Search Documents

By Z. M. Zavodni, C. D. Broadbent

"Major rock slides in open-pit mines are rare, but they can develop in spite of sophisticated slope engineering design practice. Experience has shown that, except under high seismic load conditions, the serious slope instability condition is almost always accompanied by the gradual development of one or more tension cracks behind the slope crest, allowing for time-displacement monitoring. Continuous surface displacement measurements with attendant prompt analyses are usually adequate for the prediction of slope behaviour.This paper describes efforts that have been made to quantify parameters associated with slide movement, and compares the displacement records of several large-scale open-pit porphyry copper mine slope failures. Two principal failure stages are recognized in the typical slope failure leading to total collapse: (a) REGRESSIVE STAGE, during which the failure will re-stabilize if some disturbance external to the rock and structure is removed; and (b) PROGRESSIVE STAGE. during which the failure will gradually displace at an accelerating rate to the point of total collapse unless active control measures are taken. Over-all displacement records in both failure stages are apparently of simple exponential form. with a definite break occurring at the onset-of-failure point.Certain common empirical relationships are suggested for the large-scale slope failures analyzed in this study. Based on plots of displacement rate vs time prior to collapse, a semi quantitative empirical relationship is presented for failure collapse prediction. The comparison of historical slide displacement records furnishes the operating engineer with practical guidelines to estimate the characteristics of future large-scale slope failures."

Jan 1, 1980

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By Si Qin

Unknown goafs and roadways of abandoned coalmines can be a great water inrush hazard for coalmine workers. Consequently, advance detection of such hazards is of great importance. By detonating seismic charges in underground coal seams, we can collect seismic data using a surface survey line, which is located across the ground projection of the underground shot point. This experiment was conducted in a coalmine in Shaanxi Province, China. After surface elevation compensation and travel time adjustments, we accurately determined the position of the goaf boundary along the survey line based on the wave velocity anomaly on the seismic record. Then we used a scattered wave imaging technique to enhance the energy of the scattered waves that are generated when the coal seam roof slide wave (refracted wave when the incident angle bigger than the critical angle) hits the roadway, thus confirming location of a geological discontinuity (roadway). This experiment shows that the coalmine ground seismic method, employing an underground explosive charge and a surface seismic array, has the ability to detect an abandoned roadway and goaf in advance of coal mining, thus can improve worker safety.

Aug 1, 2013

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006

By W. E. Cockfield

"The Last Chance claim is about 13 miles north of the village of Nicola and northeast of the city of Merritt; in the south-central part of British Columbia. It lies within Nicola mining division on the northern slope of Swakum mountain; near its summit. It may be reached by means of a branch road from the Kamloops-Merritt highway that leaves the highway at Nicola.The property was originally staked as a copper prospect by Oscar Schmidt in 1916. A number of cuts were driven and a test shipment of 22 tons of ore, averaging 4.6 per cent copper, was made from the surface showings. The property was then optioned to Granby Consolidated Mining, Smelting and Power Company, Limited, who did a small amount of drilling, after which the option was abandoned. The same year an option was secured by Northwestern Mines, Limited, of Spokane, and a SO-foot shaft was sunk. This option also was abandoned and after a number of years the property lapsed, but was re-staked in 1942 as a tungsten prospect along with other claims, and was drilled for the Metals Controller in 1943."

Jan 1, 1954

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By T. Shariff

Titanium alloys have found increasingly wide range of applications in aerospace, chemical, medical, sporting, power generation, oil and gas extraction industries mainly due to the low density, high mechanical property characteristics, biocompatibility, and excellent corrosion resistance. In the manufacturing routes of their finished products, welding has been a key technique used and always been a main concern requiring the stringent compliance to the well defined process. Conventionally, gas tungstenarc (TIG), gas metal-arc (MG), plasma arc, and electron beam welding processes have been used to weld titanium alloys. Nowadays, laser beam welding has provided great challenging applications for titanium alloys due to the low and precise heat input, deep and narrow fusion zone, small heataffected zone, low thermal distortion and high productivity. At the NRC Institute for Aerospace Research, some R&D work has been undertaken for titanium alloys using laser beam welding process. These investigations have mainly concentrated on optimizing the welding process as well as understanding the fundamental process-structure-property relationships. In this invited keynote presentation, the research progresses obtained and the main issues encountered in laser welding of titanium alloys will be briefly summarized.

Jan 1, 2011

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By H. Kuboyama

The synergistic effects of polymer additives such as gelatin and polyethylene glycol) (PEG) and Cl- on Cu electrodeposition have been investigated by measuring the polarization curves for Cu deposition, by rotating ring-disk electrode technique and by AC impedance measurements. The cathode potential for Cu deposition was greatly polarized in solutions containing both Cl- and gelatin or PEG, showing evident synergistic effect of polymer additives and Cl- on Cu deposition. The cathode potential was shifted to the less noble direction with increasing the concentration of Cl- in solutions containing polymer additives and showed the maximum polarization at Cl- concentration range between 0.1 and 1 mmol/L. The rotating ring-disk electrode technique revealed that Cu deposition in solutions containing small amounts of Cl- proceeded with initial formation of adsorbed intermediate CuClad. The Cole-Cole plots obtained by AC impedance techniques suggest that the reduction of CuClad is suppressed by polymer additives. The morphology of Cu deposited from solutions containing both PEG and Cl- showed the compacted surface composed of smaller grains due to an increase in the overpotential for Cu deposition.

Jan 1, 2007

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase.

Aug 1, 2013

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By T. Macpherson

Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980