Search Documents

By Yu Yalun, Meng Chuyan, Wang Lin, Wang Deshang

Based on the analysis of problems with wall control blasts in open pits, the essential theoretical basis and technological design of the damping presplit blasts are put forward. After practical application of this method in Nanfen Open Pit China, very good results have been achieved: 1) The rate of decreased vibration is up to 40%; and 2) The damage area of slope is reduced about 60%.

Jan 1, 1998

By James R. Kennedy

The recent drop in world gold prices is driving many northern Nevada underground gold mines to look for new ways to improve and enhance current mining operations. Continuous improvement programs at these mines are finding the means to increase mine productivity while reducing total production cost. This paper looks at developments in the drill and blast program at Independence Mining Company’s Murray mine.

Jan 1, 1999

By Zhang Shixun, Wang Xuguang, Wang Guoli

A massive millisecond blast at an open-pit mine of large scale can be realized by using the blasting technology of pre-loaded explosives, which can enlarge production scale, reduce the frequency of blasting and of large production equipment movement, and raise the production efficiency. The reason why application of this technology is restricted at high sulfide ore deposits of variable and complex geological conditions is that an exothermic reaction will take place when explosives contact sulfide ores, which could lead to accidents such as spontaneous burning and detonation of explosives pre-loaded in boreholes, influencing blasting and production safety. The thermal decomposition reactions of emulsion explosives of different prescriptions in contact with pyrite have been studied by differential thermal analysis (DTA), kinetics parameters calculation and accelerating rate calorimetry (ARC), and on the basis of the above studies, the safety of emulsion explosives used in sulfide mines has been evaluated with the safe contact time of different emulsion explosives with pyrite determined.

Jan 1, 1998

By Kazuyoshi Kawami, Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Koichi Kurokawa, Yuji Wada

When explosives are detonated in the borehole where there is an air gap between the explosive charge and the borehole of inner wall, the shock cave in an air gap travelling ahead of the detonation front sill be generated. This shock wave is called the precursor air shock wave (PAS). The explosive is precompressed by the PAS, and as a result of that the detonation failure occur on occasion. This phenomenon is well known as channel effect.

Jan 1, 1994

By Reynold N. Hoover, Davis S. Shatzer

The Bureau of Alcohol, Tobacco and Firearms (ATF) is responsible for the regulation and enforcement of the explosives laws codified in the Organized Crime Control Act of 1970, Title XI. To meet its responsibilities ATF has special agents, inspectors and specialists who regularly interact with the explosives industry. However, with just over 2,000 special agents and 800 inspectors and specialists, it is difficult to visit the almost 10,000 explosives licensees and permittees in the United States.

Jan 1, 1995

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By Mark William Withey

Blasting safety in surface mining is a necessary industrial goal. Proper techniques and disciplines exercised during the blasting process enhance the probability of achieving that goal.

Jan 1, 1995

By P A. Gibson, J R. Brinkmann

The South African gold mining industry fires approximately 800 000 sloping blastholes daily. A programme aimed at characterizing the stope blasting process is underway in order to identify areas for improvement and to provide blasting related information for the design of mechanized sloping systems.

Jan 1, 1985

By Brent Blanchard

An emergency demolition project related to a bizarre plane crash has reportedly set a new world record for the tallest structure ever explosively demolished. On Sunday, April 22, 2001, 38-year old Gilbert Paquette was killed when his singleengine Cessna 150 struck a 1,217-foot tall communications transmission tower while flying in heavy fog over a remote region of upper Quebec Province.

Jan 1, 2002

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer, John M. Jr Pitlo

Repelling charges are small explosive charges detonated to frighten and drive fish away from a blasting zone just prior to detonation of a major explosive charge. Use of repelling charges has been recommended by natural resource agencies to mitigate the effects of submerged explosives. Blasting companies have used this technique in a "good faith effort" to reduce potential damages to aquatic resources. It has been assumed that noise or pressure generated by the small charge will drive fish from the immediate area, thereby reducing impacts from the much larger and potentially more-damaging blast.

Jan 1, 1997

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By Pierre-Alexandre Abeel, Charles Dowding, Justin Lueker

When blasting is eliminated as a cause of cosmetic cracking, often someone will ask, “If blasting didn’t cause the crack, then what did?” This paper describes detection by remotely operated instrumentation of the new cosmetic crack that was climatologically-induced. The measurement was obtained as a part of the development of Autonomous Crack Measurement (ACM) instruments to measure micro-inch response of cracks to both long-term, climatological, and dynamic, blast vibration effects. The crack occurred in the wall of a structure that was monitored for over 29 months and as such represents one of the longest periods of ACM observation.

Jan 1, 2015

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011