Search Documents

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By C. A. Rowland

"Plant owners and operators, plant designers and grinding mill manufacturers are giving much attention to the design and manufacture of autogenous and semi-autogenous grinding mills, particularly the mills that have large diameters and draw power up to 10,000 hp and greater. Reliable designs giving long operating lives are required in today 's ore processing plants.This paper reviews bench-scale and pilot-plant testing to determine first if the ore is suitable .to be ground by these methods and then reviews the data obtained from pilot-plant testing that is used to select the mills and the grinding circuit. The paper then discusses the use of the pilot-plant results to design the mills. The most important pilot-plant data used for mill design are power and the amount of ball charge to be used. The mill size selected is a combination of these factors. Pilot-plant data not only establish power requirements, but can be used in the selection of the type of drive, variable speed or fixed speed, and the operating procedure to be followed. This leads into the mill control circuit to be used. The total charge in the mill, the type of drive and mill discharge arrangements are needed in the calculation of stresses and bearing loads. Conclusions reached from pilot-plant work are used to obtain data for process design, and autogenous and semiautogenous mill design should be part of any test program incorporating either or both of these grinding methods."

Jan 1, 1981

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By J. A. Reid

THE views and observations expressed herein on this old but constantly recurring question are our own, no effort having been made to align them with standard texts. Therefore, while they may find general acceptance amongst fellow engineers, they must stand as personal opinions and as such are open to debate and discussion. In order properly to consider the subject, it should first be 'set in proper perspective. Why are Prospects Examined? Prospects are examined to determine whether they may contain economic concentrations of metals or minerals, the legitimate mining business being run, pretty largely, to make money. Next to food and clothing, modern civilization is based on metals, with which are included in this discussion minerals, oils, and fuels. A constant and increasing demand for the common metals requires the location of replacements for depleted orebodies, while the use and appreciation of new metals brings increasing demand for them. Aluminium is a good example of a metal which has, within recent years, made great progress. Today, we are becoming increasingly aware of magnesium, chromium, tungsten, thallium, and other lesser known, metals.

Jan 1, 1945

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By J. Sadaki, G. Dodbiba, S. Murakami, T. Fujita, S. Matsuo, H. Ono, K. Okaya

Printed circuit boards (PCBs) from discarded personal computer (PC) and household appliances were crushed by mechanical crushing or water explosion to remove mounted parts. More parts were stripped from PCB for PC composed of epoxy resin than from PCB for household appliance composed of phenol resin. In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 1073K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment. On the other hand, tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723 to 773K in air atmosphere and screening of 0.5mm. Silica was removed and 70% of tantalum grade was obtained after more than 823K heating and separation.

Jan 1, 2011

By Robert D. Brown

"On April 22, 1980, the Ontario government introduced a totally new incentive program for mineral exploration in the province to be effective September I, 1980. Replacing the former Mineral Exploration Assistance Program (MEAP) and also the assistance formerly provided to the mining sector under the Small Business Development Corporations Act, the new Ontario Mineral Exploration Program (OMEP) promises to offer a valuable benefit to certain eligible applicants.Unfortunately, the program is not without its shortcomings: the eligibility for grants or tax credits under the program is comparatively restrictive, and an October 1980 federal budget provision to amend income tax legislation would blunt some of the originally intended attractiveness of the grants and credits.IntroductionIn his budget of April 22, 1980, Ontario Treasurer Frank Miller introduced a new incentive program to encourage mineral exploration in the province.The Ontario Mineral Exploration Program (OMEP) replaces the Mineral Exploration Assistance Program (MEAP), which will be phased out by March 31, 1981. Exploration programs approved under MEAP will continue to qualify for incentives under that program, but will not qualify for OMEP."

Jan 1, 1981

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By M. Duncan

Lightweight, high-pressure cylinders for compressed hydrogen storage are essential components for fuel cell vehicles. Storage volume and mass are two key considerations. Current on-board hydrogen storage systems are based on a maximum pressure of 350 bar. While 350 bar systems are excellent solutions for many applications, some situations require higher storage densities due to space restrictions. As a result, significant research and development work has been expended by cylinder manufacturers, systems providers, testing agencies and automotive manufacturers to develop 700 bar systems with reduced storage volumes. Dynetek Industries Ltd. has proactively developed several 700 bar storage cylinders based on a seamless aluminum liner over wrapped with a carbon fiber composite. This paper presents the challenges and processes involved in the design, testing and certification for Dynetek Industries Ltd. 700 bar cylinders. This paper also provides reasoning for further volume and mass optimization of compressed hydrogen cylinders through the establishment of realistic cylinder usage parameters in standards. In particular, the overly conservative fill life requirement for cylinders is examined.

Jan 1, 2005

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By L. S. Trenholme

"Belleterre Quebec Mines, Limited, is a subsidiary of Mcintyre Porcupine Mines, Limited. The property is in Guillet township, Quebec, 45 miles due east of Haileybury, Ontario. It is accessible by 72 miles of gravelled road from New Liskeard, Ontario (Fig. 1).Gold production at the property commenced in 1936 and to March 31st, 1945, had exceeded $9,000,000. For the past 3 years the milling rate has averaged 325 tons a day and the gold recovery about $14 a ton.GENERAL GEOLOGYThe rocks of the district consist of Keewatin-like volcanics conformably overlain by Timiskaming-like sediments. Together they form the remnant of an easterly plunging anticline engulfed by granite (Fig. 2). The pregranite intrusives consist of diorite, gabbro, and ultrabasic rocks, occurring as dykes, sills, and irregular stocks. Dykes of porphyry and lamprophyre presumably related to the batholithic intrusive are common in this area. The veins of quartz are also probably derived from the batholithic intrusives. A few dykes of Keweenawan-type diabase have been observed."

Jan 1, 1954

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By Al Hoffman

During the period May 15 ? 17, 2006 four fatalities occurred at #1 Waste Dump, at Teck Cominco?s Sullivan mine located at the city boundary of Kimberley, British Columbia, Canada. The fatalities occurred in the sump of a water monitoring station. The Chief Inspector of Mines and his staff immediately responded to the incident. The team worked collaboratively with the Teck Ltd. Trail Hazmat team, a consultant group from Rescan Ltd. and other Teck operation and technical staff. Sampling in and around the water monitoring station in the days following the fatalities showed that exposure to a depleted oxygen environment was the immediate cause of the fatalities. The sump located at the base of the shed was hydraulically connected to a French (coarse rock) drain, located at the toe of the covered waste dump. This presentation will briefly review the immediate cause of the accident, the investigation, a brief introduction to the work of the Sullivan Technical panel and the British Columbia government?s response to the incident and the recommendations of the Coroner?s inquest.

May 1, 2010

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-l993. Part I, presented in the June 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of these considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows;A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothennal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;0G. Diverse Hydrothermal Deposits, Sediment-hosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration GeophysicsAbstracts related to themes A. B and C are presented in this issue; the remaining abstracts will be presented in future issues."

Jan 1, 1994

By Kostas Fytas

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

May 1, 2001

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994