Search Documents

By Sheila E. Daniel

"Since 1989, the Mine Environmental Neutral Drainage Program (MEND) has sponsored research into ways of reducing the environmental impact and financial liabilities associated with Acid Mine Drainage from tailings and waste rock. Toward this overall objective, Kilborn was contracted to review the use and applicability of passive treatment systems for acid mine drainage.Experimentation using passive systems to treat acid mine drainage has been ongoing since the early 1980's in North America. Passive treatments are generally considered an attractive alternative to active lime treatment, since they require minimal human involvement, no power, and only seasonal or periodic care and maintenance after establishment. Most attractive is that initial capital cost to implement a passive treatement system is generally low to moderate. Ongoing operating costs are similarly low when compared to active treatment systems.Passive treatment systems currently used, or under investigation to treat acid mine drainage include: anoxic limestone drains, aerobic wetlands, reed bed wetlands, compost wetlands, microbial systems and bioabsorption systems. These wastewater treatment systems utilize the chemical, biological and physical removal processes that occur naturally in the environment to improve wastewater quality, including: oxidation, reduction, coagulation, adsorption, absorption and precipitation; microbial activity; and, gravity aeration and dilution. The rates at which these processes occur determines the loading which can be treated and the effectiveness of the system.The results of our literature review will be summarized, and insight provided into the applicability of passive systems to treat acid mine drainage from Canadian Mines."

Jan 1, 1995

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By Robert B. Parsons

"Canada doesn't really have a tax system for mining - it has eleven separate tax systems! The consequent maze adds some undefinable margin of difficulty to making investment decisions in Canada. But, this 11U1Ze is not likely to be simplified. Solution: learn it and sell it! Intricate Network of Winding PathwaysWebster's New World Dictionary defines the word ""maze"" as follows: ""a confusing, intricate network of winding pathways; labyrinth ... a state of confusion or bewilderment"". Webster's does not go on to give an example of a maze, but the dictionary could easily have referred to the taxation of a Canadian mining operation. The uninitiated would almost certainly look upon such taxation as a maze of the most perplexing sort.Twenty years ago, Canada's tax system was really quite simple. It is true that Canadian mining profits were subject to three levels of taxation (federal income tax, provincial income tax, and provincial mining tax), but this didn't pose a problem. Prior to 1974, at least the provincial income tax systems were somewhat the same in terms of rules .and rates, and even the provincial mining tax systems resembled one another. Mining profits were subject to pretty much the same rules, no matter what province or territory hosted the mine. Those were the “good old days” one could even dare to generalize about tax rates without fear of being labelled an imbecile!"

Jan 1, 1994

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By D. Nikols, G. Caraghiaur, P. C. Roxburgh

"IntroductionThe Highvale Mine is located 70 km west of Edmonton , Alberta on the south side of Lake Wabamun. It has been developed by TransAlta Utilities Corporation as a captive mine to supply fuel to two genera ting power plant s. The mine is owned by TransAlta and operated under contract by Manalta Coal. Within the mine permit area, TransAlta own s the right to mine 80% of the recoverable surface mineable coal.The planning process starts with the annually produced 25-year energy forecast which is provided by the Electric Utility Planning Council (EUPC). A 1983 forecast predicts an average annual increase in energy requirements of 4% over the next 25 years. Put another way, the requirement will double before the end of the century. A lar ge part of the base load generation of the Province of Alberta is provided by th e plants fueled from Highvale Mine. The Highvale Mine is therefore expected to maintain a high output over a long period of time.Mine PlanningMine planning is an ongoing, interative process that draws from many sources. All levels of planning draw from the same sources but du e to the different processes and objectives of each planning class, the degree of influence may differ. The planner becomes then a coordinator bringing together data and excerpts from several disciplines in groups. Generally, there are four classes of mining plan s; these are all used at the Highvale Mine (Table I)."

Jan 1, 1986

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By C. J. Kerr

"A recent information sheet from the Mining Health and Safety Branch of the Ontario Ministry of Labour was sent to all Ministry inspectors and engineers. The subject title was' 'Two Brakes on a Hoist Carrying Persons"" and it quotes mining regulation 699, sub-section 206(i):No hoist shall be used for the transporting of persons unless it has a braking system consisting of at least two sets of mechanical brakes to stop and hold the drum for the shaft conveyance transporting the persons.The intent of the regulation is that each of these brakes is to be set so that, individually, they can safely stop the drum carrying persons and also hold the drum without movement with the maximum manload.This can be achieved in the following ways: Single Drum Hoist-one brake on each side of the drum, one brake on the drum, one brake on the pinion shaft, where disc brakes are used two separate disc brake assemblies on the disc. Double Drum Hoist, brakes on companion drum can serve as backup brake only pinion brake with one drum unclutched.Friction Hoist, one brake on each side of drum As new hoists can be manufactured easily with a two-brake system, attention will be focused on retrofitting pinion brakes to older hoists.A brake mounted on a pinion shaft is designed purely as an emergency brake in the event of main brake failure , controls malfunction, and power loss."

Jan 1, 1989

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world's most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7'3 of Indonesia's people reside on Java, or on 70/0 of the country's land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

The Project ? $1.4 billion project ? 59,000 tonnes of nickel and cobalt ? Large resource base ? First production end of 2004 The Place ? Half the size of Vancouver Island ? Population 210,000 ? 43% Melanesian, 37% European, 12% other South Pacific groups, 8% other nationalities ? Tourism principal industry ? 1/3 of world?s nickel resources The Politics ? French Overseas Territory ?1998 Noumea Accord: increased local control over domestic policy ? Referendum on independence in 2014 ? Seeking more economic autonomy, less dependence on French support

May 1, 2002

By H. Polkowska-Motrenko

Analytical methods for the determination of uranium and other precious elements in ores, industrial wastes and by-products have been developed. The analytical techniques employed are NAA and ICP-MS. Two procedures of digestion were applied: microwave acid digestion and alkali fusion. Accuracy was checked by using CRMs. Results of analysis of the same samples by the elaborated methods have been presented and compared. The methods will be used for estimating the capacity of uranium production for the Polish nuclear power programme.

Aug 1, 2010

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By Michael Samis

NOFLEX valuation results ? CF deviations and net CF risk discount factors ??Cash flow deviations indicate average cash flow variability. ??Net cash flow riskdiscount factors (NCFRDFs) indicate the size of the risk adjustment applied to a cash flow. NCFRDFs profile should change with variations in cash flow uncertainty since the risk adjustments applied to the project cash flow reflect investor sensitivity to uncertainty.?DCF and RO will often produce different NCFRDFs for the same project since they use different methods of risk-adjustment.

May 1, 2006

By P. E. Georghiou, S. Shafiei Zadeh, H. Hassan Nejad

Data are presented on the extractant behaviour on toxic metal removal from spent hydroprocessing catalyst, produced at the North Atlantic Refinery plant in Newfoundland and Labrador. Aliquat 336 was selected due to its potential capabilities for the separation of cobalt, molybdenum and nickel from the leachate extractant produced by aqua regia. The solvent extraction process was statistically modeled using central composite design (CCD), and the numerical optimization was conducted to achieve the optimum point for toxic metal recovery for the extractant.

Jan 1, 2014

By G. L. Spence

Prevention of cuprous and cupric oxide formation on stored ETP copper rod is a major concern for copper rod and wire producers. During normal storage periods copper oxide layers can increase from less then 100 A to more then 1000 A exceeding ASTM specifications and discoloring the rod surface. Various types of corrosion inhibitors are tested and compared in effectiveness for prevention of copper oxide formation on stored copper rod. Aromatic triazole compounds are also compared to a non-azole containing compound.

Jan 1, 2007

By M. Jahazi, M. Brochu

This paper describes the advantages/disadvantages of electron beam freeforming using two different types of filler metal: (1) brazing paste and (2) solid wire. Sound buildups were obtained from both filler metal. The freeforms produced with the brazing paste showed a certain level of porosity, which was reduced by successive melting. In comparison, the solid wire buildup was practically free of pore. When compared with the solid wire filler, the brazing paste produced narrower buildups but a larger scattering of the width.

Jan 1, 2004

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By Scott Hommema

? Bitumen in the oil sand averages Bitumen 12 wt%; water makes up 4 wt% ? Imperial Oil (operator) and ExxonMobil developing Kearl Leases #6, 36, 87 (~200 sq. km) ? Target resource > 4 Billion Barrels ? 3 Phase development, ~100 kbd per phase High-quality resource ? Surface mineable bitumen ? Average properties (full lease) ? TV:BIP < 8 ? Grade > 12 wt% bitumen ? Ore thickness of 40 m ? Overburden thickness of 20 m Status ? Phase 1 ? Front end engineering and design underway ? Detailed engineering to start 2008

May 1, 2008

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men&apos;s hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931