Search Documents

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

By T Gartner

This paper describes the design, manufacture and site services associated with the supply of mine hoists for the new mine under construction by Falconbridge Limited in Ontario, Canada. Two new shafts are being sunk, and the hoisting equipment at each shaft can be summarised as follows: Ventilation shaft:4.66 m diameter double-drum second-hand hoist, originally in operation at San Manuel Mine, Arizona, to be used as the shaft sinking hoist. The second-hand hoist presented a challenge in that during its previous life, the hoist had been intensively operated during service at San Manuel Mine, and this paper describes the scope of refurbishment work undertaken, both electrically and mechanically, to ensure future reliable operation, together with the requirement to meet Canadian and Ontario regulations and codes of practice. 3.05 m diameter new single drum auxiliary hoist to be used as a second means of egress. Main shaft:4.57 m diameter new double-drum hoist to be used initially as the shaft sinking hoist, and subsequently to be converted to the equivalent of a single-drum multi-rope hoist for service duties during the production phase; 5.49 m diameter new double-drum hoist to be used for skip hoisting during the production phase; and 3.05 m diameter new single drum auxiliary hoist.The new hoists are all designed to comply with SABS requirements such that hoisting with reduced rope safety factors will be possible in the future. This paper describes the principles involved both mechanically and electrically. Particular attention is paid to the conversion of the main shaft service hoist from a double-drum sinking hoist to a multi-rope hoist.This paper describes the ac electrical powertrains (drives and motors) used that eliminate the need for harmonic filters and reactive power compensation equipment since they exhibit no negative effects on the utility electrical network system. This paper describes the logistical challenges of installing, commissioning and setting to work a series of five hoists in a short time frame.

Jan 1, 2005

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

In terms of tunnelling the mining industry is generally thought of as the crude cousin of the civil construction industry. Mining has tended to concentrate on speed and flexibility rather than the high standards required in civil tunnelling. Historically this difference has been based on the belief that such high standards were not required by the mining industry, they would slow down the development of the project and as a result increase the costs and extend the time period between start up and a positive cashflow.For civil works the construction of a tunnel is the project, for mining the construction of declines, crosscuts and drives are merely the means of accessing the orebody so that the real work can begin û MINING. Extraction of ore is the core business of most mining companies û it is what pays the bills.Though most mining companies have the equipment, the people, the knowledge and the ability to excavate tunnels, in the past mining companies did not appear to put the same energy into their tunnelling operations as they put into improving their ore extraction operations. In the past decade this appears to have changed, many mining companies now realise how important the correct excavation of a decline is to the success of the overall mining operation. They began to recognise that there were cost benefits to be gained in using the correct development techniques without overly sacrificing the benefits of speed and flexibility.This recognition also coincided with the growth of underground contractors whose predominant work was primary development (declines and ore access crosscuts and drives). The contractors again had the same knowledge, the same people, and similar equipment but their focus was different from that of the mining company û the contractors were focused on the development of the mine, the excavation of declines, crosscuts and drives. These deliverables were the contractorsÆ core business û itÆs what paid the bills.

Jan 1, 1999

By R L. Verburg, R Johnstone

DeBeers Canada Mining Inc (DeBeers) recently submitted an Environmental Assessment (EA) for its proposed Snap Lake Diamond Mine located in Northwest Territories, Canada. As part of the EA process, a site water quality management plan must be developed. Plan development requires an integrated approach such that the key factors influencing water quality can be identified and managed to minimise potential impact. A system model was therefore developed to simulate the site-wide water quality conditions and mass loadings to the principal environmental receptor of concern, Snap Lake, during operations and post-closure. Requirements of the simulation included integrating hydrology, geochemistry, hydrogeology and site management practices in a dynamic way. A unique feature of the site was the need to accommodate a complex flow system that included a feedback loop between lake water and mine water. A system model was constructed using the GoldSim software package that integrated on-site water quality and flow measurements, as well as results from independent groundwater flow and geochemical modelling efforts. The GoldSim model simulated concurrently the movement of 39 solutes through the subsurface mine and surface facilities. Solute sources considered included four different waste rock and tailings types, explosives use in the mine, treatment plant discharge, and recycled process water for dust suppression. Separate solubility constraints were identified for different regions of the flow system (eg underground mine; treatment facility; surface water bodies). Kinetic test data were used to derive temperature-dependent rate constants for use in calculating mass inputs from surface sources such as waste rock piles. The model generated water quality estimates over time for a variety of management scenarios at several potential discharge locations. The integrated approach used by the model was effective in identifying the significance of key factors influencing overall water quality such as explosives use, mine water inflow rates, waste rock reaction rates, site/mine management options, and effectiveness of treatment. The model provides an example of an effective tool for comprehensive, integrated system evaluation and management.

Jan 1, 2003

Slope stability is a critical safety and production issue for open cut mines. The æslope stability radarÆ has been developed to remotely scan a rock slope to continuously measure the movement of the face. The system can detect and alert movements of a rough wall with sub-millimetre precision, and with reliability and resolution. The advantage of the slope stability radar over other monitoring techniques is that it provides full area coverage without the need for mounted reflectors or equipment on the wall. In addition, the radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. The measurement technique is tolerant of vibrations and overcomes the need for a highly stable footing required by traditional surveying systems, making it easy to move from one location to another. The system is self-powered and designed for minimal maintenance. Radar displacement images, co-registered with digital photography images, are transferred from the radar site in the pit to the mine office via a radio telemetry link. Custom-written software provides mine managers and geotechnical engineers with a complete picture of slope movements over defined time intervals. The time-history of the movement of any selected points or regions on the slope can also be displayed. Also provided is the ability to set movement thresholds that will trigger alarms at the radar site or mine office. The system has been used at numerous coal and metalliferous mines in Australia, and has provided real-time monitoring of slope stability during active mining operations. More than 20 rock wall and spoil failures have been captured by the system, and on every occasion adequate warning was provided to mine operators. The high level of movement precision and broad area coverage of the rock face provides a better understanding of the geodynamics, which leads to extra warning time. This technology enables a radical change in the management of risks in open cut mining operations.

Jan 1, 2003

Solid Energy New Zealand (SENZ) uses a 20+ year period for integrated planning of all its business activities. It has an ongoing program of coal resource assessment to optimise future mines within this 20 year period, using a six step resource and mine planning process. Desktop review and conceptual study at preliminary Levels 1 and 2 are based on general coal resource information. Further coal resource investigations are carried out for the more detailed evaluations in secondary assessment, prefeasibility study, feasibility study and detailed engineering from Levels 3 to 6. At Levels 1 and 2, completing conceptual planning, including preliminary resource evaluation and economic appraisal to the target cost uncertainty level of ¦33 per cent, is challenging in New ZealandÆs highly variable geological and geographical conditions. Where coal deposit geometries are relatively simple, approximate methods for determining pit limits using overburden strip ratios, seam thickness, physical boundaries, and quality cut-offs may be sufficient. Many New Zealand coalfields are however complicated structurally, with multiple seams and extensive folding and faulting. Coal seams are characterised by variable dip, thickness, and quality over relatively short distances. In the North IslandÆs Waikato coalfields, coal is typically overlain by weak sediments and clay rich strata that necessitate very flat cut and fill slope angles. The proximity of these deposits to major infrastructure (including towns, highways and rail lines), significant environmental features such as the Waikato river and lakes, and valuable dairy farmland, add further complexity. Traditional preliminary mine planning techniques applied in these conditions are insufficient. Pit optimisation software, widely used in the metalliferous mining industry since the 1980s, offers the ability to analyse many more specific factors affecting pit limits, mine layouts, and economics, with more rigour and for a much larger number of scenarios, than traditional methods allow. SENZ therefore decided to adapt and use æWhittleÆ pit optimisation software for Level 2 analysis of several Waikato opencast prospects. This paper describes this work.

Jan 1, 2005

By O V. Vasyukova

Formation of porphyry-style ore deposits starts with the metal extraction from magmas at so-called magmatic-hydrothermal transition (MHT). The processes and compositions at MHT are difficult to study as the record of them is poorly preserved. As the MHT is characterised by massive crystallisation of quartz, including quartz æeyesÆ and veins, their study can elucidate questions related to metal transport and deposition. Quartz grains from the porphyry deposits all over the world (Antapaccay, Peru; Batu Hijao, Indonesia; Climax, USA; Panguna, PNG; Far Southeast porphyry, Philippines; Rio Blanco, Chile; Omsukchan, Russia) were studied by optical, SEM-CL and BSE microscopy, electron microprobe and LA ICPMS. Quartz grains, even within each sample, have different shapes (rounded, egg-shaped, amoeboid or euhedral) and cathodoluminesence (CL) patterns (shape, number and width of bands in CL images). The outer layers of quartz are markedly different, which is unexpected if the grains had formed in the same conditions. Inflections and blurring of CL bands are often structurally associated with fractures that are commonly healed with secondary quartz and associated fluid inclusions. Our results show that quartz æeyesÆ could not crystallise from a silicate melt as normal phenocrysts. It is likely that in situ segregation of residual SiO2- and H2O-rich liquid and its solidification followed by coagulation (eg formation of silica-gel globules) took place in the magma (crystal mush) during MHT. Such globules could remain in a plastic state for a long time even at rather low temperatures. The solidification of globules occurred after bands of different composition had formed and led to fracturing of solidified and inflection of unconsolidated layers. All fluids (liquid and vapour) released from the original silicagel during solidification were trapped as inclusions (aqueous, salt-rich and sulfide). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

A metallurgical balance drawn around a mineral processing plant or smelter must involve all process streams crossing the plant boundary. Modern sampling theory, as formulated by Gy, and sound statistical method can be used to determine the uncertainties in the observed assays for the set of balance analytes and in the mass flow rates of the process streams for the balance period. These uncertainties can then be used together with the material balance equations to arrive at adjusted component mass flows that satisfy the material balances exactly. To determine whether or not the data is consistent with the level of uncertainty in the data and with the material balance equations, a goodness of fit test is applied. This goodness of fit criterion is the principal tool to quantify the quality of the material balances. The mathematical structure of the statistical material balance problem poses a number of challenges. For example, while the variances of the adjusted component mass flows do not vanish, the variances of the sums of the adjusted component mass flows about each balance node do vanish, simply because the balancing computation demands that the balances close exactly. Even though it can be shown that the variances of the adjusted component mass flows are always lower than the estimates for the corresponding unadjusted component flows, it is still not possible to construct a confidence interval on the component mass flow into (and out of) a balance node using the adjusted component flows. On the face of it, such a confidence interval is exactly what is most desired from the balance calculations. The problem arises because the balance problem is a data adjustment rather than a parameter estimation problem. It is possible, however, to calculate the recovery of a component to a product stream and determine a confidence interval for the recovery value. It is also possible to calculate an uncertainty in the mass flow of any balance species in any process stream, before and after balancing.

Jan 1, 2005

By D Pepper

Despite the limited literature regarding the pressure filtration of mine tailings (compared to the large number of papers published each year on paste thickening of tailings) the number of mines dry stacking filtered tailings is approximately equal to the number of mines storing tailings in paste form. Main drivers for filtering tailings are: water recovery, future rehabilitation costs for tailings storage area and permitting requirements. In arid climates, the cost and scarcity of water justify the capital and operating costs associated with pressure filters. Further justification for filtered tailings is the potential for progressive reclamation of the dry stack, which can proceed earlier and faster than the reclamation of a tailings dam.Filtered tailings must be transported to the storage area by trucks or conveyors. For dry stacking, 70 - 80 per cent solids content (by mass) is typically acceptable, however the primary goal is to provide a filter cake that is consolidated and dry enough to prevent bridging and build-up on the materials handling equipment. It has been observed that high average solids contents (~70 per cent) can be achieved while the centre of the filter cakes is still wet and sticky, presenting challenges for the transportation of the solids. Appropriate controls must be in place to ensure consistently easy to handle solids are discharged from the filter.FLSmidth has installed two fine coal tailings dewatering systems in the United States. One of these systems incorporates a Deep Cone Thickener« upstream of the filter press to minimise the amount of water that must be filtered, while the other tailings filter press is fed by a high rate thickener. The operation and performance of these filters is discussed and compared to the lab testing used to size the full-scale equipment.CITATION:Pepper, D, 2012. Operation of filter presses for tailings dewatering, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 241-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

This paper summarises the performance of the gold exploration industry in the Western World since 1970, with particular emphasis on the period 1985 - 2003. It identifies the number and size of major (ie >1 million ounce) primary gold discoveries made over this period by location and type of company. Estimates are also made of the likely contribution from smaller discoveries down to 0.1 million ounces. It also assesses the overall trend in the percentage of grassroot discoveries that are converted into mines, and the time taken to get them into production. By comparing the discovery data against total exploration expenditures it is possible to determine the average unit cost of finding a major gold deposit. It is significant to note that the average unit cost per discovery and per ounce of resource has tripled over the last 30 years. An attempt is made to determine the overall economic value generated by the industry. This is based on a detailed analysis of the rates of return and the Net Present Values (NPVs) of 109 major gold projects. After including an adjustment for discoveries not modelled, the NPVs are compared against the total amount of money spent on exploration to determine the value-to-cost ratio for the industry. Based on historical spot gold prices and tax rules, it is found that the return on investment for gold exploration in the Western World over the period 1985 - 2003 was around five per cent real after-tax. The returns achieved in the US and Australia was significantly higher than that for Canada. The returns also appear to have declined in recent years. With regard to the relative performance of junior versus major companies, the paper estimates that the junior sector accounted for 30 - 40 per cent of the total exploration expenditure, and were was associated with 34 per cent of the total number of major deposits, 27 per cent of the contained ounces and 25 per cent of the economic value found.

Jan 1, 2004

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By E du Plessis, M Rowley, M Fallon, F Golenya, R Swanson, I Robertson

"Check sampling programs were undertaken at Barrick Australia Pacific LimitedÆs Lawlers and Plutonic mine sites in Western Australia. The programs identified that the sampling, sample preparation and assaying protocols required modification to ensure acceptable precision (reproducibility) for each gold mineralisation type. These case studies describe the processes used to identify the: inconsistent precision different types of test work programs that were conducted to quantify the appropriateness for each mineralisation type steps used to modify the protocols.The type of test work conducted included: a duplicate series heterogeneity test for particulate gold mineralisation in the Lawlers gold deposit screen fire assay test work on duplicate subsamples for arsenopyrite associated mineralisation at the Plutonic gold deposit.Each test work program required a detailed scope specifying the sample selection criteria, sample preparation and assaying steps. The aim of the test work flow chart design was to ensure the assay precision between the different particle sizes or duplicate sample pairs could be measured and calculated. In the screen fire test work the true grade of the primary sample was calculated and compared against each subsample.A high quality assay laboratory was utilised for the test work. All samples were fire assayed and the gold grade determined using a gravimetric finish. The assay results were validated and the data was analysed using tables and graphs in spreadsheets. Following data analysis a modified sample preparation and assaying protocol for each mineralisation type was designed for use by the principal assay laboratories. Following implementation of the new protocols, routine check samples were collected during the sample preparation and assaying stages to monitor the performance of the new protocol.CITATION:Fallon, M, Rowley, M, Du Plessis, E, Golenya, F, Robertson, I and Swanson, R, 2012. Confirming the sampling, sample preparation and assaying protocols used at two Yilgarn gold deposits, in Proceedings Sampling 2012, pp 47-62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By P A. Dowd

This paper describes an integrated approach to the evaluation of ore loss and ore dilution via geostatistical simulation of in situ geology and grade characteristics, simulation of blasting mechanisms and simulation of loading from a blast muck pile. The approach is demonstrated on a case study. The sequential Gaussian method is used to simulate in situ bench grades on the scale of the smallest selectable volume within a blast muck pile. The simulated grades of these component volumes are interpreted as the reality that would be available with exhaustive sampling. The simulated bench is subjected to a blast simulator, based on the SCRAMBLE model, which effectively moves each of the component model volumes to its final resting place in the blast muck pile. Ore/waste delineation and selective loading processes are applied to the simulated muck pile to determine the degree of selectivity that can be achieved by various sizes of loader and types of loading and to quantify ore dilution and ore loss. An in situ model representing the reality of knowing only the data and information that are available from specific grade control drilling and sampling grids is obtained by sampling the geostatistically simulated model on a specified grid. The volumes comprising the in situ model are then populated by estimates based only on the data and from the specified grade control drilling and sampling grids. Different drilling and sampling grids are used to generate different models, each reflecting the levels of data and information available. Selectivity is assessed as a function of the drilling and sampling grids as well as the size and type of loader. Performance is assessed against the ideal selectivity that could be achieved on the perfect knowledge model comprising the simulated values of each component volume. Costs, prices and financial criteria enable an optimal selection of the grade control drilling grid, size of loader, type of loading and blast design.

Jan 1, 2004

By Miller D. R

The mineral exploration and extraction industries have gained major cost and efficiency benefits from the use of computers. However these industries are now at a cross-roads with two seemingly disparate developments - that of an increasing number of complex geoscience databases and, at the same time, the merging of all known data for the particular regions at minimal cost. These two developments can be managed by the development and of an industry accepted geoscience data model and dictionary. This will provide a common basis of understanding for geoscience data through a common language and a common structure for geoscience information. Integration of specialist systems and databases can then proceed efficiently. The development of a data model is going ahead with consensus from the mining industry. This is a joint government and industry funded project and managed through the Australian Mineral Industries Research Association, AMIRA. AMIRA is a well known research broker to the Australian mining industry obtaining sponsorship for projects both from private and government groups. The AMIRA project, P431, called the Geoscience Data Model, is to be the Australian standard data model for geoscience disciplines. The requirement for a standard geoscience data model has been recognised in Australia for some time. In October 1991, the Australian Government Geoscience Database Policy Advisory Committee (GGDPAC) established a Geoscience Data Standards Working Group which drafted a comprehensive list of data categories of the geoscience area. An AMIRA project called AMDEX was established to develop a transfer standard for the mining industry data at about the same time as this committee was in operation. The first AMDEX sponsors meeting was held in May 1991. It was proposed to use the US Spatial Data Transfer Standard (SDTS) as the basis to transfer mining data in AMDEX. A limited data model of mining data to be transferred was developed for the AMDEX standard under SDTS. The Australian Geological Survey Organisation (AGSO) saw the need to extend this and develop a complete data model for the geosciences and proposed this as a new project to AMIRA. This was strongly supported by GGDPAC which lead to sponsorship of the project from most state geological surveys. The Geoscience Data Model can be broken down into separate data models for a number of geoscience themes and sponsorship obtained so far will enable models to be developed for a comprehensive set of themes selected by the project sponsors. Further sponsorship is required to enable a more complete coverage of the geoscience area to be developed. Sponsorship for the Geoscience Data Model has been strong from the geological surveys and there was some effort by GGDPAC to promote the project in these organisations. An Australian geoscience data model is of immediate use to the geological surveys in assisting the standardising of huge quantities of geoscience data held by government agencies and it is preferable that this be an Australia-wide standard.

Jan 1, 1995

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006