Search Documents

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By K. Sasaki, H. Miki, Y. Muta, T. Hirajima, G. P. W. Suyantara

"Selective flotation of chalcopyrite and molybdenite is continuing problem since its selectivity is not perfect and current NaHS process needs closed system flotation plant because of hydrogen sulfide emission on acidic condition. Some alternative additives investigated as chalcopyrite became hydrophilic and molybdenite kept hydrophobic. XPS analysis indicated chalcopyrite became hydrophilic since iron and copper sulphate, hydroxide was covered on the surface whereas molybdenite kept hydrophobic since only molybdenite can be seen. Flotation experiments of chalcopyrite and molybdenite mixture sample indicated excellent separation that 95% of molybdenite can be recovered as froth and 93% of chalcopyrite can be recovered as sink. Flotation experiments with real bulk flotation concentration indicated similar separation result compared with current NaHS additive system. Possible mechanisms and detailed phenomenon were investigated based on the surface analysis and thermodynamic calculation etc. this alternative additive is easy to handle compared with NaHS since it does not emit effluent gas and commercially preferable.INTRODUCTIONMany copper mine often associates molybdenite (MoS2) as trace mineral. It is important to separate molybdenite and copper mineral efficiently since molybdenite is valuable mineral and also contamination of molybdenite into copper concentrate decrease concentrate value. Conventional separation of copper sulfide and molybdenite has been achieved with sulfide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulfide (Bulatovic, 2010; Ansari and Pawlik, 2007b). However, this current process shows imperfect molybdenite recovery (Liu et al., 2012, Zanin et al., 2009) and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant (Ansari and Pawlik, 2007a). there are still unknown on the effect of depressant NaHS, but one of the theory is NaHS reductant effect. It is worth to investigate the effect of other reductant as depressant on chalcopyrite. On this research, typical reductant, Na2SO3 are added to utilize for selective flotation of chalcopyrite and molybdenite."

Jan 1, 2018

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014

By Gregory Harbort, Sarah K. DeBono, Alan J. Monaghan, Emmanual V. Manlapig

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber.Existing models of bubble-particle collision efficiency are reviewed in respect to the collected information and refinements conducted. The area of maximum bubble-particle collision efficiency is defined. Findings are related to operation within the rotor-stator zone of mechanical flotation cells."

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By Yuqing Feng, Ping Fang, Dezhou Wei, Zichuan Guan, Shuling Gao, Baoyu Cui

"Air core, as an inevitable phenomenon of rotational flow field inside hydrocyclone, has a major impact on hydrocyclone’s separation characteristics. The air core formation process, its structural features and its influencing factors were investigated systematically in this paper. Numerical study on the air core of a f50 mm hydrocyclone was carried out using a commercial computational fluid dynamics (CFD) modelling software package ANSYS/Fluent with the selection of Reynolds Stress Model (RSM) for the turbulence model and Volume of Fluid (VOF) for capturing the air-liquid interface. Physical experiments were conducted under the same geometry and operation conditions and the particle image velocimetry (PIV) technology was used to measure the liquid flow. The CFD results are compared with the experimental measurement with good agreement demonstrated. The air core was formed generally at around 0.7 s, air outsides of the air core was eliminated completely after 1.7 s. The centreline axial velocities and the water blocking hydrocyclone simulations showed that air of the air core entered the hydrocyclone from the underflow area and exhausted from the overflow area, but there was also some air flowing into the air core from the overflow area. The largest swing of the air core occurred on the top of the underflow pipe, and a protuberance similar to the shape of Adam’s apple appeared when the air entered the vortex finder. CFD simulation results also showed that the air core diameter was decided by axial position and parameters of hydrocyclone. The structural parameters have more effects on the air core diameter than the operational parameters."

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014

By Ghislain Bournival, Cagri Emer, Seher Ata

"It is well known among flotation practitioners that the contact angle can be correlated with the amount of material recovered from feed by flotation. The contact angle of solids can easily be modified by the addition of a collector. However, some collectors also have frothing properties thus altering the solid and bubble surface properties simultaneously. To avoid this problem, a technique has previously been used in which silanol groups are attached to the surfaces of the particles, but this method has its own problems. In this work, silica particles with various surface hydrophobicities were prepared using an esterification process. By using alcohols with different hydrocarbon chain lengths, from 4 to 12 carbon atoms, surfaces with a wide range of contact angles could be prepared. The technique was used in the modification of silica particles that were tested in a fluidized bed flotation column, and a laboratory mechanical flotation cell. In parallel experiments, dodecylamine (DDA) was used as a collector. It was found that irrespective of the type of flotation machine and surface preparation method, there was a close correspondence between flotation recovery and the contact angle of the particles. The silanation process has known drawbacks relating to the presence of moisture during the reaction, and the stability of the silane coating after it is been prepared. Esterification does not suffer from these disadvantages. This work has shown that the esterification technique is a robust alternative method for preparing hydrophobic quartz surfaces."

Jan 1, 2014

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014