Search Documents

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson?s ratio, P-wave, Swave velocity, point load test index, crushing and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with low strength detonating cord, to combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

May 1, 2003

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is located within a porphyry copper deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between TeckCominco with a 63.9% interest, BHP Billiton holding 33.6%, and others 2.5%. Management is shared by the two principal owners and directed by a management committee.

May 1, 2003

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By Tiago Webber

Mineral resources estimation comprises basically two stages: (i) data collection, analysis and validation, and (ii) the estimate of the grades and tones of the deposit. The most applied method for sampling survey in mineral exploration is rotary drilling with total core recovery. High drilling costs make borehole geophysical logging attractive to obtain the maximum possible information from each borehole helping to understand ore intersections, grades variability, limits of the deposits and continuity of the mineralization. In this paper, borehole geophysical logging was used to enhance the sampling survey and to derive grades indirectly (without lab analysis) with a certain amount of uncertainty. Indicator kriging (IK) was the estimation method used, as it is adequate to incorporate the uncertainty associated with the geophysical derived grade values. The results were compared to the conventional procedures using grades determined via core analysis and ordinary kriging. Borehole geophysical logging proved to be efficient to define the essential features of ore deposit and IK provided results with acceptable precision and accuracy if compared to the model provided by ordinary kriging.

Oct 1, 2009

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

Accurately modeling and predicting long term mill throughput is one of the challenges facing metallurgists, geologists and mine engineers in their quest to consistently deliver accurate life of mine business plans. Batu Hijau has systematically improved long and short term mill throughput predictions since feasibility and commissioning in 1999. This has been achieved through a combination of ongoing improvement to the geology ore hardness and grade characterisation model, drill and blast optimisation and, by application of these data to model mill throughput. Batu Hijau has demonstrated the ability to consistently estimate long term mill throughput within ±2% accuracy. Aside from reliably predicting expected production rates with the existing plant configuration, this predictive ability provides a solid foundation for identifying operating and design criteria for short term grinding circuit optimisation and future expansions. This paper discusses ongoing throughput prediction model development at Batu Hijau based on geo-metallurgical characterisation. Also discussed are tools used for day to day production performance management. This includes on line "Mine to Mill" variable monitoring to improve operations parameter ecision making and performance assessment.

Nov 1, 2011

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By F. Wirfiyata

"Accurately modeling and predicting long term mill throughput is one of the challenges facing metallurgists, geologists and mine engineers in their quest to consistently deliver accurate life of mine business plans.Batu Hijau has systematically improved long and short term mill throughput predictions since feasibility and commissioning in 1999. This has been achieved through a combination of ongoing improvement to the geology ore hardness and grade characterisation model, drill and blast optimisation and, by application of these data to model mill throughput.Batu Hijau has demonstrated the ability to consistently estimate long term mill throughput within ±2% accuracy. Aside from reliably predicting expected production rates with the existing plant configuration, this predictive ability provides a solid foundation for identifying operating and design criteria for short term grinding circuit optimisation and future expansions.This paper discusses ongoing throughput prediction model development at Batu Hijau based on geo-metallurgical characterisation. Also discussed are tools used for day to day production performance management. This includes on line ""Mine to Mill"" variable monitoring to improve operations parameter decision making and performance assessment."

Jan 1, 2012

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Paul Johnston

or is it? Mining Automated Loader Technology Application ? Intelligent software mounted in hardware on a remotely controlled scoop. ? Led by INCO, Sudbury, with ? C-CORE, St. John?s ? Automated Mining Systems, Aurora ? Bell Canada, Sudbury ? Laurentian University, Sudbury ? University of Western Ontario, London Completed: March 2000

May 1, 2008

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By Éric Côté

Introduction The 425 Main Ore Zone ? Block of ore partially mined in the late sixties; ? Area was sealed off for over 30 years due to SO2 emissions from oxidizing fill material; 425 Project goal ? Bring the zone back into production without jeopardizing the mine; ? Minimize risks associated to SO2;

Feb 1, 2008

By J. H. Curran

Agenda ? Challenges of developed world mining ? Software aids for creative and practical engineering ? Rocscience software philosophy ? Rocscience suite of geomechanics programs ? Case study ? design of de-stress slot Mining Challenges of the Developed World ? Dwindling reserves ? Great depths ? Strict operating and environmental regulations ? Competition from lower cost operations in developing countries

Apr 1, 2005

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016