Search Documents

By James Su

The Green River Valley in Kent, Washington, is a fast growing area containing retail facilities, warehouse factories and industrial businesses, including the Boeing Space Center. Traffic from Interstate - 5 to the West Valley Highway is highly congested. Accordingly, a new corridor, including a bridge across the Green River, was designed and constructed between 1996 and 1997. This paper presents a case history of the design elements and issues associated with the construction of the pier foundations of the bridge. Subsurface conditions were evaluated using both deep test borings and CPT soundings to evaluate the strength and consolidation properties of the supporting soils. Subsurface conditions consisted of alternating layers of loose and medium dense silty sand and sandy silt. Engineering analysis included an assessment of liquefaction as well as pier supporting capacity and associated settlement. The constructed foundations included 6-foot-diameter piers cased to a depth of 120 feet below the ground surface. The pier casings were driven to the design tip elevation and the soil inside the casing was removed by drilling. Despite performing borings and CPT soundings at specific pier locations, occasional trees, buried thousands of years ago through geologic processes, were surprisingly encountered during pier construction. This presented unique and difficult driving and drilling conditions. During drilling, the water level inside the piers was maintained near the ground surface to create a balance of hydrostatic pressure and prevent boiling of soils the bottom of the casing. After the casings were installed, the soil inside the casing was excavated, the rebar cage was installed and the pier was filled with concrete using treme techniques. Construction of the piers is complete and the completed piers have experienced negligible settlement. Owner: City of Kent Engineering Department Timothy La Porte, Project Manager Kent, Washington General Contractor: Mowat Construction Company, Kirkland, Washington Foundation Contractor: Condon - Johnson & Associates, Inc., Tukwila, Washington

Jan 1, 1998

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989

By Michael D. Justason

...a global perspective... In March of 2000, the Japanese Geotechnical Society added "Rapid Load Testing" to their national standard for pile testing. In the year 2000. it is estimated that there will be more than 500 "Rapid Load Tests" on foundations around the world. ...so what is a "Rapid Load Test", and why is it gaining acceptance and popularity?

Jan 1, 2001

By Bengt Fellenius

The conventional wave equation analysis without control of the representativeness of the parameters to the actual conditions does not provide accurate results. However, the representatives can be vastly improved by means of using the results of monitoring the dynamic response in a pile during driving. Dynamic monitoring displays the interaction of independent strain and acceleration measurements having directly propor­tional response to impacts, but inversely proportional response to re­flections from the soil. Examples are given and the CAPWAP method used to calculate from the measurements the dynamic pile and soil para­meters and mobilized soil resistance is outlined. The dynamic monitoring technique and analysis has been accepted internationally and been incor­porated into Building Codes. The prediction is offered that in five year's time, no major piling project will be undertaken without dynamic monitoring and analysis.

Jan 1, 1984

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002