Search Documents

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By Z. X. Cui, X. D. Ma, L. Contreras, X. Jiang

The bath smelting process is one of the key techniques applied in the current copper smelting production, which includes bottom-blown and side-blown furnaces differently from the direction of gas injection. Liquid matte and slag form the bath in the smelting furnace. To better understand the fluid dynamic of the bath and further optimise the operational efficiencies in the smelting furnace, physical simulation of the bath in the horizontal cylindrical reactor was investigated. The mixing behaviour and wave motion of the bath in the bottom-blown and side-blown furnaces have been studied systematically. The mixing time is reduced with increasing gas flowrate and height of the lower layer, while it increases significantly with increasing the height of the upper layer. The wave motion in the furnaces can be suppressed with the presence of the upper layer, but the bath with a lower density generates higher wave amplitude. Overall, in comparison to bottom-blown mixing, side-blown mixing shows better mixing efficiency and lower wave amplitude. In addition, the plume eye and splash phenomena occurred in the bottom-blown furnace have also been studied. INTRODUCTION The bath smelting process is one of the principal techniques used in the current copper making industry. The bath smelting techniques have some advantages of high smelting efficiencies, low capital costs, low energy consumptions and reduced dust generations. From the direction of gas injection, the bath smelting techniques can be classified into five general types: (1) top-submerged blown, e.g. Ausmelt and Isasmelt; (2) top-suspended blown, such as Mitsubishi smelting; (3) top direct-to-copper smelting, such as Outokumpu smelting; (4) submerged side-blown, such as Noranda and Teniente smelting; (5) bottom-blown, such as Dongying Fangyuan bottom-blown copper smelting furnace (Schlesinger et al., 2002; Zhao, Cui, & Wang, 2013; Perez-Tello et al., 2018). In many metallurgical processes involving bath smelting situations, the objectives of agitation are to accelerate the bath homogenization inside the bath which makes a significant contribution to process efficiency and product quality. Extensive mixing studies have been performed for ladle refining and tundish associated to steelmaking processes through water physical models. Mixing time is the parameter used to quantify the efficiency of mixing in the liquid bath and the first empirical equation predicting mixing time was proposed by Nakanishi, Fujii and Szekely (1975). Later on, more systematic studies have been carried out on ladle mixing and researchers realized that the geometry of the vessel could also have a significant impact on mixing (Khajaviand & Barati, 2010). However, the investigations using ladles which are vertical cylindrical vessels, cannot be directly used in the study of mixing behaviour in horizontal cylindrical reactors. Understanding the fluid dynamics inside horizontal cylindrical bath smelter is useful from the industrial perspective. Recently fluid dynamics of horizontal cylindrical smelter related to copper smelting have been studied by the authors’ group (Shui et al., 2015a, 2015b, 2018a; 2018b; Xu et al., 2018, 2019).

Jan 1, 2019

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"Abstract-A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By Chenming Liu, Xiao Lin, Bo Wang, Hongbin Cao, Xingang Li

Over 2 million tons of NH3-N were discharged in China per year recently, rare earth industry contributed 7.03% of NH3-N pollutant from industrial wastewater in 2007. Wastewater containing NH3-N and heavy metals mainly produced in RE extraction saponificated with ammonia and precipitated by ammonia bicarbonate. Generally, 1 ton REO cost 0.6-1.2 ton ammonia for extraction and 1.6 ton ammonia bicarbonate for precipitation, and produce 35-100 ton wastewater. Processes, like Na-saponificated, Ca-saponificated and Non-saponificated technique, are widely studied to reduce the adverse environmental effect of RE industry, while traditional processes still have advantage in production cost, process stability and product quality. In this study, a novel process that combines distillation and air-stripping is developed. NH3-N is removed and recovered based on relative volatility difference of NH3 and H2O. Phase equilibrium, heat equilibrium are calculated to determine process parameters. Hydrodynamic performance like flow field distribution is also simulated. Then, design parameters for distillation trays or structured packing are determined based on calculations and simulations. Besides, the phase diagram of (NH4)2SO4-NH4Cl-H2O in 30°C - 100°C, the typical salts composition of nonferrous wastewater, is studied to ensure commercial plants’ continuous operation. Ammonia removal tower (ART) with different high efficient column internals is designed to fit RE wastewater treatment requirement. The novel process has been commercialized in RE industry in Jiangxi, China. The commercial project operation results show the novel process reached a nearly zero-emission with >99.5% NH3-N was removed and then recovered as ammonia. Combined the novel process, the traditional REO separation process using ammonia and ammonia bicarbonate could achieve NH3-N reuse and the effluent quality meets the discharge standards.

Jan 1, 2016

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the PLS and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. In this paper, purification of vanadium leaching solution using organophosphorus, solvating and amine extractants will be reviewed. This review will be focused on vanadium separation from iron, molybdenum and uranium which are often present in vanadium resources including primary ores, fly ashes and spent catalysts.

Jan 1, 2014

By David R. Lentz

At True Hill in southwestern New Brunswick, low-grade porphyry-style Bi-8n-Mo greisen mineralization is associated with the cupola of an epizonal granite porphyry (granite) that also exhibits three episodes of brecciation. The first episode of brecciation is an in situ, 8 m to 10 m wide transitional zone of net-veined to coarse-grained "blocky" endogranitic mesobreccia that is chloritized and greisenized and hosts weak disseminated minerali.zation. In a zone closer to the host rockgranite contact, angular fine- to coarse-grained endogranitic mesobreccia with greisenized matrix is superimposed on the earlier transitional breccia. The latest episode is fault-controlled and consists of quartz- and chalcedony-hosted sub-angular to rounded fine-grained "pebble" mesobreccias that crosscut and brecciate the other breccia types, as well as the adjacent altered metasedimentary country rocks. The first two episodes of brecciation are magmatic-hydrothermal in origin related to hydrofracturing of the granite carapace and are accompanied by greisenization and mineralization, whereas the post-mineralization, silica-hosted, "pebble" mesobreccias related to hydromagmatic, low-temperature fluid circulation and/or boiling along faults near the contact. These magrnatichydrothermal and hydromagrnatic mesobreccias are similar to those associated with W-Mo-Bi porphyry-greisen mineralization at the Mount Pleasant deposit.

Jan 1, 1994

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By Gonzalo Bernstein, David G. Meadows, German Naranjo, Edgardo Tapia

"During the last decade Antofagasta Minerals’ Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.INTRODUCTIONMinera Los Pelambres is a world class copper-molybdenum operation located in the Salamanca area in Chile, in region four, approximately 500 km north east of Santiago, the capital of Chile. In the late 1990s Antofagasta Minerals developed the Minera Los Pelambres project in Chile at an investment cost of approximately $1.3 billion USDs. The project construction was successfully led and completed by Bechtel Corporation in 1999 and within a matter of months the plant was already exceeding the nameplate capacity of 85,000 mtpd. In 2001 a pebble crushing circuit was added to raise the capacity to 114,000 mtpd. In the early part of 2003-2004, it was recognized that the hardness profile was changing with depth and that in order to maintain the plant capacity additional power would be needed in the SAG mills together with upgrading of the primary crusher. In conjunction with these changes a fifth ball mill and a second primary crusher station would also need to be installed. A further detailed engineering study and evaluation was initiated by Minera Los Pelambres. This was lead by Bechtel Corporation with major design contributions from FLSmidth and Siemens in order to establish the re-powering requirements for the SAG mills. These re-powering changes together with the inclusion of a pebble crushing circuit took the plant to up to 125,000 mtpd even with harder more competent ores. Finally in the last two years an additional grinding line has been added to take the capacity to consistently over 175,000 mtpd. The third line was installed in a record time of 256 days. A schematic of the current comminution circuit, discussed in this paper, is shown in Figure 2."

Jan 1, 2012

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By Brendan Parker, Tyron Rees, Steven Hart, Abba Manesh, Ian Mcgaffin

"In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit.This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes"

Jan 1, 2012

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By A. B. Morrow

Consulting engineers are well aware of large variations in plant operating cultures between countries, companies, and even within sites and operating crews. These operating cultures must be considered when designing Advanced Process Control (APC) applications in order to maximize utilization rates and return on investment. Designs must be driven by an understanding of the totality of unit operations. Economic factors, equipment constraints, management philosophy, maintenance department responsiveness, instrumentation reliability, operating crew skills and teamwork, and individual operator concerns are all important and must be considered during application design. A general approach to incorporating operating culture considerations into APC application design is described. A case study for an iron ore concentrator plant is presented.

Jan 1, 2014

By William D. Swank, Prabhat K. Tripathy, Tedd E. Lister, Eric S. Peterson, Delon C. Haggerd

More than half of the primary neodymium, produced directly from ores, is being used to manufacture neo magnets. Neodymium, being a critical element in supply, has attracted considerable interest worldwide to recover this metal from a variety of waste streams. From among different recycling processes, hydriding-dehydriding can prove to be highly effective in recycling discarded neo magnets present in consumer electronics. In the present study, manually removed magnets from discarded Hard Disk Drives (HDDs) were subjected to the hydriding-dehydriding process in order to evaluate the resultant products for the re-fabrication of the magnets. The paper describes the effect of experimental parameters on both the hydriding and dehydriding processes as applied to different magnet chemistries.

Jan 1, 2014

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994