Search Documents

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

It was determined by the authors that the water that remains in the filter cake after filtration in iron ore concentrators can contain several hundred times greater concentrations of calcium ions and other cations, due to surface chemical effects carrying the ions along with the water. Filter cake from two plants was analyzed. The water retained in samples of magnetite concentrate filter cake in Plant 1 contained 5088 ppm calcium and 5995 ppm magnesium, while the Plant 2 filter cake contained 231 ppm calcium and 119 ppm magnesium. These levels were dramatically elevated compared to the water that was removed from the concentrate by filtration for recycle to the plants (9 ppm calcium/15 ppm magnesium for Plant 1, and 11.9 ppm calcium/9.3 ppm magnesium in Plant 2). In addition to possible effects on agglomeration performance, the presence of these cations also affected the efficiency of filtration. In order to reduce the effects of these cations on filtration in Plant 2, carbon dioxide was injected into the slurry before it entered the filter press. This was found to increase filtration rates by up to 23.7%. Comparison of the results from the two plants shows that the concentrations of cations present in the filter cake will vary greatly from plant to plant, with correspondingly large variations in their effects on plant operations.

Jan 1, 2004

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By R. C. E. Bray, Peter Price

"The property of Pamour Porcupine Mines, Limited, is in the eastern Porcupine area, about 12 miles northeast of Timmins. It covers parts of lots 3-6 (inclusive), cons. 5 and 6, Whitney tp., Cochrane district, Ontario. It is an amalgamation of the old La Palme, Three Nations, and Porcupine Grande properties.The first discovery on the Pamour was made in 1911. During 1911 to 1914 a small shaft was sunk on the Three Nations vein to the 200-foot level and a 100-ton stamp mill was put in operation, but only a small production was achieved. The property remained idle from 1914 to 1923. In 1924 some diamond drilling was done along the Keewatin-Timiskaming contact with some encouraging results, but the gold mineralization encountered was too low in general at the price of gold then prevailing to warrant further · work. The increase in the price of gold revived interest in the area, and the above noted amalgamation was effected in 1934. Options were taken and successively dropped by two large mining companies. Following this, exploration both on the surface and underground was started by Quebec Gold Mining Corporation, Limited. Diamond drilling in the early part of 1933 showed considerable ore in conglomerate and greywacke to the east. In the middle of 1935 Noranda Mines, Limited, assumed control and management. A new shaft was sunk and the property was ·equipped with a mill having an initial capacity of750 tons a day. This was subsequently enlarged to 1,500 tons a day.From the commencement of milling (May 16, 1936) to the end of 1946, 5,025,545 tons of ore having an average grade of 0.1327 oz. a ton ($4.64 at $35 an oz.) have been mined and milled."

Jan 1, 1954

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By H. Aminian

Gold powders have many important industrial applications. In this paper the available processes for the preparation of gold nano and micron sized powders are described. The attention has been given to hydrometallurgy route and the recent works and achievements in controlling the powder morphology are highlighted.

Jan 1, 2011

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By K. Muehlenbachs, J. U. Stemler

"Abstract - The Boston deposit is a recently discovered Archean lode-gold deposit located approximately 700 km northeast of Yellowknife, in the southern portion of the Hope Bay volcanic belt. Primary H2O-CO2-NaCl fluid inclusions associated with gold mineralization at Boston are of low salinity (4.6 ± 1.4 eq. wt.% NaCl, n = 182) and contain pure CO2. Homogenization temperatures of liquid-phase inclusions average 270° ± 33°C (n = 141), but some fluid inclusion assemblages contain coexisting liquid- and vapor-phase inclusions that homogenize near critical conditions, suggesting phase separation. In these groups, liquid-phase inclusions homogenized at 299° ± 25°C (n = 24), and vapor-phase inclusions homogenized at 338° ± 28°C (n = 18). These temperatures overlap within error, and a median temperature of ~320°C is taken as representative of trapping conditions within the veins. An approximate pressure of 2-3 kbar was estimated from fluid inclusion isochores at this temperature. Stable isotopic compositions of carbonate minerals from the mineralized zones range from -4.7‰ to -3.1‰ in d13C, and from 11.2‰ to 12.8‰ in d18O; quartz ranges from d18O = 12.8‰ to 14.9‰; and pyrite ranges from d34S = 2.1‰ to 3.5‰. The d18OH2O, d13CCO2, and d34SH2S values of the fluid calculated from these minerals at 320°C are 6‰-9‰, -2.4‰ ± 0.6‰, and 1.5‰ ± 0.5‰, respectively, and are intermediate between metamorphic and magmatic compositions. A unique source for the fluids cannot, therefore, be constrained from these data. Petrographic and geochemical data for the Boston deposit are consistent with data from other Archean lode-gold deposits worldwide, implying that the Boston deposit formed in a similar environment and from similar types of fluids. These results suggest that the Hope Bay volcanic belt may represent a major new mesothermal gold belt in this part of Nunavut. Sommaire - Le gîte Boston a été récemment découvert à environ 700 km au nord-est de Yellowknife dans la partie sud de la ceinture volcanique de Hope Bay, il s’agit d’un gîte d’or filonien d’âge Archéen. Les inclusions fluides primaires de H2O-CO2-NaCl associées à la minéralisation aurifère du gîte Boston présentent une faible salinité (4.6 ± 1.4 eq. pds.% NaCl, n = 182) et contiennent du CO2 pur. La température d’homogénéisation des inclusions à phase liquide est en moyenne de 270° ± 33°C (n = 141), mais certains assemblages d’inclusions contiennent des phases liquides et gazeuses coexistantes qui s’homogénéisent dans des conditions quasi critiques, suggérant qu’elles résultent d’une séparation de phase. Dans ces groupes, les inclusions de phase liquide s’homogénéisent à 299° ± 25°C (n = 24) et les inclusions de phase gazeuse s’homogénéisent à 338° ± 28°C (n = 18). Ces températures se recoupent à l’intérieur des limites de l&apos;erreur de mesure, et nous considérons qu’une température médiane de ~320°C est représentative des conditions de piégeage dans ces veines. Les isochores permettent d’estimer une pression d’environ 2-3 kbar à cette température. La composition des isotopes stables des carbonates dans les zones minéralisées s’étend de -4.7‰ to -3.1‰ pour d13C et pour de 11.2‰ à 12.8‰ pour d18O; les valeurs de d18O pour le quartz varient de 12.8‰ à 14.9; et les valeurs de d34S dans la pyrite vont de 2.1‰ à 3.5‰. Les valeurs de d18OH2O, d13CCO2, et d34SH2S du fluide calculé à partir de ces minéraux à une température de 320°C est de 6-9‰, -2.4‰ ± 0.6‰, et 1.5‰ ± 0.5‰ respectivement, reflétant des conditions intermédiaires entre des compositions métamorphiques et magmatiques. Il n’est donc pas possible d’identifier une source unique pour ces fluides à partir de ces données. Les données pétrographiques et géochimiques du gîte Boston sont similaires à celles d’autres gîtes d’or filoniens ailleurs dans le monde, ce qui implique que le gîte Boston s’est formé dans un environnement similaire à partir des mêmes types de fluides. Ces résultats suggèrent que la ceinture volcanique de Hope"

Jan 1, 2006

By James E. Wennen

The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.

Jan 1, 2012

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By A. J. Stapleton

"This paper gives a brief description of the occurrence and development of the Needle Mountain mine at Gaspe Copper Mines, Limited and describes the trackless mining equipment used in this highly mechanized underground operation.Maintenance of the trackless equipment is considered in detail, with particular emphasis on scheduling and control, examination and inspection. All maintenance is carried out in an underground garage, and the facilities for maintenance and field repairs are also described. Maintenance costs are given for various units and the figures for different types of loading and haulage units are compared to support the trend toward larger units and the increasing use of rubber-tired loaders."

Jan 1, 1969

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007