Search Documents

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By John L. White

The vibro driver/extractor is a machine that grips to a pile and vibrates it up and down. When the vibrating pile is lowered into the ground, all soil around the pile begins to vibrate. A vibrating pile breaks the friction between the pile and the soil, thus allowing it to penetrate the ground. A vibro is usually operated by hoisting it into the air with a crane and then placing it onto the pile. The vibro has hydraulic gripping jaws that are controlled from the ground. Once the operator has successfully lowered the vibro onto the pile, the jaws are closed and locked onto the pile and operations can begin. Please see the drawing below: [ ]

Jan 1, 1990

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor's design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By Tomohiro Yamasaki

"At the pre-construction foundations of the controlled waste disposal site built at the Port of Kinuura, the clayey soil account for the most, and with lesser amounts of sand compaction piles and sand mat. The cement deep mixing method (CDM) was used to improve ground impermeability and to reinforce the foundations on the seawall. Laboratory mixing and testing was performed to determine the appropriate quantities of cement additive for clayey soil, SCP sand, and sand mat. The test results indicated that maintaining the design strength of qu = 1,550 kN/m2 would require C = 100 kg/m3 of cement additive for all three soil types (clayey soil, SCP sand, sand mat). The permeability performance needed to improve ground impermeability assumes a permeability coefficient of K = 1.0×10-6cm/s. And the clayey soil satisfied the performance requirements at C = 100 kg/m3. However, to improve grand impermeability of the SCP sand and sand mat required more than 5% of particles having diameters of less than 75 µm. Thus, in the latter two cases, the required cement adding quantity was C = 250 kg/m3. The test specimens at one to two weeks after the created with a permeability coefficient of K = 10-6cm/s became permeability coefficient of K = 10-7cm/s six week later due to the effects of cement solidification. So the permeability coefficient declined about one order. The permeability coefficient three months later tends to decline continued with a somewhat lower.INTRODUCTIONBetween 2008 and 2011, the Aichi Seaside Environment Center constructed the Kinuura No. 3 offshore controlled waste final disposal site at Taketoyo in Aichi prefecture. (see Figure 1). The disposal site offers a landfill capacity of 5.21 million m3 and measures 472,000 m2 in area, of which some 344,000 m2 is a managed controlled sector enclosed within an impermeable seawall."

Jan 1, 2015

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Clinton O. Rex, Adam S. Hurley, W. Morgan NeSmith

"Hartsfield-Jackson Atlanta International Airport underwent a $1.2 billion dollar expansion project centered on the construction of the new Maynard H. Jackson International Terminal. Passenger access between the new International Terminal and the domestic airport facilities is primarily via underground Automated People Mover (APM) trains. Prior to this expansion, the APM tunnel terminated beneath Concourse E, which previously served all international flights. The new International Terminal is located approximately ½-mile from the previous terminus of the APM tunnel.A paper describing the general approach to excavation support for construction of the entire APM tunnel extension from under Concourse E to the new International Terminal was published by two of the authors (Hurley and NeSmith, 2014). One of the features of note of the approach involved the intersection of the proposed new alignment of the APM tunnel extension under Concourse E with the old terminus. Specifically, the new tunnel extension conflicted with the location of the existing Auger Pressure Grouted (APG) piles supporting four columns in Concourse E. This paper presents design and installation details of the micropile underpinning approach used to support the existing columns to allow for the proposed excavation including the cutting and removal of the existing APG piles, while allowing Concourse E to remain in service during construction.PROJECT DETAILSGeneralThe construction of the APM extension required an excavation support system for a 450-ft long, 55-ft deep excavation across Taxiway Dixie and a 900-ft long, 30-ft deep excavation beneath the basement of existing Concourse E. The excavation under Concourse E required both excavation support and support of the existing columns over the proposed excavation zone. A general overview of the work area is shown on Figure 1."

Jan 1, 2017

By Mark S. Greenleaf, Alec D. Smith, Mary Vittoria-Bertrand, Heather B. Scranton, Jean Louis Z. Locsin

"Rhode Island’s new $163.7 million, 2,265 ft (690 m) long, four-lane Sakonnet River Bridge sits just south of the existing bridge in Portsmouth/Tiverton. The bridge, a critical transportation system link between Massachusetts and Rhode Island, has a steel I-girder main span and concrete New England Bulb Tee approach spans. The foundation work was done between October 2009 and July 2010, and the bridge was completed in February 2014.Foundation design and construction challenges make the project noteworthy. There were thick layers of silty glacial soils with bedrock as deep as 400 ft (122 m) below the waterline, coupled with high foundation capacity demands at the river piers in 50 ft (15 m) of water. The Sakonnet was one of the first major bridge projects in the country to incorporate AASHTO Load and Resistance Factor Design (LRFD) guidelines for foundation design and construction. Because of these and other challenges, the engineers conducted two design-phase load test programs on several foundation elements. These programs were successful and allowed the engineers to adjust the final foundation design prior to the start of construction. During construction, the contractors drove thirty 6 ft (1.8 m) diameter steel pipe piles, each with a novel recessed steel plate insert, to depths of 130 to 200 ft (40 to 61 m) at the three river piers. The insert provided increased resistance of the steel pipe piles and saved about $9 million. Also, 457 14x117 en bearing or friction H-section piles were driven to between 50 and 190 ft (15 to 58 m) at five land piers. All piles were driven relatively close to the existing bridge, which remained in service during construction, due to the project team’s precautionary use of instrumentation and the installation of a jacking system.Area GeologyThe Sakonnet River is up to 60 ft (18 m) deep along the bridge alignment and is underlain by a deep bedrock valley. The bedrock valley is buried by at least 350 ft (107 m) of soil, which includes a complex sequence of interbedded glacial soils (glacial till, glaciolacustrine deposits and glaciofluvial deposits), overlain by geologically recent estuarine deposits. The soils having the greatest impact on the foundation resistance are the glaciolacustrine (fine sandy silt or silt) and glaciofluvial (silty sand with gravel, cobbles, and occasional boulders less than about 2.5 ft [0.8 m] in size). The soil overburden decreases toward the east and west banks of the river, as the bedrock surface rises."

Jan 1, 2015

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Matthew Janes

The new Bow office complex will become the new headquarters of EnCana Corporation, a leading Canadian oil and gas company. The shoring system, encompassing nearly two city blocks and excavated to a depth of 20.5 m, supported surrounding utilities and buildings in downtown Calgary. Past excavations in the area experienced large amounts of rock movement, the mechanics of which were poorly understood. The focus of this paper is the design process and construction results concerning rock movement and the effectiveness of the shoring structure. A lack of information regarding the local in-situ stresses and shear band propagation in the bedrock led to research of case studies in the Calgary area and a peer review from local experts. Several geotechnical scenarios were analyzed using FLAC to account for varying residual rock stresses and the location and composition of weak rock layers suspected of causing shear band movement. Movement characteristics were predicted that would identify the rock deformation mechanic throughout the construction process. A detailed monitoring programme composed of precision monitoring targets, inclinometers, and extensometers was established to provide accuracy and redundancy in establishing the movement of the rock and excavation support structure. The results of the programme were used to identify the rock deformation mechanics and further refine the FLAC analysis. To date, monitoring indicates that localized shear band effect is the leading cause of rock movement. The phenomenon appears to be directionally dependent and strongly correlated to excavation extent.

Jan 1, 2008

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005