Search Documents

Neutralisation, normally using lime, is the most widely used method for treating high flows of acid mine drainage (AMD). Lime costs can be very high however. If carbonate sources could be used to achieve pH values above six, costs could be greatly reduced. For example, use of locally quarried limestone at Mt Lyell could potentially reduce alkali costs from about $A 3.5 to $A 1 million/year. Methods for enhancing the effectiveness of limestone and magnesite for neutralising Mt Lyell and Savage River AMD respectively have been examined through a series of investigations. Small-scale testwork found that the maximum pH economically achievable with ground limestone was about five, due to slow dissolution rates and surface armouring. The problems of surface armouring were greatly reduced by the use of crushed limestone or magnesite at high pulp densities (75 per cent solids w/w), enabling pH values >6 to be achieved in a practical time frame. The use of particle sizes in the range 6 mm and finer also reduces costs by avoiding the need for grinding, and reduces the problems of solid-liquid separation and solid recycling that arise if large additions of ground carbonate are used. Pilot scale tests were carried out using tumbling drum reactors with limestone and Mt Lyell AMD and a pulsed-bed static reactor with magnesite and Savage River AMD. pH values averaging 6.2 and 6.4 were achieved with Mt Lyell and Savage River AMD respectively. Approximately 80 per cent of feed acidity was neutralised. A preliminary engineering design and cost estimate has been completed on the pulsed-bed reactor and shows that the concept is technically feasible and, if results are confirmed, economically attractive. Further pilot testing is planned.

Jan 1, 2002

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003

By J Mauk, R Ruddock

The Taharoa ironsand deposit is 1600 hectares in size and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The sand predominantly contains heavy mineral-rich sediments, quartz, and feldspars. One hundred and two samples were collected from all areas of the mine, from the stockpile, black sand areas, tailings and Te Akeake Sands. Samples were collected with the primary focus on the next predicted mining path and secondly on gaining a good geographic spread throughout the mine. All samples were analysed for the dry, wet and particle density, the porosity and the magnetic, non-magnetic and clay minerals content.Stockpile samples had an average magnetic mineral content of 92 percent. Dry, wet and particle density values for stockpile material exceed all values from untreated ironsand samples with average values of 2.8g/cm3, 2.9g/cm3 and 4.4g/cm3 respectively. Black sand samples from the mine came from various areas such as the central area, the forest, the southern area and the benches. All black sand samples are remarkably consistent, with dry and wet density values between 2.3 û 2.5g/cm3 and particle densities that range from 3.7 to 3.9g/cm3. The porosity values are comparable to all other areas of the mine (average 37 per cent). The tailings and Te Akeake Sands have different physical properties due to their different mineral contents. The dry, wet and particle densities are all lower than that of all other areas with averages of 2.1g/cm3, 2.2g/cm3 and 3.3g/cm3 respectively. These lower values reflect the lower magnetic mineral content (average 18 per cent) and the associated increase in non-magnetic mineral content (average 78 per cent).

Jan 1, 2002

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By A S. Venkatesh, A Das

The Precambrian iron ore of Singhbhum-North Orissa region of eastern India occurs as part of the horseshoe-shaped broad synclinorium known as the Iron Ore Group (IOG) of rocks, which hosts the most important iron ore deposits in India. The Jilling-Langalota iron ore deposits are part of the IOG. Detailed mineralogical characterisation of different ore types has been carried out using transmitted and reflected light microscopy. Scanning electron microscope-energy dispersive spectroscopy (SEM- EDS), X-ray diffraction (XRD) and X-ray fluorescence (XRF) have also been used with a view to test the amenability of these ore types for beneficiation requirements. It has been observed that haematite, martite and goethite are the main iron-bearing minerals. Kaolinite and quartz are the major gangue mineral phases. Considerable mineralogical, textural and compositional variations have been observed among the different ore types. Characterisation data reveals that the massive and hard-laminated ores are of higher grade with very few interlocking textures having haematite and martite as major mineral constitutents. The soft-laminated lateritic and friable ores are relatively low-grade varieties containing various proportions of impurities with complex interlocking textures. The soft-laminated and lateritic ores are porous in nature and contain friable oxide and hydroxides of iron along with kaolinite, gibbsite and quartz. The occurrence of kaolinite, gibbsite and hydrated oxides along the cavities and weaker mineral planes of haematite and martite has been observed. The friable nature and high alumina content of these ores are attributed to these secondary phases. The nature of these ores is responsible for producing large amounts of alumina-rich slime during mining and handling operations. Suitable beneficiation schemes have been recommended for each type based on detailed characterisation investigations on these ores.

Jan 1, 2007

By G MacSporran, I Sheppard

The practical application of LaneÆs theory on optimum cut-off grade policy has to date proved difficult for selective stoping in large-scale underground mining. The key to determining an optimum cut-off grade is the ability to rapidly perform complex mine layout designs combined with rapid output of multiple potential schedules. This paper describes aspects of the detailed investigation into estimating a practical static cut-off grade for the two main orebodies in Mount Isa MineÆs Enterprise Mine. Rule based automated scheduling software was used to evaluate thirteen different stoping layouts (including design infrastructure and capital development) of the Enterprise MineÆs two main orebodies, with over 200 schedules generated. The investigation illustrates the application of commercially available software to solve the problems of generating multiple cut-off grade stope designs and achieving the otherwise insurmountable task of rapidly generating and valuing multiple scenarios for each stoping layout. Each scenario was evaluated using modelled net cash flows of the mining, concentrating and smelting operations of the company and calculating NPV. The cut-off grade for each orebody was selected based on the cut-off grade that achieved maximum NPV û with an appropriate production rate. Underground mine scheduling is a complex task involving the adherence to a number of simple scheduling rules and the balancing of several competing drivers. The study also found that: while each scheduling rule itself is simple, the compounding complexities of their interaction preclude manual scheduling from being a realistic option. there is a maximum sustainable rate of production possible for any given stoping layout, and that the actual maximum production rate is also a function of the required number of years of sustainable production. the optimal cut-off grade was different for each orebody û a recognition of the impact of the different characteristics of each orebody.

Jan 1, 2003

The stratigraphic sequence west of Mount Isa contains the Judenan Beds, Eastern Creek Volcanics, and May Downs gneiss. It is an incomplete sequence as major north-south faults divide the area into four separatezones containing portions of these different units. The first three zones, which occur directly to the west of the Mount Isa Fault, consist of quartzites and quartz-mica schists which are uncorrelatable between zones but have been grouped together as the Judenan Beds. The most western zone contains an incomplete section of Eastern Creek Volcanics which rests conformably on a unit believed to be equivalent to the Mount Guide Quartzite; this is again underlain by the May Downs gneiss. A detailed description of the rock types is presented, but only a broad stratigraphic correlation is possible with the very much thicker sequence to the east of Mount Isa.The age of sedimentation is believed to be Lower Proterozoic and it may not occur in the type of geosynclinal basin envisaged by previous authors.This sequence is intruded by many small basic intrusions and also the Sybella Granite with its associated microgranite and pegmatites. The Sybella Granite consists of both a massive and a foliated phase; the latteris generally restricted to the margin of the main granite mass.Four regional metamorphic zones have been identified on the basis of their pelitic mineral assemblages; these are a chlorite, biotite, biotite-cordierite, and a sillimanite zone; separating each are prominent north-south faults.This metamorphism is a regional metamorphism which accompanies the first generation folding of the area and is not associated with the emplacement of the Sybella Granite. A very localized retrogressive metamorphism is also found in some areas of second generation folding.

Jan 1, 1972

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

By A Roudnev, P Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for both the end users and pump manufacturers. The traditional approach has been to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve froth pumping capability of mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance.CITATION:Loderer, P and Roudnev, A, 2018. A reliable solution for pumping mineral froth with challenging froth volume, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By McConachie W. J

Introduction.Ore Bodies.Lead.Copper.Ground.Main Haulage Levels.Stope Preparation.Stoping Practice.General.Longitudinal Stopes-Ring Drilled.Parallel Hole Drilled.Transverse Stopes -Ring Drilled.Parallel Hole Drilled.Charging and Wiring.Fragmentation.Pillar Recovery.Special Applications of Blast Holes.General Drilling Data.Future Trends.Acknowledgements.INTRODUCTIONThe purpose of this paper is to present a detailed account of current blast hole stoping practice at Mount Isa. Details of blast hole machines, types of diamond bits and performances are covered in B. E. Logan's paper "Diamond Drills and Bits".ORE BODIESThis brief description is limited to an outline of the salient features of the Black Star lead and copper bodies.

Jan 1, 1953

By C Riley, N Davies, J Carpenter, I Lipton

Nautilus Minerals Incorporated (Nautilus) recently announced the worldÆs first Seafloor Massive Sulfide Mineral Resource at Solwara 1 in the Bismarck Sea, Papua New Guinea . The discovery, exploration and resource modelling of this æblack smokerÆ system located 1500 m under the sea involved unique technological development. Whilst the resource estimation methodology had similarities with approaches adopted for analogous volcanic-hosted massive sulfide (VHMS) deposits, specific parts of the resource estimate called for new ways of assessing data. This paper discusses several innovative methods for collecting and assessing Solwara 1 exploration data. This ia an ABSTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This report on the 5th International Conference on Underground Space and Earth Sheltered Structures, which was held at the University of Technology, Delft, the Netherlands, on 2 to 5 August 1992, was submitted to the members of the Australian Underground Construction and Tunnelling Association. The report describes the conference themes and outcomes and puts forward some observations about a growing world-wide interest in the promotion of appropriate uses of underground space. The report recommends the creation of an Australian centre for research to bring together a wide range of professional disciplines and to focus attention on the potential benefits of using underground space.

Jan 1, 1993

By M A. Vinokurova, V M. Mullov

Due to treatment of refractory carbonaceous low-grade gold ores a new technology providing improved precious metal recovery is required. For this reason, a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon in leach (CIL)-process for intensive cyanidation tailings and the recleaned concentrate was developed. The proposed technology allows to decrease preg-robbing activities of concentrates treated by subsequent cyanidation. Total gold recovery by the proposed technology from the ore with a head grade of 0.8 g/t was 83.9 per cent. The gold loading onto the activated carbon from CIL process was 6.500 g/t.

Jan 1, 2007

The Pacific Rim countries of Australia, New Zealand, Papua New Guinea, Indonesia, Fiji, Philippines and Solomon Islands will be reviewed from an equity investors perspective. The following areas will be covered: ò Country risks ò Exploration spending and activity ò Project development ò Taxation ò Relative cost of doing business ò Environmental considerations ò Political/bureaucratic situations ò Capital raising ò Equity markets as a source of funds ò Developing market funds The aim of the paper will be to outline the most attractive areas for investment by equity and private funds plus documenting the changes needed in the less favourable countries if they are to attract investors.

Jan 1, 1995

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

The optimization of management structure systems for coal mines is undertaken with the use of economic and mathematical models of the monitoring, manufacturing, and functional subdivisions of the systems. The main para- meter to be minimized is economic loss result ing from organization faults and this is achieved, in part, by optimum distribution of both technological objects and engineering and technical personnel. Models used are of the "gated" type, parameters for which are derived from analysis of manufacturing processes and from automatic information systems. The use of these models ofmanagement structures is only part of the process of optimization of those structures for coal mining operations.

Jan 1, 1977

It is a facet of modern-day life that change, even of a revolu- tionary nature, normally passes without comment. People have become so conditioned to continuous improve- ments in every aspect of their lives that they would be surprised only if there were to be no change. This paper seeks to demonstrate the extent of technical change, and to indicate the need for a fuller advantage to be taken of the technologies available, or potentially available, to the profes- sion. It contends that the mineral industry has been particularly slow to embrace technical change, and has good reason to con- sider an improved attitude for both prosperity and survival.

Jan 1, 1988

By Tooth MA

Mining, metallurgical and engineering consultants have made a considerable contribution to mining industry development in Australia. Expertise has been developed locally to a high level during the last decade which has contributed to the success of many recent mining projects. The services available'cover the whole spectrum from the evaluation of ore reserves, through feasibility study and financial evaluation to design, project management and commissioning. Using these services effectively and economically is an objective which client and consultant both must pursue but which is not always achieved. This paper discusses some aspects of the use of consultants which the experience of the authors has shown to be of prime Importance

Jan 1, 1975

By T Iwadachi, T Fujisawa an, G R. Alvear

A large amount of Be2C and BeO is formed during the Cu-Be alloy production process, because beryllium is a highly reactive element. Carbide and oxide formation impairs the production yield and the quality of the Cu-Be alloy products, and therefore should be minimised. As a first step for solving these problems in the process, the following thermodynamic properties of the Cu-Be-C-O system were investigated. Based on the results, the equilibrium relations of the Cu-Be-C-O system were clarified and the operational conditions of the current Cu-Be alloy production process were also examined and discussed.

Jan 1, 2000