Search Documents

By Maureen A. McGuinness

Kidd Mine, an Xstrata Copper operation in Timmins, Ontario, operates a 400 t/h pastefill plant that provides paste backfill to stopes at the depth of 9000 ft. This paper will cover the operating practices of the pastefill plant both on surface and underground, highlighting tailings excavation, paste mix design and the pipe maintenance program. Kidd Mine, une opération d'Xstrata Copper à Timmins, Ontario, opère une usine de remblai d'une capacité de 400 t/h. Le réseau de distribution permet d'acheminer le remblai en pâte juste qu'à une profondeur de 9000 pi. Cet article couvrira le mode opératoire de l'usine de remblai tant à la surface que sous-terre en mettant l'emphase sur l'extraction des rejets miniers, la recette du remblai en pâte ainsi que le programme d'entretient du réseau de distribution.

Feb 1, 2008

By L. Bichler, C. J. Verdon

In this work, the effect of doping yttria stabilized zirconia (YSZ) with 5, 10 and 15 mol% erbium oxide (Er2O3, erbia) was investigated using spark plasma sintering (SPS) technique. Sintering was carried out at 1300°C with 30 and 60MPa uniaxial pressures and a 5min hold time. Densification kinetics were studied using displacement response from the SPS machine. As-sintered microstructure characterization was carried out via scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques, while chemical composition was characterized by energy dispersive X-ray spectroscopy (EDS). The results suggest that sintering carried out at 60MPa produced high density composites even though erbia dopants were found to inhibit material densification and grain growth during sintering. 5, 10 and 15mol% erbia- YSZ had cubic crystal structures, as verified by XRD analysis.

Jan 1, 2014

By C. G. Anderson

Alkaline sulfide leaching technology (i.e. ASL) has been studied, presented and published throughout the literature and utilized in some current engineering studies. Yet, the actual industrial applications are very few and the knowledge about these is very limited. Hence, a large gap between the laboratory, publications, engineering studies, and the actual industrial plant exists. Recent studies of ASL applied to copper enargite concentrates definitively bear out this dichotomy. Hence, this paper will seek to dispel the common misperceptions that continue to surround the selective industrial ASL hydrometallurgical technology. For edification of the reader, a listing of ten common misconceptions and myths is listed. As well, ASL history, fundamental aspects and a new flowsheet application for simultaneous gold and high purity antimony oxide production from low grade materials is included. The associated estimated economic considerations are also included to heighten enlightenment about the application of this industrially proven technology.

Jan 1, 2014

By A. D. Akerman, D. D. Young, G. R. Baiden

The development and maintenance of underground roadways are increasingly important aspects of the modern mining process. With the trend toward automation and track-less mining, roadbeds capable of with standing increased wheel loading have proven necessary to maintain high vehicle speed and reduced maintenance costs. Concrete has been used successfully on some roadways in order to obtain the required characteristics. However, this solution usually involves unacceptable expense. The objective of the Road Router project was to create a drift floor profiling machine capable of cutting a smooth surface out of the existing rock floor of development drifts and ramps. This surface would provide a durable, high strength, low rolling resistance roadbed that would allow for reduced operating cycle times and lower maintenance costs of scoops and haulage trucks. The Road Router has the potential to offer an alternative to concrete with substantial cost savings.

Jan 1, 1997

By Lawrence B. Cochrane, Olivier Tavchandjian, J. Michael Anderson, Christopher R. Davis

"Abstract - Resource modelling is a complex process involving different specialists with relevant experience using a multi-disciplinary approach and the best available technology and reviews by independent auditors. The reliability of the final resource estimate is highly dependent on the quality control exercised at each stage of the process. At each step in the resource modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. Designation of responsibility and authority for meeting these objectives must also be clearly identified. External audits must also be incorporated to review and validate the implementation of new procedures.Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting, classification, and risk analysis."

Jan 1, 2001

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By D. Sammut, F. Houllis, J-L. Huens, J. Moyes

The Intec Gold Process has been developed as a halide-based alternative for the recovery of gold from refractory sulphide deposits. The halide medium allows sulphide oxidation and gold extraction to be performed concurrently at moderate temperature and atmospheric pressure sourcing oxygen from direct air injection. The dissolved gold is loaded onto activated carbon and stripped in a conventional Zadra circuit. High gold extractions have been achieved from a range of refractory gold concentrates at laboratory scale, which has led to a continuous locked-cycle pilot plant program. The pilot plant operated at >99% availability, with a maximum of 96.5% gold extraction from a concentrate containing 58.6 g/t gold. >99% of the dissolved gold was loaded onto carbon at up to 1% w/w, with no loss of carbon activity detected over five loading/washing/elution cycles. This paper describes the process and presents both laboratory and pilot plant results as well as economic data from two costing studies.

Jan 1, 2005

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By M. Knot

Fans delivered to the Russian Federation, and eventually to countries of the former U.S.S.R., for mine ventilation must meet the legislative requirements of local jurisdictions. This paper presents a discussion of these legislative requirements and presents examples of fan equipment designed to meet the requirements. The legislative obligations discussed include four (4) separate requirements, including: ?Technical design requirements ? The Federal Agency for Technical Regulation and Metrology is responsible to issue a GOST R certification declaring conformance to the requirements ?Operational requirements ? A ?License for Application? must be obtained prior to operation ?Explosion risk requirements ? If the area of operation includes potential for explosion a special certificate must be obtained ?Technical condition requirements ? Market segments within the mining industry require special conditions that must be satisfied Examples of fans designed specifically for use in the Russian Federation are also discussed and examples provided. Designs for fan volume flow control will be highlighted.

Aug 1, 2013

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By Hyumng Sup Choi

The role of the interfacial electrical 'Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010