Search Documents

By David J. McDougall

"IntroductionThe production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with the Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivières (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about the Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian rather than the English-Canadian milieu, but whatever the reason, the other Quebec iron work s have been generally ignored. All but one of the Quebec blast furnaces could be described as ""preindustrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day.Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence river. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces."

Jan 1, 1983

By Bertrand Quiniou, Pierre Amadieu

Ion exchange technologies and processes are proven and established technologies widely used in numerous industries including hydrometallurgy for metal separation and recovery from metal bearing solutions. They have evolved through innovation which includes the development of countercurrent multistage (or multivessel) ion-exchange contactor systems with the benefit, for industrial operations, of greatly reduced footprints and ion-exchange media inventories, as compared to more traditional fixed bed contactor systems. Information on procedures for design and sizing of countercurrent multistage ion-exchange contactor systems is not readily available since it is most often proprietary know-how. The purpose of the present work is to develop a simple and innovative approach for the sizing and modeling of industrial countercurrent multistage ion-exchange contactor systems. The suggested approach builds upon published results and upon the following observation: in an industrial setting, knowledge of how component concentration or load on a contactor output streams vary with time t within a cycle duration (0 < t < T) is generally of little interest, only knowledge of time average of such concentration or load over a cycle duration T is sought for. The presented approach will be tested against current or past performances of industrial countercurrent multistage contactors of Orano Mining operations such as SNK‑3M moving packed bed contactors in Kazakhstan and NIMCIX fluidized bed contactors in Namibia.

Jan 1, 2020

A semi-automatic device has been constructed that can be used to check the solution strength of cyanide solutions. It consists of a wheel on which a gold-foil-bearing glass slide is mounted. The wheel moves the gold foil through the solution under test and intercepts a light beam. As the gold foil is attacked by the cyanide solution its light absorption diminishes. The successive in-crease in transmitted light intensity is recorded and gives a measure of the gold dissolution rate. Curves have been obtained to show the effect of cyanide concentration and oxygen content on dissolution rates. Details are presented of the construction of the unit, and some practical operating procedures are outlined. 0 NE of the important, although often neglected, factors in the extraction of gold by cyanidation is the actual dissolving strength of the cyanide solution. This depends in a

Jan 1, 1964

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By Patricia J. Dillon

Established in 1997, Prospectors and Developers Association of Canada Mining Matters (PDACMM) is a registered charitable organization dedicated to providing Earth Science education to grade school students. Through the development and distribution of educational programs and materials, PDACMM informs students of Canada?s geology and mineral resources as well as promoting awareness of the importance of rocks, minerals, metals and the mining industry. PDACMM also co-ordinates with other charitable organizations and government agencies to provide support or to work in tandem with them and reach as many young people as possible. Although PDACMM became a charitable organization in 1997, it actually has its? roots in 1994 when the Grade 7 program Mining Matters/Une Mine de Renseignments was developed to help teachers bring geology and mining into the classroom. Over 2100 of these resource kits were distributed to teachers across Ontario during the period 1995 to 1998. This unit won national recognition when it received the prestigious Partnership Focus award from the Conference Board of Canada for ?promoting science literacy for the world of work?. Due to the phenomenal success of these kits, a Grade 4 kit entitled Deeper and Deeper/Aller au Fond Des Choses was developed in 1998 in response to the opportunity provided by the new Ontario curriculum released at that time. Over 2600 of these kits were distributed throughout Ontario and there is a substantial waiting list of teachers hoping PDACMM will be able to raise enough money for another print run.

May 1, 2002

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By A. H. Lang

"The Cordilleran region of western Canada includes most of British Columbia and the Yukon and pares of Alberta and the Northwest Territories. The western part of this region was for about 50 years the principal mineral producing area of the Dominion. It lost this distinction in 1907 when production from the mines of the Canadian Shield took the lead, but it continues to provide about 15 percent of the total Canadian production. In 1945 the total mineral production of British Columbia and the Yukon was valued at $65,302,900, of which about 80 percent was derived from metals.This paper is intended to serve as an introduction co the more derailed Cordilleran papers. Part I includes a brief synopsis of the complex geology and diverse types of mineralization in the region and Parr II collates the main structural principles exemplified in the derailed papers, and draws some conclusions regarding the application of this information to prospecting."

Jan 1, 1954

By K. S. Fraser, H. J. H. Pieterse

"A pressure oxidation plant to pretreat refractory sulphide ore at the Goldstrike plant in Nevada, was commissioned in early February 1990. The plant, with a nominal capacity of 1363 t/d, was commissioned over a one-week period and achieved design capacity and availability within ten weeks an unusually short period for a plant of this complexity.The pressure oxidation process is conducted under elevated temperature and pressure conditions, and in a corrosive environment. These conditions demand that the process and engineering design of the plant be carried out in a much more sophisticated and detailed manner than is normally required in a conventional gold plant.This paper provides an account of the process and engineering design of the Goldstrike pressure oxidation plant with special emphasis on the design of the vessels, slurry pumps, piping, valves, and control systems.BackgroundLocationThe Goldstrike property is located in Eureka County in northcentral Nevada on the Carlin geological trend. The mine is approximately 40 km northwest of the town of Carlin which is situated on Interstate Highway 80. The minesite is located 1700 m above sea level in the Tuscarora Mountains.Initial Goldstrike OperationsShallow, low-grade mineralization was discovered by diamond drilling in the Goldstrike area in the 1960s. A heap leach operation was established in the mid-I970s by the previous owners. The Post deposit was discovered in 1982. Gold production by mining and heap leaching reached I t/a (40 000 oz/a). American Barrick purchased the property in 1987 and started an aggressive program of deep drilling. This led to the discovery of the Betze and Deep Post deposits and established sufficient reserves to justify an initial 4100 t/d mill and a 5 500 000 t/a heap leach operation"

Jan 1, 1992

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase&apos;s interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By A. Warczok

The computer simulator of slag cleaning in an electric furnace is based on a set of mathematical models describing heat liberation, the rate of slag reduction and gravitational coalescence of matte and metallic copper inclusions. The simulator consists of a mass and heat balances as a frame, in which the kinetic equations of the slag reduction and phase separation are incorporated. Friendly user-screen interface allows for dynamic control of process parameters in real time together with simulation of typical operations, such as furnace charging with liquid slag, solid reverts and coke, tapping out of the slag and matte, motion of electrodes and control of the transformer. The batch, semi-continuous or continuous process can be simulated. The process parameters are displayed and continuously recorded for further analysis. The computer simulator is a powerful tool for process optimization, training of furnace operators and the design of new slag cleaning installations.

Jan 1, 2007

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By R. Vergunst, E. A. Devuyst, G. Robbins

"INTRODUCTIONThe Inca process for continuous cyanide removal from industrial wastewaters was patented in 1984 by G.J. Borbely, et.al. (1). The process requires SO2, air, lime and a copper catalyst. Both free and complexed cyanide are oxidized to cyanate in the pH range 8 to 10. Cyanide bound to iron is removed by precipitation as a ferrocyanide insoluble salt and other base metals are removed as hydroxides.The process was piloted in 1982 on barren bleed solution at Campbell Red Lake Mines Ltd., Ontario (2). Since 1982, the Inca SO2-air cyanide removal technology has been applied in twelve commercial installations. The process has significant advantages over other commercial processes in the completeness of cyanide removal and lower reagent requirements and costs.COMMERCIAL INSTALLATIONSBy the end of 1988 Inca will have applied its patented cyanide removal technology to twelve commercial operations. Three of these, namely Scottie Gold Mines, Dupont of Canada Expl. Baker mill and Carolin, all in British Columbia, Canada, have ceased cyanidation operations but SO2-air cyanide destruction results were good for all mills, particularly so for over two years for the Scottie mill.Removal of cyanide from CIL slurry tailings is applied at Equity Silver (9,500 tpd) and Inca's new 1,200 tpd mill at Inca/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3,600 tpd) and Canamax's Ketza River operation (360 tpd). Repulped tailings from Merril-Crowe flowsheets are treated at Total Erickson's Mount Skukum mill (300 tpd) and Skyline's Johnny Mountain mill (200 tpd) and barren bleed at Inco/Queenston's McBean mill (500 tpd). Lynngold's MacLellan mill (1,800 tpd) treats pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating in Kitchener, Ontario. Many of the above commercial operations were described in some detail in previous publications (3,4). Typical installations are described in this paper. A summary of operating results is given in Table 1."

Jan 1, 1989

By R. Heikkilä

The utilization of Building Information Modeling (BIM) and model based 3-D control of work machines have increased a lot in new road construction in Finland as well as in other Nordic Countries. Up today, much less attention has been paid into the development of maintenance and rehabilitation processes. As a part of a large research and development program RYM PRE Infra FIN BIM in Finland, a focused research project of the BIM with experiments in total five (5) pilot projects has been performed. A main idea of the new BIM based process has been to utilize mobile laser scanning method for initial data acquirement, the use of novel 3-D analyze and modelling methods for point cloud processing, the use of new type optimization method for the planning of geometric and structural improvements needed for the existing uneven road surfaces, and further, through the creation of 3-D machine control models apply the newest 3- D machine control systems for continuous 3-D control of practical construction work using milling machine and asphalt paver. Finally, an evaluation is made between the new process model and the traditional way of working.

Aug 1, 2013