Search Documents

By Mohammadreza Jalali

Alberta contains over 400 billion barrels of viscous crude oil in fractured carbonates but there is no viable extraction technology as yet. Petroleum geomechanics has become a vital part of the assessment of such hydrocarbon reserves, especially for naturally fractured cases, which are particularly challenging in terms of accurate recovery prediction because of joint fabric complexity and lithological heterogeneity. As a result of interconnected fractures, transport properties of fractures (mostly permeability issues rather than thermal effects) are affected by production and injection activities that change the pore pressures, temperatures, saturations, and effective stresses. Enhanced oil recovery methods involving massive amounts of fluid injection (hot or cold) at high pressure (pinj) may be used to mobilize and produce the oil; therefore, deeper understanding of the fractured systems is desirable. Pressure and temperature variations in a fractured reservoir change the in situ stresses in the reservoir and surrounding rocks; this affects fracture apertures, radically changing the bulk flow properties because flux rate is highly sensitive to aperture. Hence, coupled pressure, temperature and effective stress changes must be considered for fractured reservoirs under a thermo-hydro-mechanical (THM) coupling approach.A hybrid FDM/DDM coupled method is presented to couple pore pressure and stress around a fracture in an impermeable matrix block. Deformation and stresses are calculated in each time step and then fracture permeability, which is the most sensitive petrophysical parameter in fractured reservoirs, is updated based on the fracture aperture variation. This model is then verified with UDEC (Universal Distinct Element Code) which uses a discrete approach to cope with fractured rock mass behavior.

Jun 1, 2012

By David L. Anderson

"The objective of this paper is to describe the potential impact of inter-provincial competition f or new output capacity on the Canadian potash industry. It will be shown that the ramifications of such actions are potentially severe, especially since the potash industry is one of the few non-fuel minerals in which Canada purportedly possesses a significant degree of market power. More specifically, the paper addresses the impact of possible expansions in New Brunswick, Manitoba and, perhaps, Saskatchewan. The findings suggest that such initiatives could result in substantial excess capacity and the dissipation of monopoly rents. In summary, given the market structure of the industry, it is unlikely that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation.IntroductionThe objective of this paper is to discuss the potential impact of inter-provincial competition for new output capacity on the Canadian potash industry. The ramifications of such competition are potentially severe: given that the potash industry is one of the few non-fuel minerals in which we purportedly possess a significant degree of market power(1), it is important that sound supply management practices are followed. However, possible initiatives by New Brunswick, Manitoba and, perhaps, Saskatchewan may initiate an inter-provincial competition which could result in substantial excess capacity and the dissipation of economic rents(2). Given the market structure of the industry, it is not intuitively obvious that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation."

Jan 1, 1985

By Sarah Bélair, Denis Beltrami, Deka Moussa Ragueh, Valérie Weigel

"Scandium is a highly valuable element belonging to the rare earth elements (REE) but it has different chemical and physical properties from those of lanthanides. This metal is generally used in aluminum-scandium alloys and in fuel cells but the development of its market is slowed down by its high price (more than 1000 US$/kg for a 99.0% grade product). Indeed, the low scandium content in the continental crust (an average of 22 ppm) and the difficulties to extract it selectively from solutions containing high impurity concentrations increase the cost of the recovery processes. Nowadays, scandium is primarily recovered as a byproduct.ERAMET is developing a hydrometallurgical process in Gabon (Mabounié) in which the scandium content in the deposit reaches 10 to 100 ppm. The Maboumine project consists in the extraction and purification of uranium, niobium, tantalum and REE from Mabounié ore. In the frame of this hydrometallurgical project, ERAMET had also studied the feasibility to recover scandium as a byproduct. During the ore leaching, uranium and rare earth elements including scandium are solubilized into the pregnant leach solution (PLS). Among the various methods investigated to recover scandium from the PLS, liquid-liquid extraction using Primene JM-T as extractant was chosen and tested first at laboratory scale and then at pilot scale. Selective stripping of the loaded organic was carried out by using phosphoric acid solution, allowing the selective recovery of scandium from thorium and zirconium partially extracted from the PLS by Primene JM-T under the process conditions."

Jan 1, 2016

By O. Moselhi

This paper describes a method for selection of most suitable project delivery systems for capital projects. It expands upon the method advanced by the Construction Industry Institute (CII) in 2003, and incorporates additional decision criteria and project delivery systems in a multi-tier decision computational platform. The paper integrates the analytical hierarchy process to alleviate the inherent subjectivity associated with the assignments of relative weights to selection criteria used in the CII method. It also expands the range of project delivery options to include Public Private Partnership (PPP) and Integrated Project Delivery (IDP). The range of selection criteria was expanded by 60, beyond the 20 criteria of the CII method. Relative effectiveness values are proposed for the added project delivery systems making use of recent project cases in Canada and the USA. The method was implemented in a spreadsheet application. Multiple scenarios were considered for one of the cases presented in the CII study and a sensitivity analysis performed based on the developments made in this paper. The differences in outputs between the CII method and the proposed method are discussed. This is the first decision framework that incorporates both the presently used PPP and the recently introduced IDP, along with the widely used project delivery systems. The developed method allows users to filter out the factors and alternatives that do not apply to the case at hand, based on key inputs at the upper tier. The method is flexible and can easily be expanded upon and customized by the user.

Aug 1, 2013

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By D. H. Whiting, A. J. Sinclair

"The San Antonio gold mine, in the Archean Rice Lake Greenstone Belt, was in continuous production from 1932 to 1968, during which period the mine yielded 1.35 million ounces (41 985 kg) of gold and 195,000 ounces (6065 kg) of silver from 4.88 million tons (4.44 Mt) of ore for average grades of 0.28 ounces per ton (9.0 g/t) gold and 0.04 ounces per ton (1.3 g/t) silver. After the 1968 closure, several publications appeared implying that gold grade of ore decreased with increasing depth.Recent observations by the authors show that the relatively low grades in the middle levels of the mine are controlled geologically. However, the reduced average are grade in the lower levels of the mine was due to inadequate mining control that led to a high level of dilution. The similarity of geological factors such as vein styles within structural domains, variations in mining control, recent ore muck sampling results and lithogeo chemical profiles all indicate the similarity of ore in both upper and lower levels.Strict mining control should yield improved grades of gold for future production from the lower levels at San Antonio, in contrast with the production grades of the late 19605that represented extensively diluted ore. High-quality production records are an essential component in re-evaluating a past producer, particularly where workings are accessible. Poorly founded conclusions which cannot be checked by access to workings can have a negative impact on the evaluation procedure."

Jan 1, 1990

By H. K. Fredrickson

"Midwest Joint Venture (MJV) owns a high-grade uranium deposit in northern Saskatchewan. The deposit is located too deep below surface to be mined economically by open pit methods, and as a consequence, present plans are that it will be mined by underground methods. High-grade uranium ore of the type at MJV, encased in weak, highly altered ground and with radon-rich water inflows, has not before been mined by underground methods.The test mining phase of the project, completed in 1989, had three objectives: 1. to evaluate radiation protection requirements associated with the handling of large quantities of radon-rich water and mining highgrade uranium ore in an underground environment; 2. to investigate the quantity and quality of water inflows into the mine; and 3. to investigate ground conditions in and around the ore zone as an aid in determining the production mining method to be used.With information gained from the test mining project, a mining method for the production mine has been devised. Level plans have been drawn up, ventilation system designed, pumping arrangements made and methods of ore handling considered. All this is to be done in a manner that will be safe for those doing the work underground. Some of the mining methods planned are felt to be unique in that they are designed to cope with mining problems not known to have been encountered before. New problems underground have required new methods to handle them. Remote drilling, blasting, mucking and backfilling form the basis of the planned mining method."

Jan 1, 1992

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size."

Jan 1, 2016

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By A. G. Roach

IT IS generally stated that the gold ores of Nova Scotia are free-milling, and for the most part this is true. However, there is a certain proportion of the gold finely disseminated throughout the sulphides, notably arsenopyrite, and this gold is definitely not recoverable as 'free-milling' gold by amalgamation. The proportion of free-milling gold to total gold seems to vary widely in different localities in the Province and is lowest in deposits of the fissure-vein type. The problem of recovery of these relatively recalcitrant values is usually one of economics, in some plac.es a simple gravity concentrate being of such low tenor that its extraction and subsequent disposal will not bear the costs involved. In other cases, such a high percentage of values escapes from the mortars and plates that concentration is definitely indicated. The size of the mining operation is also an important factor. In the large majority of cases, however, some concentrating step is warranted, even if the resulting concentrate is stock-piled until sufficient has accumulated to justify further treatment.

Jan 1, 1940

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By D. G. Brophey, J. A. O’Neill

"High costs, both in terms of human resources and financial costs, have long been the end result of accidents involving vehicles which continue to occur too often throughout our industry.For example, radio remote control LHDs too often seriously injure their operators in underground operations. Costly efforts are required by mine owners to provide safety bays and platforms from which their operators can work safely. In open pit operations, large heavy haulers have too frequently backed over vehicles or turned into vehicles unfortunate enough to be situated in their large blind spots. These are just two examples of situations that have occurred again and again under similar circumstances.Meanwhile, electronic methods of detecting proximity to vehicles have continued to develop. The time has come for the industry to think “outside the box” to evaluate whether many of these new methods can solve these recurring problems.This note takes a look at various types of proximity detection technologies that are in use today in other industries, and discusses the various potential applications within our industry."

Jan 1, 1998

By N. W. Martison, J. E. Hawley

"The Moulton Hill deposit is in the Eastern Townships of Quebec, 3 miles northeast of Sherbrooke. It is complex, both structurally and mineralogically, consisting of a narrow, irregular, mineralized zone that has been traced for a length of 600 feet, and in places to a depth of 1,000 feet, containing copper, lead, and zinc sulphides with a low content of gold and silver. It lies in a series of highly schistose micaceous rocks, believed to be of Ordovician age, but the mineralization is probably post-Lower Devonian. New details of the structure of the ore have become available since it was first described (1) , and as these show some striking peculiarities a further discussion is here merited .As detailed elsewhere, the deposit was discovered in 1942 as a result of regional geological studies followed by the application of electrical geophysical methods.Actual production began in July, 1944, and ceased in June, 1945. During the period July, 1944 to June, 1945, 75,643 tons were milled§, yielding the following:"

Jan 1, 1954

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986