Search Documents

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999

By GF Brent, Armstrong L. W

It is recognised that presplitting is a special case in blasting which requires the reduction of conventional explosive pressures in order to avoid excessive rock damage. Two routes to achieving this are the use of reduced density explosives or the practice of decoupling the explosive from the blasthole walls. Applications of two such systems in large diameter, deep blastholes are described. Both systems were tested in presplits alongside sections charged with decks of conventional explosives.

Jan 1, 1998

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

By Paul Muehl, Roger Lawrence

The massive sculpture taking place on Crazy Horse Mountain in the Black Hills of South Dakota, may Be the most unique application of precision blasting techniques in the world today, It is certainly the largest sculpture in history. And it is being carved not by the usual artist implements, but by engineering of explosives. This paper presents a review of the blastingasting techniques and challenges of blast earring the largest sculpture in the world,

Jan 1, 1991

By Gordon F. Revey

Hanging Lake Joint Venture recently excavated two conventional 42 foot diameter highway tunnels in the difficult ground conditions of Glenwood Canyon, Colorado. This paper outlines the type and success of the various Controlled Blasting Techniques that were used to minimize overbreak in the portal and tunnel excavations. The different Smoothwall and Cushion Charge loads used in the different ground types are described in detail. Delay Timing and Drilling Pattern variations are also discussed.

Jan 1, 1991

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Kunihisa Katsuyama, Yuji Ogata, Takuya Taguchi, Toshinori Arikiri, Yuji Wada, Kiyoshi Hashizume

The impact sensitivity of hot emulsion matrices was examined to investigate the safety assessment in the emulsifying equipment which forms the emulsion matrix in a water-in-oil type emulsion explosive. The sensitivity could not be evaluated by the small fallhammer test device commonly used in Japan. Therefore, a large fallhammer test device was used. It was confirmed that an explosion, a decomposition, or a no-reaction took place according to the degree of the impact. When a decomposition took place in the hot emulsion matrix, the behavior of it was investigated further by a DDT test. It was found that a decomposition, or a no-reaction occurred according to the degree of confinement.

Jan 1, 1997

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By Paul E. Thompson

Current magazine regulations are designed to avoid injury or property damage caused by accidental detonation as well as to store explosives securely. The primary emphasis appears to be the avoidance of unintended detonation or in the event such detonation occurs, the avoidance of damage to surrounding property. Adherence to these regulations largely serves the purpose intended but has caused difficulty in magazine sitting in built up areas. To the extent that magazine siting is too heavily restricted, other more significant dangers such as storage of explosives in more dangerous and less secure places may be encouraged. In summary, the regulations have served rural magazine locations well but may need further study for urban settings.

Jan 1, 1990

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Chad Ducey

The proper utilization of energy in an explosive column is of paramount importance to the success of any blast. Historically, Powder Factor (the weight of explosive per mass or volume of material to be blasted or its inverse), has dictated the blast design. The concept of Energy Factor is a more effective method to design a blast. In order to utilize explosives efficiently, the energy contained in any given product must be quantified. The Powder Factor method, although historically successful, assumes that a pound of cast pentolite affects the material to be blasted the same as a pound of ammonium nitrate / me1 oil (ANFO.) Years of experience and scientific testing have led the blaster in the field to believe otherwise. The next logical technological step is Energy Factor. The Energy Factor method that will be discussed in this paper takes into consideration not only the weight of the explosive, but also the weight strength (Cal/g) and the density (g/cc) to yield a constant relative Energy Factor. The result of such a method is a factor that can be used in the field exactly the same as Powder Factor, but that reflects the relative energy of any given product in terms that will reflect the relative cost benefit of that explosive selection. The Energy Factors associated with different available explosives make it possible to compare the difference in the amount of energy per loaded pound in each unit length of borehole. This paper will examine the concept of Energy Factor in an in depth manner and also compare this quantification method to that of Powder Factor. It will also demonstrate the value of using Energy Factor and how it can improve the efficiency of a blast design. The misconceptions that come along with using Powder Factor will be examined and comparisons will be made between boreholes loaded using Powder Factor and those that are loaded using Energy Factor. This paper will clearly define the differences between these blast design methods and allow the reader to realize the production, quality, and economic advantages of using the Energy Factor method.

Jan 1, 2000

By Jennifer P. Harrell, D. Joseph Hagerty

In many areas of the eastern United States, especially in the Midwest, past mining activities have left large and extensive underground openings. Now, renewed mining is occurring in such areas in surface pits. Also, construction blasting often occurs in rock over such old openings. Within the last fifteen years, some attention has been given to the interaction between surface blasting and underground cavities; concern has been expressed about the possible changes in vibrations transmitted through areas underlain by old mine workings (Siskind, Stachura and Nutting 1987). Previous studies also had indicated that underground openings could influence transmission of surface mine blast vibrations (see, for example, Woodward-Clyde Consultants 1977). The principal concern is that underground openings under surface blasting may intensify low-frequency vibrations. If such intensification occurs, use of available equations to predict peak particle velocities and to design blasting patterns and select blasting parameters could lead to possibly damaging ground shaking.

Jan 1, 2002

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Doug Anderson

Two quantities, Peak Particle Velocity (PPV) and Scaled Distance (SD), have controlled aspects of many blasting projects and operations for a long time. Vibration criteria typically use both PPV and SD because they are simple to measure, and simple to calculate. Their use in regulations worldwide is fairly ubiquitous, in efforts to limit damage to structures in the neighborhood of a blasting operation. PPV and SD are also used to determine likely blast damage effects in mining operations.

Jan 1, 2018

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984