Search Documents

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

By M. Leroux, S. R. Rao, J. Kim, J. A. Finch

"Continuous in-plant testing of collectorless Cu/Pb bulk flotation on Lyon Lake ore at Matlabi Mines Ltd. Was conducted using a portable circuit based on 5 L mini flotation cells. It is concluded that collectorless Cu/Pb flotation is a reliable phenomenon for this ore over the usual range of plant operating conditions.IntroductionFlotation of some sulphide minerals without the use of conventional collectors (e.g. xanthates) is now widely recognized. The requirement appears to be some degree of oxidation, although the nature of the surface product formed is still uncertain (Luttrell and Yoon, 1984; Buckley and Walker, 1988). The phenomenon has been termed ""collectorless"" or ""self-induced"" flotation. One of the minerals most responsive to coUectorless flotation is chalcopyrite; in contrast pyrite and sphalerite show little response and galena usually shows intermediate response (Hayes et al., 1987; Shannon and Trahar, 1986).Most of the work on collector1ess l1otation has involved single mineral or batch flotation on ore samples. There are only occasional references to collector1ess l1otation under plant conditions (Sandstrom and Jonsson, 1988; Vargas, 1990; Boyce et al., 1970). Creating and maintaining the appropriate oxidation conditions and differences in water quality are among the reasons why the phenomenon may not transfer readily to the plant (Grano et al., 1990). Periodically from the spring of 1989, Mattabi Mines Ltd. ran full-scale tests of collector1ess bulk CulPb flotation while treating Lyon Lake ore*: the observations confirmed the laboratory finding that chalcopyrite and galena floated without collector (Leroux et al., 1989).To explore this finding continuous in-plant testing using mini flotation cells was conducted which is the subject of this paper. The main objective was to determine if collectorless flotation was a reliable phenomenon over the expected range of redox conditions in the feed pulp to bulk CulPb roughing. As background, the previous work (Leroux et al., 1989; Martin, 1988) is briefly reviewed."

Jan 1, 1994

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By Robert B. Parsons

"The junior mining company's bank account is depleted, but there are high hopes for the company's property. Where to get the necessary development funds is a common problem facing many juniors.This month, Tax Notes discusses briefly the principal income tax implications of several alternative development plans that are typically available to the junior mining company and its shareholders.IntroductionAt some point in time, many junior exploration companies face a common dilemma-a promising prospect has been proven up and is read y for further development, but alas, the company is flat broke! In this situation, a number of alternatives is available to the company, including the possibility of ""going it alone"" by raising capital through a public offering, or by striking a deal with a ""major"" or some other substantial investor.This article focuses on the latter possibility, and discusses in broad term s the main income tax implications of various arrangements between a typical junior exploration company and a larger public company for the development of a particular property. It will be appreciated that a discussion of other important considerations, such as those pertaining to securities exchange regulation s and company law requirements, is beyond the scope of this article.Jointly Owned CorporationPerhaps the simplest way of dealing with the problem of financing the development of a property is to sell the property outright, pocket the proceeds, and run! Clearly, though, this alternative is unacceptable to most prospectors and developers, who are predictably reluctant to completely relinquish their equity interest in a promising property. An additional strike against such an outright sale is that the sale could trigger an income tax liability. Generally speaking, in the case of a simple sale of a mineral property, for income tax purposes the proceeds are applied to reduce the taxpayer' s unclaimed balance of Canadian development expense (""CDE""), with any unapplied excess being brought into income and taxed at ordinary corporate tax rates."

Jan 1, 1983

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By H. R. Kempthorne

"The Property of Bevcon Mines Limited, including a recently acquired adjoining south group, occupies an area of 2,625 acres in northeast Louvicourt township, Abitibi county, Quebec. It is situated 17 miles east of Val d'Or at the junction of provincial highways 58 and 59.Gold was first discovered in the area in 1931 by the late S. B. Jowsey on the present property of Buffaddison Gold Mines adjoining to the west. However, it was not until the winter of 1944-45 that diamond drilling encountered encouraging results on the Bevcon claims. During the period 1946-1948 a shaft was sunk to 1,000 feet and considerable development undertaken from the 500-foot to the 1,000-foot levels. Between 1947 and 1950 approximately 24,000 tons of dump ore and 48,000 tons of ore by stoping were milled at Perron Gold Mines. The favourable results of these tests prompted the decision to construct a milling plant at Bevcon. The mill began operating in July 1952, and presently has a capacity of 800 tons per day. In 1953 the shaft was deepened to 1,600 feet and is currently (1955) being driven to 2,225 feet.Total production of gold to the end of 1954 has been 101,024 ounces from the milling of 697,427 tons of ore of an average grade of 0·163 ounces per ton.GeologyThe Bevcon orebodies occur in a granodiorite stock which has an east-west length of approximately 4 miles and a maximum width of 1 1/2 miles. The property covers the central portion of the stock and its contacts with the Keewatin volcanics. Approximately one-third of the northern contact and one-half of the southern contact are contained within the Bevcon claims. The granodiorite has been cut by acid (feldspar porphyry) and basic dykes trending east-west. A younger diabase dyke, 300 feet wide, strikes northeasterly across the property 1,000 feet east of the shaft.The main ore zone, striking east-west, lies between the more northerly porphyry dyke and the north granodiorite-greenstone contact. It has been extensively sheared, fractured, altered, and mineralized by gold-bearing solutions. It is approximately 2,000 feet Jong from the west boundary towards the diabase dyke. The shaft is centrally located and passes through the south contact of the ore zone at the 500-foot level. The zone increases in width and trends northerly with depth, due to the porphyry and greenstone contacts having average dips of 80 degrees and 70 degrees respectively to the north. Thus on the uppermost or 500-foot level the width is 150 to 200 feet, and at the present bottom level at 1,600 feet the width is 400 to 500 feet.Another gold-bearing zone has been indicated 200 to 400 feet south of the main ore zone by limited surface drilling."

Jan 1, 1949

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005

By G. B. Bosworth, M. J. Lake, J. W. Hogg

The Quintette Coal operation in northeastern British Columbia has one of the world's largest Preparation Plants, with a design capacity of 6.5 million tonnes per year of clean coal.This paper will discuss several innovative aspects of the flowsheet and plant design with particular reference to the selection of process equipment, materials handling and control systems.The operations and maintenance experience during the first two years of production will be described and discussed in relation to the design objectives.

Jan 1, 1987

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By P. E. Mather, M. J. M. Krane

Uncertainty quantification is a means of articulating the reliability of model estimations. Models of copper pyrometallurgical processes have been published for decades but discussion of their reliability has typically been terse and qualitative, mitigating understanding of their exact applicability to industrial situations. This presentation shows basic uncertainty propagation and Bayesian model calibration, two powerful uncertainty quantification tools, applied to a reduced order model of copper fire/anode refining. The implications of the uncertainty quantification analyses on the applicability of the model results to industrial practice are then discussed. Finally, other possible applications of uncertainty quantification to copper extractive metallurgy are explored. INTRODUCTION Modern copper production operations, including mining operations through wire drawing factories, are ubiquitously heavily instrumented. Most mine-sites and smelters have large repositories of historical data. That said, much of this data is not exploited to its maximum effect. This proceeding provides examples of using uncertainty quantification (UQ) to maximize the informational yield of the data collected from a fire-refining operation. Anode/Fire Refining is the final pyrometallurgical step in the production of copper anodes; it is an essential and universally employed processing step at smelters (Schlesinger, King, Sole, & Davenport, 2011). Much like the smelting and converting furnaces further up the process stream, anode furnaces are difficult to instrument due to their high temperature and the corrosive and/or caking quality of their offgas. This makes continuous and accurate measurement of the streams leaving the unit operation, e.g. liquid copper, slag, and offgas very difficult. As an example, offgas flowmeters, while providing continuous draft values, could miss the actual draft value by tens of percent due to caking or corrosion. UQ methods account for the uncertainty in process measurements and parameter values; they use a process model with measurements of performance indices to provide better and better estimations of process performance. This proceeding will first introduce a surrogate model for copper fire refining, made from a 1D, transient, reacting flow model of the process presented elsewhere in these proceedings (Mather & Krane, 2019). Discussion of the data used to make the surrogate model, as well as the creation of the surrogate model, will be included. Then, a Monte Carlo simulation will be performed, showing the expected soot production rate based on the surrogate model and assumptions about the uncertainty in the model’s parameters. Finally, the surrogate model parameters will be calibrated in a Bayesian way; this will tell what the actual uncertainty in the parameters are, given a set of observed industrial data and prior assumptions of the observations’ and parameters’ uncertainty.

Jan 1, 2019