Search Documents

By Kissell F. N, Thimons E. D

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined- out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room- and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1988

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Y Li, L Zhang, G Li, S C. Dominy

Qiagong skarn iron (copper) deposit is located in Xietongmen County of Tibet, China (N 29¦52Æ14.9ö, E 88¦24Æ10.3ö). It is situated at the middle-western Gangdese porphyry copper-belt. Mineralisation is related to a Himalayan porphyry intrusion, with the mineralised body occurring at the contact zone between the Tertiary Takena Formation carbonate rocks and Himalayan monzonitic granite porphyry. The melt, melt-fluid and fluid inclusions were observed in early quartz, with most abundant fluid inclusions in quartz, calcite and garnet from the skarn. The geology and inclusion assemblage show a close relationship between iron (copper) mineralisation and a Himalayan porphyry intrusion. Based on preliminary inclusion studies, this paper discussed the characteristics, evolution of ore-forming fluid and affiliation to the Himalayan porphyry intrusion. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Hayward P. G

Complex ores, characterised by intimate intergrowths between minerals, have previously been treated by flotation with limited success. The most common problem has been that the liberation size is often finer than the lower size limit for selection flotation. A technique has been developed in which the problem is overcome by the use of a selective agglomeration procedure in which the values are coalesced with oil to a size suitable for flotation prior to introduction into the flotation machine. A complex lead ore was characterised by QEM*SEM mineralogy as having a mean galena liberation size of 15 ¦m. The best recovery of lead at 50 per cent Pb grade by standard flotation was 53 per cent. After application of the procedure, 86 per cent recovery was obtained after a single cleaner step. The oil functions as a bridging liquid in the presence of conventional collectors which render the mineral oleophillic.

Jan 1, 1991

By S Gannon, J Abols, T Hughes

In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilises conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX«100å ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a three-stage crushing circuit to crush the gold ore to minus 1 mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJs and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plantsÆ design, commissioning and operation are discussed.

Jan 1, 2006

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

By Ibaragi K

High grade ores were intersected in 1981 by a scout drill carried out by the Metal Mining Agency of Japan during a reconnaissance dril ling programme. The original aim of the hole was to explore a deep target where geophysical anczralies overlapped the abandoned old drifts (gravity- high, resistivity-low by airborne EM, and resistivity-low near the surface and high at depth by Schlumberger deep sounding). Subsequently, a follow-up drilling programm was commenced by the Sumitcrro Metal Mining Co Ltd, and all the 18 holes intersected high grade ores. The resources were then "guestimated" to contain ca.120 tonnes gold with an average grade of 80g/t Au between -40m and +120n a.s.l. The underground development was started in December 1982 and the first crosscut intersected the ore body at 100m level (a.s.l.) in July 1985.

Jan 1, 1987

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

Production of oic at BHP Minerals Pty Ltd's Cannington Mine commenced in May 1997. The initial sloping blocks at the [nine are located in the upper part of the Footwall Lead lode, and the Hangingwall Lead and Glenholme Breccia lodes. This paper discusses the geological investigations, interpretation and modelling that was undertaken for the Footwall Lead lode production block at Cannington Mine, as well as providing a basic geological introduction to the Cannington deposit.

Jan 1, 1997

Evaluation of tyre chains has been taking place at King Island Scheelite for several years. Results indicate that tyre life has been greatly improved in all cases. Good cost sav- ings are resulting on small loaders. The worth of chains is difficult to prove on larger loaders under the conditions at King Island Scheelite. However, the dramatic decrease in the number of punctures has convinced the Company that chains are worthwhile on some larger loaders.

Jan 1, 1977

The title of my address today is "Oil and Gas Valuations - A Simplistic View of Some Critical Issues". Alternatively I could have called this address "Pitfalls for investors' and corporates in accessing Independent Experts Reports" 'as in this brief 12 minute talk I will briefly comment on some common misconceptions with regard to the valuation of exploration areas and production interests, and comment on how the draft release guidelines address these issues.

Jan 1, 1989

By Kister H

Hoesch HUttenwerke AG, Dortmund, West Germany, is an integrated steel work of the Estel-group. The nominal annual production capacity-is about 7 Mio tons of steel. Hoesch has along experience in operation of diffe-rent types of slag granulation plants and of utilization of the granulated product. This experience is used to granulate a large amount of blast furnace slag and to process it in own cement plants and produce blast fur-nace cement.

Jan 1, 1979

The process of defining the external environmental costs of mining activities, devising appropriate mechanisms to internalise them is complex and is likely to be a gradual.Australia's competitiveness could be seriously affected if , in terms of incorporating environmental costs, we were to exceed other resource producing nations.Australia has a great deal at stake in the debate and therefore we need to proceed carefully and be fully aware of the environmental and economic issues.

Jan 1, 1992

An integrated approach to risk management to complement insurance is the sustainable way forward for the modem organisation. For risk management to work, its various aspects need to operate interactively, not in isolation from insurance. This is the approach recommended in this paper. The risk management process is a strategic method for reducing an organisation's total cost of risk. Well established and basic risk management techniques will help identify and achieve risk management Objectives.

Jan 1, 1994

By Blom W. M

Shareholders, creditors, government agencies and auditors all have a different perspective of financial reports which is determined by the uses to which they put the information disclosed in the report.Shareholders today are better informed than previously and are more aware of the market in which they are investing. This is the result of the increasing role of institutional investors and the increasing reliance being placed on analysts to interpret financial information.

Jan 1, 1990

By Braes J. R, Neale J. R

The New Broken Hill Consolidated Limited (NBHC) mine currently produces 1.42 million tonnes of silver, lead and zinc ore annually. All of this ore is treated by the NBHC milling ccx[plex. This paper describes the crushing, grinding, flotation and filtration circuits used in the treatment of this ore and lists the major items of equignent used in these circuits. Metallurgical results, manning levels and consumption rates of reagents and grinding media are shown.

Jan 1, 1983