Search Documents

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By E. P. Evoy, A. W. Jolliffe

"The Uranium deposit of Gunnar Mines, Limited, is on the south shore of Crackingstone peninsula in the Beaverlodge area of northern Saskatchewan.The ore consists of disseminated pitchblende and uranophane in brecciated syenite, and forms a tubular or pipelike body, outcropping at the surface and plunging southward at about 45 degrees for a known length of1,400 feet (see Figure I). The upper portion is being removed by open-pit mining to a depth of 300 feet below adjacent Lake Athabasca. The remainder will require underground mining methods (see Figure 2).The property was staked in July, I 952, and the orebody was subsequently defined by about 70,000 feet of diamond drilling. A 1,250-ton mill was completed in 1955, and production commenced in September of that year with ore from the open-pit operation. The mill is presently being increased to 1,650 tons capacity, and a three-compartment vertical shaft is being sunk to 1,250 feet in preparation for underground mining.GeologyThe mine property is underlain by an assemblage of Precambrian metasediments known locally as paragneiss, granite-gneiss, and syenite. These lie on the southeast limb of a southwest-plunging anticline, strike about north 75 degrees east, and dip southward at about 45 degrees. Para- gneiss outcrops in the northwestern half of the claim group, and again on the islands south of St. Mary's Channel. The granite-gneiss lies conform-ably within the paragneiss and makes up the southeastern part of the property. The syenite forms an irregular, triangular-shaped mass within, and near the footwall of, the granite-gneiss band. Small lenticular bodies of mafic rocks are also present, the former being most prevalent in the paragneiss.The granite-gneiss is coarse to medium-grained, pink to grey, well foliated, and composed of feldspar (65 per cent), quartz (20 per cent), chlorite, and minor mica. The general concordance of its contacts with paragneiss and the absence of intrusive relationships along these, the presence of uniformly oriented inclusions of obviously sedimentary origin within the granite-gneiss, and the variation in colour and texture across the strike all strongly suggest that this member represents a granitized sedimentary rock."

Jan 1, 1949

By Robert B. Parsons

"Although the April 19, 1983 federal budget appears to put greater emphasis on new or expanded government spending programs in an effort to get Canadians working again, the budget proposals contain a light sprinkling of tax changes which could be of some direct benefit to the mining industry.This month, Tax Notes examines some of the more important of these changes.IntroductionSome sectors of Canada's mining industry could benefit from the proposed income tax changes announced by Finance Minister Lalonde in delivering his budget address to the House of Commons on April 19, 1983. Improved depletion allowance rules, expanded investment tax credits, better use of business losses, and inflation proofing of personal capital gains on Canadian common shares are all part of the measures included in Mr. Lalonde's first budget to try to reinvigorate the battered Canadian economy.Improved DepletionUnder the Income Tax Regulations, a taxpayer who incurs Canadian exploration expense (and certain other eligible expenses) is permitted to deduct not only the full amount of the Canadian exploration expense (""CEE""), but also an additional allowance (the so-called earned depletion allowance) equal to one-third of the CEE. Thus, a taxpayer in certain circumstances can claim a deduction of $1.33 for each $1.00 of eligible expenditure, including CEE.Although CEE can be deducted from any source of the taxpayer's income (for example, from investment income, salary income, and so on), prior to budget date the earned depletion allowance was deductible only from the taxpayer's resource profits. This restriction on the deductibility of the earned depletion allowance substantially reduced the attraction of the allowance: few individual investors or investment companies, for example, have the required stream of resource profits, at least when the CEE or other eligible expenditure is made."

Jan 1, 1983

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By P. Belley

Prior to 2006, the filtration unit for leached sludge treatment (filter press) permitted the filtration, washing and drying of cake to 17% (w/w) moisture. That year saw moisture content abruptly increase to 20% (w/w), drastically changing the rheological properties of the cake. The cake became sticky and agglomerated. This led to major disruptions of operations and plant capacity (cake release and cake conveyor problems, complicating the subsequent steps of the process). The conditions for the filtration, washing and drying, were simulated to ease cake unloading without aggravating dust emissions (moisture about 17% (w/w)). All of the laboratory tests yielded a moisture content above 17% (w/w). Therefore, we concluded that the moisture problems were not due to a recipe change in primary material, but to an operational problem in the filter press. Through the laboratory results, the filter press operating conditions (washing ratio, drying pressure and drying time) were optimized to enable a reduction in cake moisture to 17% (w/w).

Jan 1, 2007

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

Economics of corrosion, the corrosion modes and causes, corrosion control methods to combat corrosion, along with a summary of issues and their implementation in the aerospace industry are briefly discussed.

Jan 1, 2004

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By Don Lemmen

Impacts, Adaptation and Vulnerability ? regional climate changes (temperature and extreme events) have already affected many physical and biological systems ? natural systems are vulnerable to climate change, some will be irreversibly damaged ? many human systems are sensitive to climate change ? Projected changes in climate extremes could have major consequences

Nov 1, 2002

By L. Kraszewski

"IntroductionPortland cement is produced by burning an accurately proportioned mixture (raw feed) of finely ground limestone, silica, alumina, and iron oxide. The kiln discharge (clinker) is a chemically complex mixture of calcium silicates, aluminates and ferrites which when ground and blended with from 2 to 5 percent of calcium sulphate is sold as Portland cement.ManufactureThe most common raw materials are limestone and clay or shale. The raw mix is finely ground and heated to about (2600°F) 1430°C to decompose the calcium carbonate and combine the calcium oxide with silica, alumina and iron to form a partly fused clinker. The clinker is then ground, usually with a small proportion of calcium sulphate (gypsum), which regulates set. Cements with special properties are produced by varying the oxide composition and also by adding small amounts of chemical agents at the clinker-grinding stage or later.Clinker is manufactured by either wet or dry process methods. In the wet process, raw materials are prepared, blended and fed to the kiln as a water slurry (about 30-35% water) . In the dry process, raw materials are prepared, blended and fed to the kiln as a dry powder (about 0.5% water). The processing procedure is as follows:"

Jan 1, 1982

By E. J. Wade

The general location, climatic conditions and access of the Tasu mine are covered briefly, with comments on the Jack of conventional transportation and communication facilities. The Haïda story of Tasu and early at-tempts at production are presented, together with a discussion of the government legislation which throttled exploration and production in the late fifties. General and specific details of local geology, mineralogy and current ore reserves are also covered.

Jan 1, 1968

Partnership with MiHR ? AHRC and MIHR jointly developed Mastering Aboriginal Inclusion for Mining ? Customization specific to mining Mining is unique? ? History of Aboriginal peoples and the land ? Unique community needs ? Effects of Impact Benefit Agreements ? Remoteness of mines ? 1200 Aboriginal communities located w/in 200km of active mines or exploration ? Long term effects of the land

May 1, 2009

By G. F. Warning

"THE H. B. Mine is situated on the north side of Sheep Creek valley, about six miles southeast of Salmo, B.C. It is the most northerly producer along a belt containing a number of zinc-lead deposits, including the Jersey mine of Canadian Exploration Limited, 3 miles to the south, and the Reeves MacDonald mine, 12 miles to the southwest. The important zinc-lead producing area around Metaline Falls, Washington, lies 23 miles to the south. Two prospectors, Horton and Benson, located and staked the oxidized outcrops in 1.907. The property was named the H.B. after the two discoverers. Exploration by a number of operators failed to locate any sulphide orebodies until 1946, when Cominco began a geological study followed by surface drilling which was successful in locating extensive sulphide mineralization. A program of underground exploration revealed sufficient ore to war-rant mill construction. A 1 ,000-ton mill was completed by 1953, but due to low metal prices production was deferred until May, 1955. To September 1, 1959, 1,900,000 tons of zinc-lead ore have been milled; present milling rate is about 1,250 tons per day. Concentrates are trucked to the Trail Smelter, a distance of 35 miles."

Jan 1, 1960

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By C. S. Parsons

Ore-Testing laboratories are maintained by the Mines Branch, Department of Mines, at Ottawa for the purpose of conducting experimental test and research on ore treatment. Sample shipments of a few hundred pounds to car-load lots of Canadian ores are received on application for experimental tests, and all possible methods of treatment are investigated. Reports are issued to the shipper, containing the results, with recommendations as to the most economical method of treatment. These reports have been of valuable assistance to mining companies in the preparation of plans for the design and equipment of their treatment plants. Investigations have been conducted on ores and metallurgical products from all parts of the Dominion. The ores from practically every producing mine and important mineral occurrence have been investigated in these laboratories.

Jan 1, 1931

By K. Kudo

Magnesium rods of 99.95% purity and approximately 6 mm in diameter were continuously cast at rates of between 15 and 25 mm/min by a heated mould process and their mechanical properties evaluated. It was found that rods cast at 15 and 20 mm/min consisted of a single crystal, while rods cast at a speed of 25 mm/min were multi-crystalline and showed a unidirectional structure. Although room temperature tensile ductility to fracture varied widely, it was found that with an appropriate crystal orientation, cast rods can exhibit elongation by as much as 215%.

Jan 1, 2006