Search Documents

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By The Staff

"A general description of the equipment, personnel and work sequence •being used in the sinking of a circular, concrete lined, 14 foot diameter shaft which at present is at a depth of 2,484 feet. Equipping, lining and sinking of the shaft is being carried out concurrently and waste is re-moved using a mechanical mucker.INTRODUCTIONTHE BUCHANS UNIT of the American Smelting and Refining Company operates a group of mines at Buchans, Newfoundland. Buchans is in the centre of the Province (Lat. 48°47'N.; Long. 56°50'W.), five miles north of Red Indian lake at an elevation of 900 feet and is accessible by 37 miles <Jf private railway which connects with the Canadian National railway at Millertown Junction, and by 47 miles of gravel highway, which connects with the Trans-'Canada Highway at Badger."

Jan 1, 1959

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By L. G. Smith, C. A. Shook, W. H. W. Husband, W. Schriek

"The flow of slurries in pipelines is governed by many variables, and the study of the influence of each of these variables is difficult, if not impossible, in some cases. Many correlations are available which fit data within a given range. However, no one method is yet available to design a slurry pipeline for all desired conditions without at least some physical measurements on the slurry itself. For this reason, the slurry pipeline facilities at the Saskatchewan Research Council have been developed during the past 12 years and it is hoped that the development will continue until the process is thoroughly understood and test facilities are no longer necessary. This paper outlines methods currently used and under development at the Saskatchewan Research Council for measurement, control and study of the variables governing the flow of slurries."

Jan 1, 1973

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By A. McIntyre, L. R. Plitt

Both the Bond and the Hardgrove grindability tests are widely used in the mineral industry to measure the ease of the comminution displayed by a material. The Hardgrove test is mainly used for coals, whereas the Bond grindabifity test is mainly applied to hardrock minerals. The Bond grindability has the advantage that it can be empirically related to the energy required for comminution (work index), whereas the Hardgrove grindabifity test has the advantage of being easier to perform. In an effort to establish a valid correlation between work index and Hardgrove grindability, a series of parallel grindability tests were carried out on a wide variety of rocks and minerals. The standard Hardgrove test was modified to allow for materials with a higher density than coal. A new, satisfactory relationship was established which permits rapid estimation of work index from Hardgrove test data.

Jan 1, 1980

By N. Verbaan, Ph. Henry, S. Lamotte

Hydrometal(lurgy) provides an adequate technology to reintroduce otherwise lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Three case studies at an integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed. (1) Non-ferrous leach residues are treated by a leach-SX process to recover their minor metals (Ge) contents. The remaining acid waste solution is used by the fertilizer industry nearby. (2) Residual low quality acid and caustic are used in the processing of zinc industry cements to produce copper, nickel, cobalt and zinc concentrates by several consecutive selective leach - precipitation processes. (3) Copper anode slimes are treated and their precious metal contents are recovered. Depending on the composition of the slimes, separate or combined concentrates of copper, bismuth, tellurium/selenium and silver/precious metals can be produced.

Jan 1, 2004

By Raj Thamburaj, Li. Ping, Prakash C. Patnaik

"An effective prognosis system for aircraft engines may involve the application of a wide range of technologies and methodologies, which may include: - On-line, real-time and in-situ non-destructive inspection/detection/sensoring - Aircraft/engine instrumentation - Airborne data recording system - Advanced signal filtration - Data compression technologies - On-line engine health monitoring technologies - On-line engine component life usage monitoring technologies - Mission severity analysis algorithm based on life prediction and damage tolerance analysis models - Life assessment methodologies - Optimized repair/overhaul/maintenance planning - Optimization of mission assignment and homogeneous life usage - Web-enabled information delivery and sharing system - Decision making logistics This paper will demonstrate some efforts that Orenda has accomplished over the last decade in collaboration with the Institute for Aerospace Research of National Research Council Canada and the Department of National Defense. The presentation will focus on the following projects:"

Jan 1, 2004

By D. M. Bastidas

The reduction of copper sulfide and copper oxides originated during artificial tarnishing of copper was studied using potentiodynamic potential/current density experiments. Six copper surface treatments were considered: mechanical polishing; indoor exposure for 7 days; chemical etching in 1.6 M nitric acid; chemical etching and heating at 160°C; and chemical etching and dipping in a 9x10-4 M or 0.9 M potassium sulfide (1(25) solution at 70°C. Cuprite (Cu20) and chalcocite (Cu2S) were the main compounds formed. A linear relationship with the square root of the scan rate (v) was obtained by plotting the potentiodynamic potential/current density for the tarnish dissolution processes. A relationship between potential and current density cathodic peaks was not obtained, according to Müller&apos;s model, showing a proportionality factor with the dimensions of a resistance.

Jan 1, 2007

By T. H. Etsell, P. C. Holloway

The fly ash produced by oil sands operations in northern Alberta represents a large, high-grade, potential resource for vanadium production in Canada. After extensive batch testing at the University of Alberta, a conceptual process flowsheet for the recovery of vanadium from oil sands fly ash has been developed. The various unit operations for this process, including decarbonization, roasting, leaching, desilication, precipitation, salt recovery and byproduct recovery, are described. Processes for the recovery of molybdenum and ammonium chloride from waste streams from this process, are proposed, as are potential uses for the ash residue; these byproducts represent significant potential sources of secondary revenue while reducing the environmental impact from the process. A preliminary economic analysis for vanadium recovery from oil sands fly ash using this process is also included and several major economic factors influencing its commercialization are discussed.

Jan 1, 2004

By A. Bouajila

To stay competitive in an open market, mineral industries have to optimise their processes, lower their production costs and improve the commercial value of their products. Up to a recent past, they were impaired in this attempt by a lack of adequate devices allowing reliable on-line and real-time process monitoring (detection or measurement). Process monitoring for process control and the product characterisation for quality control are quite different tasks. Planners and researchers should be fully aware of this when evaluating or developing monitoring equipment for on-line process control. This paper will comment on some aspects of sensor specifications, during the design and the evaluation steps, related to sampling, measurement (accuracy, sensitivity, delay and correlation to the process) and suitability to the exploitation environment. Examples of R&D projects promoted by COREM for various industrial applications will be presented.

May 1, 2001

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By Lee W. T. Weitzel

This paper reviews the Falconbridge- SMRQ?s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40km property strike length. As a result of its remote northern location other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel based financial spreadsheet to bring the total plan together. The focus of this paper is to show the complexity of modern mine planning and associated economic modeling of mine processes.

May 1, 2002

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970&apos;s, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By Louise Laverdure

Outline ?Background ?Issues and considerations ?Why do we need to innovate ?Green Mining Initiative ?Footprint reduction ?Innovation in waste management ?Ecosystem risk management ?Mine closure and rehabilitation ?The Future

May 1, 2011