Search Documents

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By Raphaël Mermillod-Blondin, Claude Bazin

"Sampling is an important step for ore body evaluation and daily plant material balances. The Gy’s equation is regularly used to assess the size of the samples to be collected and to estimate the reproducibility of the collected samples. The equation works well for iron and base metal ores but seems to produce pessimistic estimates of the gold content reproducibility for gold ores. A model is proposed to simulate the division of samples using a standard splitter and discrepancies are observed between the Gy’s equation predictions and simulated samples reproducibility for crushed gold ore. Results of the simulation show that sampling a pile of ore crushed to -2 mm should lead to more reproducible gold content than it is observed in practice and predicted by the Gy’s equation.INTRODUCTION With current gold prices above $1400 per troy ounce operators seek for new economical ore bodies. The metallurgical evaluation of an ore body is one of the numerous steps required to justify the investment for the development of a gold mine. Metallurgical testing requires to sample the ore body and to prepare the ore sample for the grinding and separation tests. The preparation implies crushing the ore usually to less than 2mm and its division into batches of a given weight for subsequent processing. For gold ore testing a batch of crushed ore is ground in a laboratory mill and leached using cyanide. Gold recovered in the solution is used as an indicator of the ore processing amenability. One difficulty associated with ore testing is due to the reproducibility of gold content measurements of the feed sample. According to the Gy’s equation (Gy, 1979; Morisson, 2009) the division of a 20 kg batch of -2 mm ore containing 5 g/t of gold into batches of 1 kg may lead to batches containing 5 ± 5 g/t of gold. For this reason the gold content of a feed sample is usually back calculated from the assays of the solution and solids residues of the leaching process. However, these two assays may contain measurement errors that can propagate through the calculation of the gold recovery. The use of the feed assays as a redundant information could add robustness in the evaluation of ore amenability to processing. This paper discusses the problem of sampling reproducibility for a gold ore. The analysis is carried out with reference to the Gy’s equation for the sampling of particular materials."

Jan 1, 2012

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By F. Dai

Granitic rocks usually exhibit strongly anisotropy due to pre-existing microcracks induced by geologic loadings. The understanding of the rock anisotropy in mechanical properties such as tensile strength is critical to quarrying and stabilization of underground structures. In this paper, Brazilian tests are conducted in combination with MTS material testing machine and split Hopkinson pressure bar (SHPB) system to measure both static and dynamic tensile strength of anisotropic Barre granite. Samples are cored and labeled using the three principle anisotropic directions of Barre granite (BG). These directions are also chosen as the loading directions for the Brazilian discs. For dynamic tests, pulse shaping technique is used to achieve dynamic equilibrium in the samples during the test. Finite Element Method is implemented to formulate equations that relate the failure load to the material tensile strength employing a orthotropic model for Barre granite. For samples in the same orientation group, the tensile strength shows clear loading rate sensitivity. The tensile strengths exhibit clear anisotropy under static loading; while less anisotropy under dynamic loading. The tensile strength anisotropy of Barre granite is interpreted as interactions of the pre-existing microcracks.

May 1, 2009

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By D. J. McLaws

"Recent innovations in metal smelting technology utilize continuous oxygen-enriched smelting and converting processes which are capable of producing off-gases containing up to 60% SO2 or more. Other SO2 recovery processes, involving solvent absorption and steam or vacuum regeneration, can produce off-gases with SO2 concentrations nearing 100%.Processing of these high-concentration SO2 off-gases in conventional sulfuric acid plants can cause excessively high catalyst bed temperatures and poor SO2 conversion. In order to avoid these problems, a conventional acid plant design must dilute these high SO2 process gasses with dilution air in order to provide the required oxygen to effectively convert the SO2 and provide a heat sink (via the inert N2) such that the exothermic reaction, SO2 + ½ O2 ???SO3, does not exceed the temperature limit of the catalyst or the converter vessel.MECS, Inc. (MECS) has proven that a high SO2 feed gas design can be a viable option which can increase energy recovery, reduce energy consumption and potentially reduce capital costs."

Jan 1, 2014

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By Michael Young, Peter Allum, Mingwei Gao

"Tough economical conditions and high grade but fine-grained ore processing have forced the mining industry to look for more efficient processes. Isa Mill Technology for ultra-fine and fine grinding is one such process employed at several mining operations in Australia including Mount Isa Mines Limited in Australia. Mount Isa Mines is a business unit of MIM Holdings Limited. MIM is an Australian-based international mining and mineral processing company with around 8000 employees worldwide. Major products include copper, gold, zinc-lead-silver, coal and technology sales.The Isa Mill is a horizontal stirred mill with sizes up to 3 m3 chamber net volume and 1 120 kW installed motor. It was jointly invented by Mount Isa Mines of Australia and Netzsch Feinmahltecknik GmbH of Germany for ultra-fine and fine grinding duties in the minerals industry. Isa Mill operations started in 1994 at the Mount Isa Mines Leadzinc Concentrator and then at MIM’s McArthur River Mine in 1995. These Isa Mills have been used to liberate sphalerite and galena at Mount Isa and silica at McArthur River by grinding to less than 7 micron.This paper discusses the Isa Mill Technology and reports on the metallurgical performance of the Isa Mills at Mount Isa Mines, including work done over the last 9 years to improve mill design, process efficiency and maintenance, which has resulted in the current state-of-the-art Isa Mill Technology.INTRODUCTIONThe current leadzinc deposits at Mount Isa Mines (George Fisher, Hilton and Isa) have an average grade of 10.5% zinc, 7.2% lead and 165g/t silver. Fine grinding, in particular in the zinc retreatment circuit requiring a milled product P80 of 7 micron, is essential to treat the ores from the Mount Isa Mines deposits. Every one micron size reduction in the zinc retreatment circuit below a P80 of 10 micron improves the overall plant zinc recovery by 1%, resulting in an increase in revenue of about 1 million dollars per annum."

Jan 1, 2002

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By R. Samuels, R. Klimpel

"IntroductionLaboratory and industrial grinding tests have shown that the process of size reduction of metal containing ores can be significantly influenced by chemicals added to the slurry being ground.,The terms grinding aid or grinding additive refer to a substance which, when mixed into the mill contents, causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use.A wide variety of grinding additive mechanisms have been suggested in the general mining literature (1,2,3,4,5,6,7). The prevention of particle agglomeration, slurry cushioning of grinding media impact, grinding media coating, changing the strength of macro porous rocks, and chemical adsorption on flaw surfaces to change bonding forces and surface energy have all been suggested. More recently, some grinding additive work has been carried out (8,9,10,11) which suggests that the use of efficient chemicals to control the fluidity of dense slurries is a viable economic approach to achieve improved grinding rates. These increased grinding rates are achieved with no increase in power to the grinding mills and apparently with no increase in media consumption costs. Unlike much of the previous work with grinding additives, this recent work is accompanied by a rather complete engineering characterization and prediction of performance capability. The chemicals involved were chosen so as to efficiently control the viscosities of slurries under conditions of high shear yet not adversely affecting flotation, flocculation, and other downstream surface chemistry operations."

Jan 1, 1979

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004