Search Documents

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By Johnny Zhang, Yang Anguo, Li Weifeng, Xueyi Guo

"SKSTM oxygen bottom blowing smelting technology was developed by SKS-ENFI at SKS Smelter, Hunan in the 1990s to replace the conventional sintering process and thus to meet the high national EHS standard for lead.Since then, two major milestones have been achieved:1. Since 2002, the SKS oxygen bottom blowing smelting-blast furnace reduction has been in operation at SKS, YGL, Chizhou smelter etc. Now in China, about 50% of the lead (4.2 millions t/year) is produced using SKS process; and2. Since 2008, the blast furnace has been replaced by direct reduction of molten rich lead slag at YGJ smelter, which is more energy-efficient since no slag cooling is required. This two stage process (SKS Oxidation- Direct Reduction) is named as the YGL process.Since 2008, numerous technological innovations have been implemented in the furnace design, process control, and maintenance at YGL. The plant has been successfully demonstrated its unique excellent performances on all aspects from processing capacity, product quality, energy reduction, cost reduction and emission reduction. The purpose of this report is to update all the improvements with proven tracks.Meanwhile, a preliminary comparison on the following aspects between the YGL process and other similar technologies has been discussed:1. Plant design and operating conditions;2. Mass and heat balances, metal (Pb, Ag) recovery;3. Consumables, oxygen gun and refractory lining life;4. Energy consumption and operating costs;5. Sulfur capture and emission reduction etc.It is concluded that the modified SKSTM process is a clean SO2-free emission process. The process is characteristic of other features such as no extra fuel addition, low capital with a small foot-print design, low OPEX, high throughput, easy operation, long refractory lining life and high productivity (95%+ on line time annually). It offers an alternative cost-effective technology for lead smelting industry."

Jan 1, 2014

By A. Fawcett, B. C. Dyer

Abstract - The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.

Jan 1, 1994

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By F. Habashi

The pioneer work on pressure hydrometallurgy was conducted in Russia at the end of the nineteenth, and the beginning of the twentieth centuries, by Karl Josef Bayer (1847-1904) and Vladimir Nikolyevitch Ipatieff (1867-1952), both working independently in Saint Petersburg. Bayer was studying pressure leaching while Ipatieff was studying the precipitation of metals and their compounds by hydrogen under pressure. Gradually, industrial applications took place first in the aluminium and later in the nickel industry. Today, the technology is well established in a large number of industries, such as uranium, gold, zinc, titanium, tungsten, and more recently copper.

Jan 1, 2004

By R. Stauffer, S. Lindsay

"Sherritt Gordon Mines Limited utilizes pressure hydro-metallurgical techniques to recover nickel, copper and cobalt from su1phidic concentrates, mattes and various other metal-bearing materials.A brief description of the nickel refinery operation is given. In the nickel refinery process, an ammonia pressure leach is employed to treat the feed materials to dissolve the non-ferrous metals as their respective ammine complexes. The resulting leach solution goes through a series of steps which removes copper as copper sulphide and further purifies the solution prior to nickel precipitation by hydrogen reduction. The reduction end solution, containing the cobalt which was originally present in the leach solution as well as residual nickel, is treated with hydrogen sulphide. The resulting nickel-cobalt sulphide precipitate feeds the soluble cobaltic ammine process, which separates the nickel and cobalt and recovers the cobalt as a pure powder.A detailed description of the cobalt recovery process is given. Included are the various steps, comprising: acid leaching of the mixed sulphides, solution purification, ammine complex formation and cobaltous oxidation, two-stage nickel precipitation, cobalt conversion and reduction. A brief description of cobalt powder handling is included, along with typical physical properties and chemical analyses of the cobalt product. In general, the purpose of this paper is to describe the present plant practices employed in the recovery of cobalt as a by-product of the nickel refinery operations."

Jan 1, 1967

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By J. Gotor, C. Frias, E. Delgado

The Iberian Pyrite Belt (IPB) is one of the world's largest reserves of primary sulphides containing base metals (Cu, Zn, Pb), precious metals and some special metals such as indium. Estimated resources are over 1,500 million tonnes of volcanogenic massive sulphide ores. From 1980´s Europe lives the decline in its mines mainly motivated by the low price of the metals. One aspect that contributed equally to this was the ecological disaster produced by the discharge of more than seven million tonnes from the tailings dam of Boliden-Apirsa (Aznalcollar) in 1998. Today the situation is different; the companies present in the IPB have given evidence that it is possible to reconcile mining projects and care on the environment, and the regional authorities are opening a public tender to re-start Aznalcollar mine. A new challenging era has been started at this Spanish/Portuguese mining area. This paper presents the results and preliminary economics of a project devoted to IPB primary sulphides processing through different technology approach, e.g. conventional selective flotation against bulk flotation or mixed metals flotation combined with hydrometallurgical processing.

Jan 1, 2014

By Primak. George J.

"In the development of a new product as well as during its introduction on the market, it is very important to give due consideration to problems involving patents, licenses and trade marks. At the very beginning of the research and development program, it is obviously essential to ascertain, through a suitable patent search, that the product in question will not infringe any patents which are still in force. Then, a possibility of achieving one's own patent or proprietary position on the product or the process of its manufacture should be carefully explored. Licensing arrangements that one may reach with respect to patents and know-how covering such new product may, in the final analysis, determine its over-all success or failure. If one can count on licensing revenues or some favourable cross-licensing arrangements with respect to a newly developed product, this may go a long way to achieving profitability and success. The selection of a good trade mark is probably one of the most important acts that one has to perform once the product is developed, as customers will identify the new product by such a trade mark. In many instances, successful marketing and widespread acceptance of a product are largely due to its appealing name or trade mark, accompanied by proper promotion and advertising. Once the trade mark has been adopted, it should be registered in the Trade Marks Office to provide the protection afforded by federal statute. If the product is to be manufactured, sold or licensed in some other countries, similar considerations should be made with regard to each such country."

Jan 1, 1973

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By W. D. Sinclair

"Between 1934 and 1956, nearly 31 million grams of gold were produced in the Matachewan area from deposits on properties belonging to Young-Davidson Mines Limited and Matachewan Consolidated Mines Limited. In 1979, production from these properties was renewed by Pamour Porcupine Mines Limited.Most of the gold produced has come from relatively lowgrade deposits (3.4 gl t or less) that occur in an east-trending belt of dykes and irregular bodies of trachytic syenite. Although small by comparison, these deposits have some of the characteristics of porphyry copper-molybdenum deposits. The mineralized syenite contains up to 5 per cent disseminated pyrite and is highly fractured and cut by quartz and quartzcarbonate veinlets. Gold occurs as native gold along fractures, in quartz veinlets and as minute inclusions in pyrite. Minor chalcopyrite and trace amounts of scheelite, molybdenite and galena are also present. Mineralization was accompanied by potassic alteration, consisting mainly of potassium feldspar.Some gold was also produced from small, but higher-grade, deposits in volcanic rocks. These deposits occur near the syenite-hosted deposits and consist of quartz veins and stringers mineralized .with pyrite and gold. Minor gold is present in some low-grade, porphyry-type copper-molybdenum occurrences and, locally, in large, isolated quartz veins.Lead isotope analyses suggest that the gold deposits were formed at about 2700 Ma and were locally remobilized at approximately 2400 Ma, following the Kenoran orogeny. The deposits appear to be genetically related to felsic magmas emplaced in an epizonal environment and deposited from hydrothermal solutions relatively concentrated in S and K20."

Jan 1, 1982

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By E. G. Kearnery

Introduction It is believed that the present paper will be of some interest, not because of any outstanding features of Renabie milling practice but because Renabie is the first gold mining property in a newly explored area - in Leeson and Rennie townships, Sudbury district, Ontario - to reach the production stage. The Renabie mill was originally designed by the General Engineering Company (Canada), Limited, as a 300-ton plant and went into operation in June, 1947, treating an average of only 128 tons a day for the balance of that year. Toward the end of 1948 the capacity of the plant was expanded to 450 tons a day, and the tonnage treated was gradually increased from the 1947 figure to the point where 420 tons a day was averaged for the first nine months of 1949. Description of Ore In general, the outstanding gangue component of Renabie ore is white quartz, which comprises at least 80 per cent of its total bulk and in some sections considerably more. Virtually all the gold occurs in very finely divided state; only very rarely has free gold coarser than 325 mesh been observed. The ore has a very low sulphide content, ranging from about 0.50 to 1.00 per cent by weight. The gold occurs both free in the gangue and ? locked in sulphides, the proportion of one to the other varying considerably from one orebody to the other. Pyrite is by far the most abundant sulphide, followed by galena, which, however, appears to be entirely absent in some of the orebodies. Minor amounts of pyrrhotite, chalcopyrite, chalcocite, and sphalerite have been noted. The ore appears to be entirely free, or almost so, of minerals containing arsenic, antimony, or molybdenum, and in general it could be described as free milling. The various hindrances to extraction of the gold which have been met with are believed to be due largely to the very finely divided state of the metal and to its intimate association with the sulphides and gangue. The ore contains silver, with the gold-silver ratio about 3:1.

Jan 1, 1950