Search Documents

By Timothy Flaherty

We observed the boiling in the water very close to the water adjacent to where we were drilling. That only happened at the very beginning before it was switched to water flushing. Yes, it was performed with water flush.

Feb 10, 2003

By Gerry Houlahan

"The 2015 Outstanding Project Award (OPA), which recognizes the superior work of DFI members, was awarded for the San Francisco- Oakland Bay Bridge New East Span. The award was presented to representatives from Caltrans and the T.Y. Lin International/Moffatt & Nichol Joint Venture at the DFI 40th Annual Conference on Deep Foundations in Oakland, Calif. A committee selected this project based on size, scope and challenges of the project; degree of innovation and ingenuity exercised; and the uniqueness of the solution to the difficulties of the job. A bridge across the bay between San Francisco and Oakland was proposed as early as 1872, but it took until November 12, 1936, until it became a reality. The bridge spans to the west of Yerba Buena Island were conventional suspension spans, while the east spans used a steel cantilever truss design and simple steel truss spans. This double-deck bridge served the Bay Area well until 1989. In that year, the magnitude 7.1 Loma Prieta earthquake damaged the East Span of the San Francisco-Oakland Bay Bridge. The resulting interruption to service across the bay demonstrated the vital role this bridge plays in the economic and life safety activities of the Bay Area. The project owner, California Department of Transportation (Caltrans), determined that the safest, most cost-effective solution was a total bridge replacement. The Engineer-of-Record, T.Y. Lin International/ Moffatt & Nichol Joint Venture, working closely with Caltrans, the Metropolitan Transportation Commission (MTC) and the California Transportation Commission (CTC), was charged with developing a comprehensive design strategy that met the project’s stringent criteria for seismic safety. These criteria included the new bridge’s designation as a regional Lifeline Structure that must open to emergency traffic shortly after the occurrence of a 1,500-year return period earthquake"

Jan 1, 2015

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Manish Kumar

One of the recent advances in the field of testing of concrete piles is the Non-Destructive testing (NDT) of piles. This paper deals with a specific project where this technique was employed along with an extensive program of conventional testing methods to cross check the results. Conventional testing of the Bored, cast-in-situ piles involved taking full length concrete cores from piles to check physical properties such as core recovery, RQD, crushing strength and density of concrete. Additionally, a number of questionable piles were exposed and inspected and actual load tests were performed on selected piles. Concrete pour cards were used to compare actual Vs theoretical consumption of concrete. A direct comparison of the conclusions drawn from both these testing methods provided an excellent opportunity to better understand the intricacies of NDT technique. The study undertaken clearly indicated a need for developing clear guidelines and specifications for the use of this method of non-destructive testing of piles before the .method can be accepted as a useful quality control tool at the construction sites.

Jan 1, 1996

By Hajialilue Bonab M.

The soil-pile interaction under lateral impact loads is not yet completely well known. Many tests on single piles under static lateral loads in centrifuge have been performed and P-y curves have been determined at different levels of the pile in soil. Following these static tests on piles, a large program is undertaken with the same piles submitted to impact loads. The pile equipped with various pile caps has been impacted under variable amplitudes of shock. The behavior of the pile under different impacts was studied and dynamic parameters of the soil-pile system have been determined. Many cases of loading constituting various load histories have been analyzed. They are resulting from parametric centrifuge tests run out, on the one hand with constant and cumulative impacts and on the other hand, variable and cumulative ones. The Influence of each type of loading was studied. Using a finite element method, a non-linear pile-soil system was conceived and a transient dynamic analysis have been performed. The results of the non-linear analysis and experimental data were compared giving a good agreement.

Jan 1, 2002

By Paul W. Mayne

The axial load-displacement-capacity and load-transfer response of deep foundations can be conveniently assessed by geophysical piezocone tests that provide four independent readings with depth, including tip stress (qt), sleeve friction (fs), porewater pressures (ub), and shear wave velocity (Vs). The penetration data (qt, fs, and ub) of the CPT are utilized to obtain the pile side friction (fp) and end bearing capacity (qb) while the shear wave measurements provide the initial stiffness. Within an elastic continuum framework, the axial pile deflections are calculated and an approximate nonlinear response is obtained by modulus degradation from small-strain response (G0) to intermediate- and large-strains (G). The continuum solution permits separation of load transfer along the sides and proportion to the base. Applications are shown for case studies involving an end-bearing drilled shaft, two friction-type drilled shafts in Alabama and Georgia, and a "Class A" prediction involving driven pipe piles in residuum of the Atlantic Piedmont geology. Load-transfer data were available for the drilled shaft foundations.

Jan 1, 2002

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By Matthew D. Marks

The Sacramento Area Flood Control Agency initiated the Natomas Levee Improvement Program in 2006 which would bring the entire 42 mile Natomas Basin perimeter levee system into compliance with applicable Federal and State standards for levee protecting urban areas. The soil-bentonite slurry cutoff has been utilized as the primary construction method for addressing the under seepage deficiencies. To date, a combined total of over 4,500,000 square feet of slurry cutoff wall have been constructed utilizing excavation methods to a maximum depth of 75 feet and deep soil mixing methods to a depth of 90 feet. The construction of these cutoff walls has required the use of newly designed and custom built long boom and stick attachments for large hydraulic excavators and additional resource will be required to complete future phases. Key components of the NLIP program have included advancements in the development of soil-bentonite backfill mix designs, specified ranges on the soil backfill gradation to address concerns of long term consolidation of the backfill material, evaluation of the trench slurry filtrate loss with regard to cutoff wall acceptance, maintenance high slurry densities to provide greater trench stability, and continued development of backfill mixing procedures.

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010

By Jorj Osterberg

550 load tests of up to 150 MN have been completed on driven and bored piles using the Osterberg Load Cell. Because the test measures side shear and end bearing separately, much can be learned about the forces on the pile as it is loaded to ultimate capacity. At working loads side shear almost always far exceeds end bearing, with the distribution of shear and bearing greatly affected by disturbance occurring during drilling operations. Since much less movement is required to mobilize side shear than end bearing, most of the bearing develops after the working load is exceeded. Thus with insufficient bottom cleaning, safety against excessive settlement can be considerably reduced. Improved methods of drilling, hole cleaning, rebar cage installation and concrete placement are discussed. For rock socket piles it has been found that the ultimate test load far exceeds the working loads in most cases. This is almost always due to greater penetration into the rock than is required for adequate safety against excessive settlement. Factors affecting rock socket capacity are discussed. Increase of side shear and ultimate capacity with time is discussed. Case histories for driven and bored piles in soil and rock sockets are described.

Jan 1, 2001

By Yingcai Han

The dynamic behavior of pile foundations is investigated in both theory and practice. The computation method for vibration of pile foundations and DYNAN computer program are introduced comprehensively. With a model of non-reflective boundary between the near field and far field, the Novak&apos;s method of soil-pile interaction is improved. The dynamic analysis and design of foundation for a reciprocation compressor with driver power 15,000 HP are described to illustrate the computation method of soil-pile interaction. Different design options for the piles are compared to limit the vibration of foundation and produce a safe, economic system. The design with 16 - 0.9 m piles is adopted rather than that with 25-0.5 m piles, since the larger damping is provided by the piles with larger diameter. Both field and laboratory tests were carried out to investigate the soil properties including down hole seismic tests to provide soil shear wave velocities at different depths. The method and procedure used in this study can be applied to the design of pile foundations for tall buildings, bridges and offshore platform with soil-pile interaction under seismic, blast, sea wave and other dynamic loads.

Jan 1, 2002

By Don C. Warrington

This paper describes a new wave equation analysis program called ZWAVE, which is a program specifically for external combustion hammers. The program is de-scribed in detail, the discussion dealing with topics concerning the program such as 1) the numerical method the program uses to integrate the wave equation, which is different from most other wave equation programs; 2) the modelling process of both cushioned and cushionless hammers; 3) the automated generation of mass and spring values for both hammer and pile; 4) the method of dealing with plastic cushions; 5) the use of a recently developed model for computing shaft resistance during driving; 6) the computation and generation of values based on basic soil properties such as shear modulus, Poisson&apos;s Ratio and soil density; 7) the completely interactive method of feeding data to the program; 8) the method used to compute the anticipated rebound and the energy used to plastically deform the soil; and 9) the format of the inter-active input of the program and the program&apos;s output. Sample problems for the program, along with comparison of the program results with data gathered in the field, are presented.

Jan 1, 1988

By Paul J. Lewis

Replacement of the Monroe Street Viaduct in southwest Baltimore City, Maryland included transforming 240 feet of the south approach from a pile-supported multi-span bridge to a mechanically stabilized earth (MSE) embankment supported by vibro-concrete columns (VCCs) and a load transfer platform. The project area was underlain with highly compressible soils which would have resulted in up to 18 inches of settlement under the proposed embankment load. Adjacent structures and critical underground utilities would have been impacteded or damaged by this settlement. Various load transfer alternatives were evaluated to mitigate the anticipated settlement by supporting the embankment on a deeper, more competent stratum. The alternatives considered included compaction grout columns, stone columns, deep soil mixing, and VCCs. Deep soil mixing was eventually selected for design, however, as part of a value engineering proposal, the general contractor Joseph B. Fay Company, with assistance from Hayward Baker and the Collin Group, prepared and submitted an alternative consisting of VCCs. This paper presents the details of the value load transfer platform and VCC design. Loading tests were utilized to confirm the VCC capacity and field changes were implemented based on the test results.

Jan 1, 2007

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Sherrill Gardner

Vibratory drivers have been used since the 1930s to drive and extract piles. Vibratory pile drivers have the capability of significantly decreasing pile installation time, especially in granular type soils. However, they have not been widely accepted because of the uncertainty in estimating the bearing capacity of the driven pile. When driving bearing piles, the industry standard method for obtaining load carrying capacity of a pile installed with a vibratory driver is to redrive with an impact hammer. The advantage of improved productivity is lost with the redrive procedure. Currently, there is no other method to predict the capacity of these bearing piles installed with a vibratory driver. The Naval Civil Engineering Laboratory (NCEL) is making progress towards being able to estimate the bearing capacity of these piles. This paper describes field testing and corresponding analytical modeling of the vibratory driver-pile-soil system. The following sections describe the development of the numerical model and techniques for collecting field data. A discussion of the prediction of the pile driving process based on field test data is followed by suggestions as to the additional work that should be done to further verify the model to a point where it can be used with confidence.

Jan 1, 1987