Search Documents

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By J. W. Rogers, S. K. Schwartz

"The Cape Breton Development Corporation (CBDC) is a federal Crown corporation which operates two coal mines (Phalen and Prince Collieries), a coal preparation plant, a railway, a central workshop and a deep water shipping facility.The Sydney coal field consists of 11 major seams, which range from 0.8 m to over 3.7 m in thickness. Of the 2.4 billion tonnes of known coal resources in the field, approximately 550 million tonnes can be mined with present mining technology. These parameters define reserves which extend more than 8 km beneath the ocean to a depth of 1200 m. With today’s design and present high production faces, the colliery life is projected at approximately 20 years."

Jan 1, 1996

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses&apos; and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By Chantale Doucet

L?utilisation du remblai en pâte dans les exploitations en vrac est de plus en plus importante. Puisque la technologie existe pour fabriquer du remblai en pâte sans construire une usine coûteuse, il est maintenant possible d?élargir le domaine d?utilisation du remblai en pâte pour y inclure des gisements filoniens où le besoin annuel de remblai est moindre. Dans certains cas, l?utilisation du remblai en pâte pourrait permettre de réaliser d?importantes économies telles que la réduction de la dilution, la stabilité des ouvertures, la récupération d?une plus grande partie du minerai par la réduction de la taille des piliers et l?entreposage de moins de résidus à la surface. L?ampleur des économies est parfois difficile à chiffrer mais il est tout de même important d?en tenir compte lors de la décision d?utiliser du remblai en pâte puisque ce sont souvent ces économies qui seront déterminantes. Différentes méthodes d?extraction avec remblai en pâte appliquées aux mines filoniennes seront présentées. Des défis et les solutions reliés à l?utilisation du remblai en pâte à la Mine Doyon seront discutés.

Oct 1, 2001

By P. J. Bourassa

Incorporated in 1957 under the laws of the Province of Quebec, Quebec Cartier Mining Co. undertook the development of its low-grade iron ore reserves located at Lac Jeannine in the southwest extremity of the Quebec-Labrador trough. This challenge comprised the construction of a 200-mile access road, two towns, a 191-mile-long railroad from Port Cartier to Lac Jeannine, a hydro-electric generating plant on the Hart Jaune River, and mining, crushing, concentrating and ancillary facilities to support a yearly production of 8.0 million tons of iron ore concentrates at 66% Fe. In order to meet increasing market demands for iron ore concentrates concurrently with the depletion of its Lac Jeannine reserves , Quebec Cartier announced, late in 1969, the first step toward bringing into production a new iron ore deposit, known as Mount Wright, located 70 air miles northeast of Lac Jeannine and 25 miles southwest of Labrador City, Newfoundland. In September 1970, the company announced its decision to develop and bring into production its Mount Wright reserves at an annual rate of 1 8.4 million dry long tons. The scope of this project included the construction of an access road linking the mine, the new town and Labrador City, Newfoundland, the extension of the railroad by some 86 miles, the construction of an ore concentrating plant with all the ancillary facilities, the development: of the mine, the construction of a pourer transmission line and a new town adjacent to Lake Daviault. The Mount Wright story is divided into five individual papers covering: (a) the history and development of the project; (b) the mine; (c) plant control by a process computer; (d) crushing, grinding and concentrating; and (e) the townsite of Fermont.

Jan 1, 1977

By Côme Carbonneau

The ten -year case history of La Société Québécoise d&apos;Exploration Minière (SOQUEM) is reviewed under the headings of the company&apos;s raison d&apos;être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern &apos;British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada&apos;s iron production was 1.85 per cent of the world&apos;s output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada&apos;s iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By A. Jain

During sheet forming, metal experiences not only multi-axial load, it also undergoes strain path changes. For example, metal in the flange region may be drawn, may bend and unbend through a bead, before bending around a die radius, etc. Compression data were obtained from AZ31 sheet after pre-straining in compression along an orthogonal direction. The compression directions correspond to the sheet product (rolling-RD, transverse-TD, and normal-ND) directions. Three cases are examined: slip dominated deformation (ND) followed by twin dominated (RD or TD) deformation, twin dominated (RD or TD) followed by de-twinning (ND), and twin dominated (e.g. RD) followed by cross-twinning or secondary twinning (e.g. TD). Slip induced pre-straining simply hardens the material, while twin dominated pre-straining alters the texture allowing the material to either de-twin or re-twin upon changing the strain path. Polycrystal plasticity modeling has been used to predict qualitative features of the flow curves during strain path changes.

Jan 1, 2006

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981