Search Documents

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006