dirk Hummel

This paper describes a newly developed Surface Remote Blasting System (SURBS) for electronic detonators, which is currently being introduced into surface blasting applications. The rationale for developing the SURBS was to meet key needs of mine operations, such as minimizing the shutdown time and the capability to conveniently initiate blasts in difficult terrain from a safe distance. Increased distance from the blast site, combined with a good overview of the site enables maximum safety during blasting. The system also removes the inconvenience of running long firing cables. The SURBS consists of the field-proven detonator and equipment technology of an existing electronic detonator system, a Surface Remote Blasting Box and a Surface Remote Blaster. The Surface Remote Blaster is the Master unit and controls the Remote Blasting Box via encrypted radio communication using a sophisticated safety technology, which guarantees that the highest safety standards are maintained.

Jan 1, 2005