Search Documents

By Justus Deen, Paul Sterk

Overbreak into the wall rock of a development drift leads to the inevitable need to rehabilitate a drift. Moreover, overbreak in a production heading can lead to external dilution and lower ore grades. Both of these factors are critical to bottom line costs of underground operations today. The geology of the Homestake orebody makes this an even more complex problem. For over fifteen years the Homestake Mine has attempted to implement perimeter blasting techniques that are both safe and cost effective. Many practical perimeter methods and products have been tested including air decking; low density emulsions; various types of stick powder; various decoupling media including rope, low density ANFO, polystyrene ANFO, salt based ANFO, and various grain detonating cords up to 200 grain.

Jan 1, 1997

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Richard A. Dick

On August 3, 1977 the 95th Congress passed Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. This Act created the Office of Surface Mining Reclamation and Enforcement (OSM), which was given the responsibility of formulating regulations to implement the Act. This paper explains the rationale behind the specific provisions of the final blasting regulations, which were published in volume 44, No. 50 of the Federal Register, dated March 13, 1979. The major items covered by the regulations include preblasting surveys, blasting schedules, protection of the public, ground vibration limits, the scaled distance equation, airblast limits, blasting procedures, and record keeping. The regulations are designed to protect the safety and well-being of the public and to protect buildings and structures such as wells, pipelines, and storage facilities from damage.

Jan 1, 1979

By B Mohanty

The current basis for rating of commercial explosives is examined, with particular emphasis on calculated bulk and weight strengths, detonation velocity and underwater energy measurement. The calculated strengths still form the basis for selecting explosives for most blasting applications, with the measured detonation parameters serving only as a measure of the quality of the explosive. The major drawbacks with this approach are discussed, in view of the non-ideal nature of commercial explosives and the field conditions prevalent during the blasting operation. A unified approach to rating explosives on the basis of blasting performance rather than calculated energy alone is presented for various types of explosives. This incorporates the relevant field parameters as well as the effect of non-ideal reactions, both of which affect explosive energy release and its transfer to target rock.

Jan 1, 1988

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By David Leidel

A major characteristic that distinguishes modern society from its predecessors is the understanding that events are not driven by the whims of the gods, pre-ordained fate or nature, but are controlled to a greater or lesser extent by the actions, (or inactions), of people. The study of risk assessment is the basis for determining risk or the likelihood of an event occurring combined with the consequences of that event if it does occur. This study is indubitably linked to the mathematics of probability and statistics which permits the quantification of risk. As the Industrial Revolution significantly increased the exposure of persons to new types of energy sources, materials, equipment, and means of more rapid transportation of goods and people, quantitative risk assessment became a vital tool in protecting workers and the general public exposed to these new technologies.

Jan 1, 2007

By Carlos Agreda

"It is widely accepted that the rock blasting results are a function of several stochastic variables given by: -The natural geological structure of the rock mass (joint spacings, discontinuities length orientation and characteristics, physical-mechanical properties, such as: ultimate strengths and elastic properties, etc.).-The detonation and explosion parameters of the explosive mixture (V.O.D., P2, T2, Q3, etc.).-The drilling and blasting pattern dimensions.-In this paper the most important stochastic variables regarding with the rock mass and the blast design dimensions before mentioned are identified, described and discussed.A non linear programming method to calculate the optimum burden Bo) is proposed and discussed.The great impact of the stochastic variable called burden (B) on the rock blasting results is emphasized. A comparison between burden theoretical calculations and some field blast results is also shown."

Jan 1, 1996

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Hu Wenjun

This paper changes the section of copper of copper to aluminum adapter bar into aluminum plate covered one face or double face with copper coat, and changes the conductor material of knife switch, fuse box, plug and socket into steel plate covered one face or double face with copper plate, and manufactures the composite (two layers or three layers) metal plates by means of explosion welding with the plates installed horizontally. Introduced in this paper are the blasting designing technique, manufacturing process and the electrical performances of the explosion bonded products. Besides, this paper presents the designing and manufacturing technique of cumulative charges and their time detonating units for cutting off the retired nuclear submarine pipes. Experiments on cutting off the stainless steel pipes by cumulative flow and on the time detonation are made. Keywords: explosive welding, electric, explosion bonded products, retired nuclear installation; pipe; blasting cutting; cumulative charge; time detonation

Jan 1, 2000

By Travis Watts, Chris Prater, G. T. Lineberry

Moving overburden at minimal cost is becoming increasingly important to coal mining companies throughout the U.S. The coal market is currently doing well, with an average spot coal price for Central Appalachia product (12,500 Btu, 1.2 SO2) standing at $62.00 for the week ending November 11, 2005, so it is at this time that companies stand to achieve healthy rates of return on their investments. Cast blasting is one method of blasting used effectively by some surface mining operations. This method allows most of the overburden to be removed and placed (cast) directly in the spoil pile by the use of explosive energy. With the proper design of a cast blast, a high percentage of overburden material can be directed into piles without the use of earthmoving equipment, hence increasing production and lowering the cost associated with overburden removal.

Jan 1, 2006

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

By Sam Taoum, Omar Riahi

Few tools allow for accurately tracking ore dilution after blasting. Existing methods often rely on data analysis or linear interpolation of velocity, which can be imprecise and less effective in varied geological settings. A promising alternative is the use of numerical simulations, which involve complex mathematical calculations incorporating real physical data about explosives and geological characteristics. These simulations can model blast-induced fragmentation and subsequent ore dilution with greater accuracy, providing detailed insights into blast dynamics by considering factors such as explosive type, blast pattern, and rock properties. Numerical simulations integrate data from sources like seismic sensors, blast monitoring equipment, and geological surveys, offering a holistic view that single-method approaches cannot match. By simulating different scenarios, mines can predict the outcomes of various blasting strategies, optimize blast designs to minimize ore dilution, and maximize recovery. Advanced numerical simulations enhance the prediction of fragmentation distribution and size post-blast, crucial for effective dilution control and maximizing ore recovery rates.

Jan 21, 2025